Hi Erwan
On 5/28/20 9:40 AM, Erwan Le Ray wrote:
Adds usart2_pins_c, usart3_pins_b, usart3_pins_c and uart7_pins_c pins
configurations in stm32mp15-pinctrl.
- usart2_pins_c pins are connected to Bluetooth chip on dk2 board.
- usart3_pins_b pins are connected to GPIO expansion connector on evx board.
- usart3_pins_c pins are connected to GPIO expansion connector on dkx board.
- uart7_pins_c pins are connected to Arduino Uno connector on dkx board.
Signed-off-by: Erwan Le Ray <erwan.leray@xxxxxx>
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index fb98a66977fe..99e399e4e4c3 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -1658,6 +1658,36 @@
};
...
+ usart3_pins_b: usart3-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
On EVx board this line is shared with ETH_CLK. The choice between both
is done thanks to SB23 and default choice is "ETH_CLK". So hardware
update has to be done to use usart3_rts. some words around that in
comment would be great.
Thanks
alex
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+ <STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart3_idle_pins_b: usart3-idle-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('I', 10, ANALOG)>; /* USART3_CTS_NSS */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+ bias-disable;
+ };
+ };
+
+ usart3_sleep_pins_b: usart3-sleep-0 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('I', 10, ANALOG)>, /* USART3_CTS_NSS */
+ <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+ };
+ };
+
+ usart3_pins_c: usart3-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
+ <STM32_PINMUX('B', 13, AF7)>; /* USART3_CTS_NSS */
+ bias-disable;
+ };
+ };
+
+ usart3_idle_pins_c: usart3-idle-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('B', 13, ANALOG)>; /* USART3_CTS_NSS */
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+ bias-disable;
+ };
+ };
+
+ usart3_sleep_pins_c: usart3-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+ <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+ <STM32_PINMUX('B', 13, ANALOG)>, /* USART3_CTS_NSS */
+ <STM32_PINMUX('B', 12, ANALOG)>; /* USART3_RX */
+ };
+ };
+
usbotg_hs_pins_a: usbotg-hs-0 {
pins {
pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
