On Fri, May 23, 2014 at 1:03 AM, Grant Likely <grant.likely@xxxxxxxxxx> wrote:
> On Tue, 20 May 2014 13:42:02 +0300, Grygorii Strashko <grygorii.strashko@xxxxxx> wrote:
>> The commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef
>> "of/irq: do irq resolution in platform_get_irq" from Rob Herring -
>> moves resolving of the interrupt resources in platform_get_irq().
>> But this solution isn't complete because platform_get_irq_byname()
>> need to be modified the same way.
>>
>> Hence, fix it by adding interrupt resolution code at the
>> platform_get_irq_byname() function too.
>>
>> Cc: Russell King <linux@xxxxxxxxxxxxxxxx>
>> Cc: Rob Herring <robh@xxxxxxxxxx>
>> Cc: Tony Lindgren <tony@xxxxxxxxxxx>
>> Cc: Grant Likely <grant.likely@xxxxxxxxxx>
>> Cc: Thierry Reding <thierry.reding@xxxxxxxxx>
>>
>> Signed-off-by: Grygorii Strashko <grygorii.strashko@xxxxxx>
>
> Applied, Thanks.
As of next-20150526, the ST u8500 Snowball board has been failing boot
in linux-next, and was bisected down to this patch (commit
ad69674e73a1 in -next). Full boot failure attached.
I have not dug any deeper, but can confirm that next-20140526 with
this patch reverted boots again on the snowball board.
Kevin
Connected to snowball console [channel connected] (~$quit to exit)
(user:khilman) is already connected
~$hardreset
Command(snowball console)> hardreset
(user:khilman) Reboot snowball
MCDE: startup failed
sec_bridge: ISSWAPI_FLUSH_BOOT_CODE: 2
EMMC: 0, MMC: 1
In: serial
Out: serial
Err: serial
Net: smc911x-0
Hit any key to stop autoboot: 1 0
U8500 $
U8500 $ version
U8500 $ versionsetenv ethaddr 6e:e6:84:36:8e:9e
U-Boot 2009.11 (sept. 19 2011 - 17:03:11)
U8500 $ setenv ethaddr 6e:e6:84:36:8e:9esetenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4
Can't overwrite "ethaddr"
U8500 $ setenv bootargs console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254'
U8500 $ setenv netargs 'setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:::none:192.168.1.254'if test -n ${initenv}; then run initenv; fi
U8500 $ if test -n ${initenv}; then run initenv; fiif test -n ${preboot}; then run preboot; fi
U8500 $ if test -n ${preboot}; then run preboot; fisetenv autoload no; setenv autoboot no
U8500 $ setenv autoload no; setenv autoboot nodhcp
U8500 $ dhcp
smc911x: detected LAN9221 controller
smc911x: phy initialized
smc911x: MAC 6e:e6:84:36:8e:9e
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.1.159
U8500 $ setenv serverip 192.168.1.2
setenv serverip 192.168.1.2
U8500 $ if test -n ${netargs}; then run netargs; fi
if test -n ${netargs}; then run netargs; fi
U8500 $ tftp 0x00800000 192.168.1.2:tmp/snowball-CDNi__/tmpIadw30-uImage
tftp 0x00800000 192.168.1.2:tmp/snowball-CDNi__/tmpIadw30-uImage
smc911x: detected LAN9221 controller
smc911x: phy initialized
smc911x: MAC 6e:e6:84:36:8e:9e
Using smc911x-0 device
TFTP from server 192.168.1.2; our IP address is 192.168.1.159
Filename 'tmp/snowball-CDNi__/tmpIadw30-uImage'.
Load address: 0x800000
Loading: *#################################################################
#################################################################
#################################################################
##############################
done
Bytes transferred = 3295829 (324a55 hex)
U8500 $ printenv bootargs
printenv bootargs
bootargs=console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0:::none:192.168.1.254
U8500 $ bootm 0x00800000
bootm 0x00800000
## Booting kernel from Legacy Image at 00800000 ...
Image Name: Linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3295765 Bytes = 3.1 MB
Load Address: 00008000
Entry Point: 00008000
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x300
[ 0.000000] Linux version 3.15.0-rc7-next-20140526 (buildslave@kbuilderdedi01) (gcc version 4.7.1 (Ubuntu/Linaro 4.7.1-5ubuntu1~ppa1) ) #1 SMP PREEMPT Mon May 26 11:59:19 CEST 2014
[ 0.000000] CPU: ARMv7 Processor [412fc091] revision 1 (ARMv7), cr=10c5787d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Calao Systems Snowball platform with device tree
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DB8500 v2.2 [0x008500b2]
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0611500, node_mem_map eeff5000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 528 pages used for memmap
[ 0.000000] HighMem zone: 67584 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 7 pages/cpu @eefb8000 s7552 r8192 d12928 u32768
[ 0.000000] pcpu-alloc: s7552 r8192 d12928 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260624
[ 0.000000] Kernel command line: console=ttyAMA2,115200n8 debug earlyprintk rw root=/dev/mmcblk0p3 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0:::none:192.168.1.254
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1032848K/1048576K available (4397K kernel code, 208K rwdata, 1384K rodata, 187K init, 234K bss, 15728K reserved, 270336K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc05ad90c (5783 kB)
[ 0.000000] .init : 0xc05ae000 - 0xc05dcd80 ( 188 kB)
[ 0.000000] .data : 0xc05de000 - 0xc0612120 ( 209 kB)
[ 0.000000] .bss : 0xc061212c - 0xc064cac4 ( 235 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000030] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 65536000000000ns
[ 0.000183] Switching to timer-based delay loop
[ 0.001251] Console: colour dummy device 80x30
[ 0.001281] Calibrating delay loop (skipped), value calculated using timer frequency.. 4.80 BogoMIPS (lpj=24000)
[ 0.001312] pid_max: default: 32768 minimum: 301
[ 0.001495] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001525] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002288] CPU: Testing write buffer coherency: ok
[ 0.002838] missing device node for CPU 0
[ 0.002990] missing device node for CPU 1
[ 0.003021] CPU0: thread -1, cpu 0, socket 3, mpidr 80000300
[ 0.003143] Setting up static identity map for 0x42bcb8 - 0x42bd10
[ 0.003265] L2C-310 erratum 753970 enabled
[ 0.003295] L2C-310 cache controller enabled, 8 ways, 512 kB
[ 0.003295] L2C-310: CACHE_ID 0x410000c5, AUX_CTRL 0x7ec60800
[ 0.060943] CPU1: Booted secondary processor
[ 0.060943] CPU1: thread -1, cpu 1, socket 3, mpidr 80000301
[ 0.061004] Brought up 2 CPUs
[ 0.061004] SMP: Total of 2 processors activated.
[ 0.061035] CPU: All CPU(s) started in SVC mode.
[ 0.061462] devtmpfs: initialized
[ 0.064636] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 2
[ 0.065093] pinctrl core: initialized pinctrl subsystem
[ 0.065795] regulator-dummy: no parameters
[ 0.074615] NET: Registered protocol family 16
[ 0.075347] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.076354] cpuidle: using governor ladder
[ 0.076385] cpuidle: using governor menu
[ 0.078613] gpio 8012e000.gpio: at address f812e000
[ 0.079071] gpio 8012e080.gpio: at address f812e080
[ 0.079498] gpio 8000e000.gpio: at address f800e000
[ 0.079925] gpio 8000e080.gpio: at address f800e080
[ 0.080383] gpio 8000e100.gpio: at address f800e100
[ 0.080810] gpio 8000e180.gpio: at address f800e180
[ 0.081268] gpio 8011e000.gpio: at address f811e000
[ 0.081695] gpio 8011e080.gpio: at address f811e080
[ 0.082122] gpio a03fe000.gpio: at address fa3fe000
[ 0.082916] pinctrl-nomadik soc:pinctrl: initialized Nomadik pin control driver
[ 0.083618] PRCMU firmware: U8500(2), version 3.4.3
[ 0.084808] ab8500-core ab8500-core.0: detected chip, AB8500 rev. 3.0
[ 0.084838] ab8500-core ab8500-core.0: switch off cause(s) (0x20):
[ 0.084838] "Battery level lower than power on reset threshold"
[ 0.084869] ab8500-core ab8500-core.0: turn on reason(s) (0x20):
[ 0.084899] "Vbus Detect (USB)"
[ 0.087799] abx500-gpio pinctrl-ab8500.0: added gpiochip
[ 0.092285] abx500-gpio pinctrl-ab8500.0: registered pin controller
[ 0.092315] abx500-gpio pinctrl-ab8500.0: initialized abx500 pinctrl driver
[ 0.093658] DB8500 PRCMU initialized
[ 0.100982] db8500-vape: no parameters
[ 0.101196] db8500-varm: no parameters
[ 0.101379] db8500-vmodem: no parameters
[ 0.101593] db8500-vpll: no parameters
[ 0.101776] db8500-vsmps1: no parameters
[ 0.101959] db8500-vsmps2: at 1800 mV
[ 0.102172] db8500-vsmps3: no parameters
[ 0.102355] db8500-vrf1: no parameters
[ 0.102508] db8500-sva-mmdsp: no parameters
[ 0.102691] db8500-sva-mmdsp-ret: no parameters
[ 0.102905] db8500-sva-pipe: no parameters
[ 0.103088] db8500-sia-mmdsp: no parameters
[ 0.103302] db8500-sia-mmdsp-ret: no parameters
[ 0.103485] db8500-sia-pipe: no parameters
[ 0.103668] db8500-sga: no parameters
[ 0.103851] db8500-b2r2-mcde: no parameters
[ 0.104034] db8500-esram12: no parameters
[ 0.104217] db8500-esram12-ret: no parameters
[ 0.104400] db8500-esram34: no parameters
[ 0.104583] db8500-esram34-ret: no parameters
[ 0.104797] Serial: AMBA PL011 UART driver
[ 0.105224] 80120000.uart: ttyAMA0 at MMIO 0x80120000 (irq = 43, base_baud = 0) is a PL011 rev3
[ 0.105865] 80121000.uart: ttyAMA1 at MMIO 0x80121000 (irq = 51, base_baud = 0) is a PL011 rev3
[ 0.106445] 80007000.uart: ttyAMA2 at MMIO 0x80007000 (irq = 58, base_baud = 0) is a PL011 rev3
[ 0.709106] console [ttyAMA2] enabled
[ 0.713317] abx500-clk abx500-clk.0: register clocks for ab850x
[ 0.751556] dma40 801c0000.dma-controller: hardware rev: 3 @ 0x801c0000 with 8 physical and 256 logical channels
[ 0.761993] dma40 801c0000.dma-controller: 7 of 8 physical DMA channels available
[ 0.769470] dma40 801c0000.dma-controller: [d40_phy_res_init] INFO: channel 4 is misconfigured (0)
[ 0.778442] dma40 801c0000.dma-controller: [d40_phy_res_init] INFO: channel 5 is misconfigured (0)
[ 0.787414] dma40 801c0000.dma-controller: [d40_phy_res_init] INFO: channel 6 is misconfigured (0)
[ 0.829864] dma40 801c0000.dma-controller: initialized
[ 0.836029] en-3v3-fixed-supply: 3300 mV
[ 0.840576] ab8500-ext-supply1: 1800 mV
[ 0.844848] ab8500-ext-supply2: 1360 mV
[ 0.849060] ab8500-ext-supply3: 3400 mV
[ 0.860321] V-DISPLAY: 2500 <--> 2900 mV at 2500 mV
