[PATCH 1/4] arm64: tegra: Enable signal voltage switching on Tegra194 SDMMC1 and SDMMC3

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add pad voltage configuration nodes for SDMMC pads with configurable voltages
and enable supported SD card, SDIO and eMMC modes.

Signed-off-by: Tamás Szűcs <tszucs@xxxxxxxxxxxxx>
---
 arch/arm64/boot/dts/nvidia/tegra194.dtsi | 45 ++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
index 4bc187a4eacd..0a07930e68d1 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/tegra186-hsp.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
+#include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
 #include <dt-bindings/power/tegra194-powergate.h>
 #include <dt-bindings/reset/tegra194-reset.h>
 #include <dt-bindings/thermal/tegra194-bpmp-thermal.h>
@@ -457,6 +458,9 @@
 			clock-names = "sdhci";
 			resets = <&bpmp TEGRA194_RESET_SDMMC1>;
 			reset-names = "sdhci";
+			pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+			pinctrl-0 = <&sdmmc1_3v3>;
+			pinctrl-1 = <&sdmmc1_1v8>;
 			nvidia,pad-autocal-pull-up-offset-3v3-timeout =
 									<0x07>;
 			nvidia,pad-autocal-pull-down-offset-3v3-timeout =
@@ -468,6 +472,15 @@
 			nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
 			nvidia,default-tap = <0x9>;
 			nvidia,default-trim = <0x5>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
+			sd-uhs-sdr104;
+			cap-sdio-irq;
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
 			status = "disabled";
 		};
 
@@ -479,6 +492,9 @@
 			clock-names = "sdhci";
 			resets = <&bpmp TEGRA194_RESET_SDMMC3>;
 			reset-names = "sdhci";
+			pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+			pinctrl-0 = <&sdmmc3_3v3>;
+			pinctrl-1 = <&sdmmc3_1v8>;
 			nvidia,pad-autocal-pull-up-offset-1v8 = <0x00>;
 			nvidia,pad-autocal-pull-down-offset-1v8 = <0x7a>;
 			nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x07>;
@@ -491,6 +507,15 @@
 			nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
 			nvidia,default-tap = <0x9>;
 			nvidia,default-trim = <0x5>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
+			sd-uhs-sdr104;
+			cap-sdio-irq;
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
 			status = "disabled";
 		};
 
@@ -1014,6 +1039,26 @@
 
 			#interrupt-cells = <2>;
 			interrupt-controller;
+
+			sdmmc1_3v3: sdmmc1-3v3 {
+				pins = "sdmmc1-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+			};
+
+			sdmmc1_1v8: sdmmc1-1v8 {
+				pins = "sdmmc1-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+			};
+
+			sdmmc3_3v3: sdmmc3-3v3 {
+				pins = "sdmmc3-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+			};
+
+			sdmmc3_1v8: sdmmc3-1v8 {
+				pins = "sdmmc3-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+			};
 		};
 
 		host1x@13e00000 {
-- 
2.20.1




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux