Update VI and CSI bindings to add port and endpoint nodes as per
media video-interfaces DT binding document.
Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
---
.../display/tegra/nvidia,tegra20-host1x.txt | 92 +++++++++++++++++++++-
1 file changed, 90 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
index 4731921..ac63ae4a 100644
--- a/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
+++ b/Documentation/devicetree/bindings/display/tegra/nvidia,tegra20-host1x.txt
@@ -51,8 +51,16 @@ of the following host1x client modules:
- vi
- Tegra210:
- power-domains: Must include venc powergate node as vi is in VE partition.
- - Tegra210 has CSI part of VI sharing same host interface and register space.
- So, VI device node should have CSI child node.
+
+ ports (optional node)
+ vi can have optional ports node and max 6 ports are supported. Each port
+ should have single 'endpoint' child node. All port nodes are grouped under
+ ports node. Please refer to the bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ csi (required node)
+ Tegra210 has CSI part of VI sharing same host interface and register space.
+ So, VI device node should have CSI child node.
- csi: mipi csi interface to vi
@@ -65,6 +73,46 @@ of the following host1x client modules:
- power-domains: Must include sor powergate node as csicil is in
SOR partition.
+ channel (optional nodes)
+ Maximum 6 channels are supported with each csi brick as either x4 or x2
+ based on hw connectivity to sensor.
+
+ Required properties:
+ - reg: csi port number. Valid port numbers are 0 through 5.
+ - nvidia,mipi-calibrate: Should contain a phandle and a specifier
+ specifying which pads are used by this CSI port and need to be
+ calibrated. See also ../display/tegra/nvidia,tegra114-mipi.txt.
+
+ Each channel node must contain 2 port nodes which can be grouped
+ under 'ports' node and each port should have a single child 'endpoint'
+ node.
+
+ ports node
+ Please refer to the bindings defined in
+ Documentation/devicetree/bindings/media/video-interfaces.txt
+
+ ports node must contain below 2 port nodes.
+ port@0 with single child 'endpoint' node always a sink.
+ port@1 with single child 'endpoint' node always a source.
+
+ port@0 (required node)
+ Required properties:
+ - reg: 0
+
+ endpoint (required node)
+ Required properties:
+ - data-lanes: an array of data lane from 1 to 4. Valid array
+ lengths are 1/2/4.
+ - remote-endpoint: phandle to sensor 'endpoint' node.
+
+ port@1 (required node)
+ Required properties:
+ - reg: 1
+
+ endpoint (required node)
+ Required properties:
+ - remote-endpoint: phandle to vi port 'endpoint' node.
+
- epp: encoder pre-processor
Required properties:
@@ -340,6 +388,18 @@ Example:
ranges = <0x0 0x0 0x54080000 0x2000>;
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ imx219_vi_in0: endpoint {
+ remote-endpoint = <&imx219_csi_out0>;
+ };
+ };
+ };
+
csi@838 {
compatible = "nvidia,tegra210-csi";
reg = <0x838 0x1300>;
@@ -362,6 +422,34 @@ Example:
<&tegra_car TEGRA210_CLK_CSI_TPG>;
clock-names = "csi", "cilab", "cilcd", "cile", "csi_tpg";
power-domains = <&pd_sor>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ channel@0 {
+ reg = <0>;
+ nvidia,mipi-calibrate = <&mipi 0x001>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ imx219_csi_in0: endpoint {
+ data-lanes = <1 2>;
+ remote-endpoint = <&imx219_out0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ imx219_csi_out0: endpoint {
+ remote-endpoint = <&imx219_vi_in0>;
+ };
+ };
+ };
+ };
};
};
--
2.7.4