[ 0.865447] V-DISPLAY: supplied by ab8500-ext-supply3
[ 0.870910] V-eMMC1: 1100 <--> 3300 mV at 2900 mV
[ 0.875793] V-eMMC1: supplied by ab8500-ext-supply3
[ 0.880981] V-MMC-SD: 1200 <--> 2910 mV at 2910 mV
[ 0.885955] V-MMC-SD: supplied by ab8500-ext-supply3
[ 0.891235] V-INTCORE: at 1250 mV
[ 0.894866] V-TVOUT: 2000 mV
[ 0.898040] V-AUD: 2000 mV
[ 0.901031] V-AMIC1: 2050 mV
[ 0.904174] V-AMIC2: 2050 mV
[ 0.907318] V-DMIC: 1800 mV
[ 0.910400] V-CSI/DSI: 1200 mV
[ 0.913574] V-CSI/DSI: Failed to create debugfs directory
[ 0.919677] ab8500-debug ab8500-debug.0: First irq not found, err -22
[ 0.926147] ab8500-debug: probe of ab8500-debug.0 failed with error -22
[ 0.933227] ssp-pl022 80002000.ssp: ARM PL022 driver, device ID: 0x01080022
[ 0.940246] ssp-pl022 80002000.ssp: mapped registers from 0x80002000 to f0084000
[ 0.948120] ssp-pl022 80003000.ssp: ARM PL022 driver, device ID: 0x01080022
[ 0.955139] ssp-pl022 80003000.ssp: mapped registers from 0x80003000 to f0086000
[ 0.962890] ssp-pl022 8011a000.spi: ARM PL022 driver, device ID: 0x00080023
[ 0.969879] ssp-pl022 8011a000.spi: mapped registers from 0x8011a000 to f0088000
[ 0.977600] ssp-pl022 80112000.spi: ARM PL022 driver, device ID: 0x00080023
[ 0.984619] ssp-pl022 80112000.spi: mapped registers from 0x80112000 to f008a000
[ 0.992340] ssp-pl022 80111000.spi: ARM PL022 driver, device ID: 0x00080023
[ 0.999328] ssp-pl022 80111000.spi: mapped registers from 0x80111000 to f008c000
[ 1.007049] ssp-pl022 80129000.spi: ARM PL022 driver, device ID: 0x00080023
[ 1.014068] ssp-pl022 80129000.spi: mapped registers from 0x80129000 to f008e000
[ 1.022430] usbcore: registered new interface driver usbfs
[ 1.028015] usbcore: registered new interface driver hub
[ 1.033477] usbcore: registered new device driver usb
[ 1.038909] abx5x0-usb ab8500-usb.0: Link status irq not found
[ 1.044860] platform ab8500-usb.0: Driver abx5x0-usb requests probe deferral
[ 1.052642] nmk-i2c 80004000.i2c: initialize Nomadik I2C at [mem 0x80004000-0x80004fff] on virtual base f0090000
[ 1.063323] nmk-i2c 80122000.i2c: initialize Nomadik I2C at [mem 0x80122000-0x80122fff] on virtual base f0092000
[ 1.073913] nmk-i2c 80128000.i2c: initialize Nomadik I2C at [mem 0x80128000-0x80128fff] on virtual base f0094000
[ 1.084655] nmk-i2c 80110000.i2c: initialize Nomadik I2C at [mem 0x80110000-0x80110fff] on virtual base f0096000
[ 1.095123] nmk-i2c 8012a000.i2c: initialize Nomadik I2C at [mem 0x8012a000-0x8012afff] on virtual base f0098000
[ 1.106140] Advanced Linux Sound Architecture Driver Initialized.
[ 1.113037] cfg80211: Calling CRDA to update world regulatory domain
[ 1.119659] (NULL device *): failed to get platform sw_conv_end irq
[ 1.125976] (NULL device *): failed to get platform hw_conv_end irq
[ 1.140777] Switched to clocksource dbx500-prcmu-timer
[ 1.158691] NET: Registered protocol family 2
[ 1.163665] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 1.170745] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.177337] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.183776] TCP: reno registered
[ 1.187011] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.192993] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.199523] NET: Registered protocol family 1
[ 1.204162] RPC: Registered named UNIX socket transport module.
[ 1.210052] RPC: Registered udp transport module.
[ 1.214813] RPC: Registered tcp transport module.
[ 1.219512] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.227630] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 1.242248] msgmni has been set to 1489
[ 1.246734] bounce: pool size: 64 pages
[ 1.250579] io scheduler noop registered
[ 1.254516] io scheduler deadline registered
[ 1.258972] io scheduler cfq registered (default)
[ 1.264068] uart-pl011 80120000.uart: DMA channel TX dma0chan12
[ 1.270019] uart-pl011 80120000.uart: DMA channel RX dma0chan13
[ 1.275970] uart-pl011 80121000.uart: DMA channel TX dma0chan14
[ 1.281921] uart-pl011 80121000.uart: DMA channel RX dma0chan15
[ 1.287872] uart-pl011 80007000.uart: DMA channel TX dma0chan16
[ 1.293853] uart-pl011 80007000.uart: DMA channel RX dma0chan17
[ 1.305633] brd: module loaded
[ 1.338226] libphy: smsc911x-mdio: probed
[ 1.421020] smsc911x 50000000.ethernet eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=50000000.etherne:01, irq=-1)
[ 1.432647] smsc911x 50000000.ethernet eth0: MAC Address: d6:35:1e:0a:80:29
[ 1.441497] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
[ 1.453369] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
[ 1.460571] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.472076] musb-hdrc musb-hdrc.0.auto: Error applying setting, reverse things back
[ 1.479827] HS USB OTG: no transceiver configured
[ 1.484558] musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
[ 1.492309] platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
[ 1.500183] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
[ 1.512023] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
[ 1.519226] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.530731] musb-ux500 musb-hdrc.0.auto: Error applying setting, reverse things back
[ 1.539184] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.1.auto
[ 1.551025] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.1.auto) status -22
[ 1.558258] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.569732] musb-hdrc musb-hdrc.1.auto: Error applying setting, reverse things back
[ 1.577453] HS USB OTG: no transceiver configured
[ 1.582183] musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517
[ 1.589935] platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral
[ 1.597778] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.1.auto
[ 1.609619] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.1.auto) status -22
[ 1.616851] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.628326] musb-ux500 musb-hdrc.1.auto: Error applying setting, reverse things back
[ 1.636779] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.2.auto
[ 1.648620] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.2.auto) status -22
[ 1.655853] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.667327] musb-hdrc musb-hdrc.2.auto: Error applying setting, reverse things back
[ 1.675048] HS USB OTG: no transceiver configured
[ 1.679748] musb-hdrc musb-hdrc.2.auto: musb_init_controller failed with status -517
[ 1.687530] platform musb-hdrc.2.auto: Driver musb-hdrc requests probe deferral
[ 1.695373] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.2.auto
[ 1.707214] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.2.auto) status -22
[ 1.714447] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.725921] musb-ux500 musb-hdrc.2.auto: Error applying setting, reverse things back
[ 1.734344] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.3.auto
[ 1.746185] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.3.auto) status -22
[ 1.753417] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.764892] musb-hdrc musb-hdrc.3.auto: Error applying setting, reverse things back
[ 1.772613] HS USB OTG: no transceiver configured
[ 1.777313] musb-hdrc musb-hdrc.3.auto: musb_init_controller failed with status -517
[ 1.785095] platform musb-hdrc.3.auto: Driver musb-hdrc requests probe deferral
[ 1.792938] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.3.auto
[ 1.804779] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.3.auto) status -22
[ 1.812011] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.823486] musb-ux500 musb-hdrc.3.auto: Error applying setting, reverse things back
[ 1.831909] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.4.auto
[ 1.843749] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.4.auto) status -22
[ 1.850982] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.862457] musb-hdrc musb-hdrc.4.auto: Error applying setting, reverse things back
[ 1.870178] HS USB OTG: no transceiver configured
[ 1.874877] musb-hdrc musb-hdrc.4.auto: musb_init_controller failed with status -517
[ 1.882659] platform musb-hdrc.4.auto: Driver musb-hdrc requests probe deferral
[ 1.890472] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.4.auto
[ 1.902313] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.4.auto) status -22
[ 1.909545] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.921020] musb-ux500 musb-hdrc.4.auto: Error applying setting, reverse things back
[ 1.929443] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.5.auto
[ 1.941284] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.5.auto) status -22
[ 1.948516] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 1.959991] musb-hdrc musb-hdrc.5.auto: Error applying setting, reverse things back
[ 1.967712] HS USB OTG: no transceiver configured
[ 1.972442] musb-hdrc musb-hdrc.5.auto: musb_init_controller failed with status -517
[ 1.980194] platform musb-hdrc.5.auto: Driver musb-hdrc requests probe deferral
[ 1.988006] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.5.auto
[ 1.999847] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.5.auto) status -22
[ 2.007080] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.018585] musb-ux500 musb-hdrc.5.auto: Error applying setting, reverse things back
[ 2.026977] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.6.auto
[ 2.038848] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.6.auto) status -22
[ 2.046081] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.057556] musb-hdrc musb-hdrc.6.auto: Error applying setting, reverse things back
[ 2.065307] HS USB OTG: no transceiver configured
[ 2.070037] musb-hdrc musb-hdrc.6.auto: musb_init_controller failed with status -517
[ 2.077789] platform musb-hdrc.6.auto: Driver musb-hdrc requests probe deferral
[ 2.085662] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.6.auto
[ 2.097473] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.6.auto) status -22
[ 2.104705] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.116210] musb-ux500 musb-hdrc.6.auto: Error applying setting, reverse things back
[ 2.124633] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.7.auto
[ 2.136474] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.7.auto) status -22
[ 2.143707] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.155181] musb-hdrc musb-hdrc.7.auto: Error applying setting, reverse things back
[ 2.162902] HS USB OTG: no transceiver configured
[ 2.167602] musb-hdrc musb-hdrc.7.auto: musb_init_controller failed with status -517
[ 2.175384] platform musb-hdrc.7.auto: Driver musb-hdrc requests probe deferral
[ 2.183227] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.7.auto
[ 2.195068] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.7.auto) status -22
[ 2.202301] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.213775] musb-ux500 musb-hdrc.7.auto: Error applying setting, reverse things back
[ 2.222198] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.8.auto
[ 2.234039] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.8.auto) status -22
[ 2.241271] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.252746] musb-hdrc musb-hdrc.8.auto: Error applying setting, reverse things back
[ 2.260467] HS USB OTG: no transceiver configured
[ 2.265197] musb-hdrc musb-hdrc.8.auto: musb_init_controller failed with status -517
[ 2.272949] platform musb-hdrc.8.auto: Driver musb-hdrc requests probe deferral
[ 2.280792] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.8.auto
[ 2.292633] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.8.auto) status -22
[ 2.299865] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.311340] musb-ux500 musb-hdrc.8.auto: Error applying setting, reverse things back
[ 2.319732] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.9.auto
[ 2.331604] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.9.auto) status -22
[ 2.338806] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.350311] musb-hdrc musb-hdrc.9.auto: Error applying setting, reverse things back
[ 2.358032] HS USB OTG: no transceiver configured
[ 2.362731] musb-hdrc musb-hdrc.9.auto: musb_init_controller failed with status -517
[ 2.370483] platform musb-hdrc.9.auto: Driver musb-hdrc requests probe deferral
[ 2.378326] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.9.auto
[ 2.390167] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.9.auto) status -22
[ 2.397399] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.408874] musb-ux500 musb-hdrc.9.auto: Error applying setting, reverse things back
[ 2.417297] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.10.auto
[ 2.429260] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.10.auto) status -22
[ 2.436584] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.448059] musb-hdrc musb-hdrc.10.auto: Error applying setting, reverse things back
[ 2.455871] HS USB OTG: no transceiver configured
[ 2.460571] musb-hdrc musb-hdrc.10.auto: musb_init_controller failed with status -517
[ 2.468444] platform musb-hdrc.10.auto: Driver musb-hdrc requests probe deferral
[ 2.476348] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.10.auto
[ 2.488281] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.10.auto) status -22
[ 2.495605] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.507080] musb-ux500 musb-hdrc.10.auto: Error applying setting, reverse things back
[ 2.515624] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.11.auto
[ 2.527557] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.11.auto) status -22
[ 2.534881] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.546356] musb-hdrc musb-hdrc.11.auto: Error applying setting, reverse things back
[ 2.554168] HS USB OTG: no transceiver configured
[ 2.558868] musb-hdrc musb-hdrc.11.auto: musb_init_controller failed with status -517
[ 2.566711] platform musb-hdrc.11.auto: Driver musb-hdrc requests probe deferral
[ 2.574645] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.11.auto
[ 2.586578] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.11.auto) status -22
[ 2.593902] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.605377] musb-ux500 musb-hdrc.11.auto: Error applying setting, reverse things back
[ 2.613891] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.12.auto
[ 2.625823] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.12.auto) status -22
[ 2.633148] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.644622] musb-hdrc musb-hdrc.12.auto: Error applying setting, reverse things back
[ 2.652435] HS USB OTG: no transceiver configured
[ 2.657135] musb-hdrc musb-hdrc.12.auto: musb_init_controller failed with status -517
[ 2.665008] platform musb-hdrc.12.auto: Driver musb-hdrc requests probe deferral
[ 2.672912] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.12.auto
[ 2.684844] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.12.auto) status -22
[ 2.692169] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.703643] musb-ux500 musb-hdrc.12.auto: Error applying setting, reverse things back
[ 2.712158] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.13.auto
[ 2.724090] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.13.auto) status -22
[ 2.731414] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.742889] musb-hdrc musb-hdrc.13.auto: Error applying setting, reverse things back
[ 2.750701] HS USB OTG: no transceiver configured
[ 2.755432] musb-hdrc musb-hdrc.13.auto: musb_init_controller failed with status -517
[ 2.763275] platform musb-hdrc.13.auto: Driver musb-hdrc requests probe deferral
[ 2.771209] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.13.auto
[ 2.783142] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.13.auto) status -22
[ 2.790435] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.801910] musb-ux500 musb-hdrc.13.auto: Error applying setting, reverse things back
[ 2.810424] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.14.auto
[ 2.822357] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.14.auto) status -22
[ 2.829650] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.841125] musb-hdrc musb-hdrc.14.auto: Error applying setting, reverse things back
[ 2.848937] HS USB OTG: no transceiver configured
[ 2.853668] musb-hdrc musb-hdrc.14.auto: musb_init_controller failed with status -517
[ 2.861511] platform musb-hdrc.14.auto: Driver musb-hdrc requests probe deferral
[ 2.869415] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.14.auto
[ 2.881347] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.14.auto) status -22
[ 2.888641] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.900146] musb-ux500 musb-hdrc.14.auto: Error applying setting, reverse things back
[ 2.908660] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.15.auto
[ 2.920593] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.15.auto) status -22
[ 2.927886] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.939392] musb-hdrc musb-hdrc.15.auto: Error applying setting, reverse things back
[ 2.947204] HS USB OTG: no transceiver configured
[ 2.951904] musb-hdrc musb-hdrc.15.auto: musb_init_controller failed with status -517
[ 2.959747] platform musb-hdrc.15.auto: Driver musb-hdrc requests probe deferral
[ 2.967681] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.15.auto
[ 2.979614] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.15.auto) status -22
[ 2.986938] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 2.998413] musb-ux500 musb-hdrc.15.auto: Error applying setting, reverse things back
[ 3.006927] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.16.auto
[ 3.018859] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.16.auto) status -22
[ 3.026184] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.037658] musb-hdrc musb-hdrc.16.auto: Error applying setting, reverse things back
[ 3.045471] HS USB OTG: no transceiver configured
[ 3.050170] musb-hdrc musb-hdrc.16.auto: musb_init_controller failed with status -517
[ 3.058044] platform musb-hdrc.16.auto: Driver musb-hdrc requests probe deferral
[ 3.065979] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.16.auto
[ 3.077911] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.16.auto) status -22
[ 3.085235] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.096710] musb-ux500 musb-hdrc.16.auto: Error applying setting, reverse things back
[ 3.105224] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.17.auto
[ 3.117156] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.17.auto) status -22
[ 3.124481] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.135955] musb-hdrc musb-hdrc.17.auto: Error applying setting, reverse things back
[ 3.143798] HS USB OTG: no transceiver configured
[ 3.148498] musb-hdrc musb-hdrc.17.auto: musb_init_controller failed with status -517
[ 3.156341] platform musb-hdrc.17.auto: Driver musb-hdrc requests probe deferral
[ 3.164276] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.17.auto
[ 3.176177] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.17.auto) status -22
[ 3.183502] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.194976] musb-ux500 musb-hdrc.17.auto: Error applying setting, reverse things back
[ 3.203491] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.18.auto
[ 3.215423] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.18.auto) status -22
[ 3.222747] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.234222] musb-hdrc musb-hdrc.18.auto: Error applying setting, reverse things back
[ 3.242065] HS USB OTG: no transceiver configured
[ 3.246765] musb-hdrc musb-hdrc.18.auto: musb_init_controller failed with status -517
[ 3.254608] platform musb-hdrc.18.auto: Driver musb-hdrc requests probe deferral
[ 3.262512] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.18.auto
[ 3.274444] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.18.auto) status -22
[ 3.281768] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.293243] musb-ux500 musb-hdrc.18.auto: Error applying setting, reverse things back
[ 3.301757] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.19.auto
[ 3.313690] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.19.auto) status -22
[ 3.321014] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.332489] musb-hdrc musb-hdrc.19.auto: Error applying setting, reverse things back
[ 3.340301] HS USB OTG: no transceiver configured
[ 3.345031] musb-hdrc musb-hdrc.19.auto: musb_init_controller failed with status -517
[ 3.352874] platform musb-hdrc.19.auto: Driver musb-hdrc requests probe deferral
[ 3.360809] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.19.auto
[ 3.372741] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.19.auto) status -22
[ 3.380035] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.391510] musb-ux500 musb-hdrc.19.auto: Error applying setting, reverse things back
[ 3.400024] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.20.auto
[ 3.411956] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.20.auto) status -22
[ 3.419281] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.430786] musb-hdrc musb-hdrc.20.auto: Error applying setting, reverse things back
[ 3.438598] HS USB OTG: no transceiver configured
[ 3.443298] musb-hdrc musb-hdrc.20.auto: musb_init_controller failed with status -517
[ 3.451171] platform musb-hdrc.20.auto: Driver musb-hdrc requests probe deferral
[ 3.459075] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.20.auto
[ 3.471008] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.20.auto) status -22
[ 3.478302] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.489807] musb-ux500 musb-hdrc.20.auto: Error applying setting, reverse things back
[ 3.498321] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto
[ 3.510253] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22
[ 3.517578] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.529052] musb-hdrc musb-hdrc.21.auto: Error applying setting, reverse things back
[ 3.536865] HS USB OTG: no transceiver configured
[ 3.541595] musb-hdrc musb-hdrc.21.auto: musb_init_controller failed with status -517
[ 3.549438] platform musb-hdrc.21.auto: Driver musb-hdrc requests probe deferral
[ 3.557342] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.21.auto
[ 3.569274] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.21.auto) status -22
[ 3.576599] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.588073] musb-ux500 musb-hdrc.21.auto: Error applying setting, reverse things back
[ 3.596618] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto
[ 3.608551] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22
[ 3.615875] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.627349] musb-hdrc musb-hdrc.22.auto: Error applying setting, reverse things back
[ 3.635162] HS USB OTG: no transceiver configured
[ 3.639862] musb-hdrc musb-hdrc.22.auto: musb_init_controller failed with status -517
[ 3.647735] platform musb-hdrc.22.auto: Driver musb-hdrc requests probe deferral
[ 3.655639] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.22.auto
[ 3.667572] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.22.auto) status -22
[ 3.674896] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.686370] musb-ux500 musb-hdrc.22.auto: Error applying setting, reverse things back
[ 3.694885] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto
[ 3.706817] pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.23.auto) status -22
[ 3.714141] pinctrl-nomadik soc:pinctrl: could not request pin 256 (GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
[ 3.725616] musb-hdrc musb-hdrc.23.auto: Error applying setting, reverse things back
[ 3.733428] HS USB OTG: no transceiver configured
[ 3.738128] musb-hdrc musb-hdrc.23.auto: musb_init_controller failed with status -517
[ 3.746002] platform musb-hdrc.23.auto: Driver musb-hdrc requests probe deferral
[ 3.753906] pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already requested by a03e0000.usb_per5; cannot claim for musb-hdrc.23.auto
~$off
# PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'>
# PYBOOT: Time: 116.49 seconds.
# PYBOOT: Result: FAIL
