Re: [PATCH v7 4/5] remoteproc: ingenic: Added remoteproc driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Paul,

On 6/11/20 5:21 PM, Paul Cercueil wrote:
Hi Suman,

Le jeu. 11 juin 2020 à 16:47, Suman Anna <s-anna@xxxxxx> a écrit :
Hi Paul,

On 5/15/20 5:43 AM, Paul Cercueil wrote:
This driver is used to boot, communicate with and load firmwares to the
MIPS co-processor found in the VPU hardware of the JZ47xx SoCs from
Ingenic.

I have a few comments w.r.t pm_runtime usage in this driver.


Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
Acked-by: Mathieu Poirier <mathieu.poirier@xxxxxxxxxx>
---

Notes:
     v2: Remove exception for always-mapped memories
     v3: - Use clk_bulk API
         - Move device-managed code to its own patch [3/4]
         - Move devicetree table right above ingenic_rproc_driver
         - Removed #ifdef CONFIG_OF around devicetree table
         - Removed .owner = THIS_MODULE in ingenic_rproc_driver
         - Removed useless platform_set_drvdata()
     v4: - Add fix reported by Julia
         - Change Kconfig symbol to INGENIC_VPU_RPROC
         - Add documentation to struct vpu
         - disable_irq_nosync() -> disable_irq()
     v5: No change
     v6: Instead of prepare/unprepare callbacks, use PM runtime callbacks
     v7: - Remove use of of_match_ptr()
         - Move Kconfig symbol so that it's in alphabetical order
         - Add missing doc for private structure field aux_base
         - Don't check for (len <= 0) in da_to_va()
         - Add missing \n in dev_info/dev_err messages

  drivers/remoteproc/Kconfig         |   9 +
  drivers/remoteproc/Makefile        |   1 +
  drivers/remoteproc/ingenic_rproc.c | 280 +++++++++++++++++++++++++++++
  3 files changed, 290 insertions(+)
  create mode 100644 drivers/remoteproc/ingenic_rproc.c

diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index fbaed079b299..c4d1731295eb 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -23,6 +23,15 @@ config IMX_REMOTEPROC
          It's safe to say N here.
  +config INGENIC_VPU_RPROC
+    tristate "Ingenic JZ47xx VPU remoteproc support"
+    depends on MIPS || COMPILE_TEST
+    help
+      Say y or m here to support the VPU in the JZ47xx SoCs from Ingenic.
+
+      This can be either built-in or a loadable module.
+      If unsure say N.
+
  config MTK_SCP
      tristate "Mediatek SCP support"
      depends on ARCH_MEDIATEK
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index 0effd3825035..e8b886e511f0 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -10,6 +10,7 @@ remoteproc-y                += remoteproc_sysfs.o
  remoteproc-y                += remoteproc_virtio.o
  remoteproc-y                += remoteproc_elf_loader.o
  obj-$(CONFIG_IMX_REMOTEPROC)        += imx_rproc.o
+obj-$(CONFIG_INGENIC_VPU_RPROC)        += ingenic_rproc.o
  obj-$(CONFIG_MTK_SCP)            += mtk_scp.o mtk_scp_ipi.o
  obj-$(CONFIG_OMAP_REMOTEPROC)        += omap_remoteproc.o
  obj-$(CONFIG_WKUP_M3_RPROC)        += wkup_m3_rproc.o
diff --git a/drivers/remoteproc/ingenic_rproc.c b/drivers/remoteproc/ingenic_rproc.c
new file mode 100644
index 000000000000..189020d77b25
--- /dev/null
+++ b/drivers/remoteproc/ingenic_rproc.c
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Ingenic JZ47xx remoteproc driver
+ * Copyright 2019, Paul Cercueil <paul@xxxxxxxxxxxxxxx>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/remoteproc.h>
+
+#include "remoteproc_internal.h"
+
+#define REG_AUX_CTRL        0x0
+#define REG_AUX_MSG_ACK        0x10
+#define REG_AUX_MSG        0x14
+#define REG_CORE_MSG_ACK    0x18
+#define REG_CORE_MSG        0x1C
+
+#define AUX_CTRL_SLEEP        BIT(31)
+#define AUX_CTRL_MSG_IRQ_EN    BIT(3)
+#define AUX_CTRL_NMI_RESETS    BIT(2)
+#define AUX_CTRL_NMI        BIT(1)
+#define AUX_CTRL_SW_RESET    BIT(0)
+
+struct vpu_mem_map {
+    const char *name;
+    unsigned int da;
+};
+
+struct vpu_mem_info {
+    const struct vpu_mem_map *map;
+    unsigned long len;
+    void __iomem *base;
+};
+
+static const struct vpu_mem_map vpu_mem_map[] = {
+    { "tcsm0", 0x132b0000 },
+    { "tcsm1", 0xf4000000 },
+    { "sram",  0x132f0000 },
+};
+
+/**
+ * struct vpu - Ingenic VPU remoteproc private structure
+ * @irq: interrupt number
+ * @clks: pointers to the VPU and AUX clocks
+ * @aux_base: raw pointer to the AUX interface registers
+ * @mem_info: array of struct vpu_mem_info, which contain the mapping info of
+ *            each of the external memories
+ * @dev: private pointer to the device
+ */
+struct vpu {
+    int irq;
+    struct clk_bulk_data clks[2];
+    void __iomem *aux_base;
+    struct vpu_mem_info mem_info[ARRAY_SIZE(vpu_mem_map)];
+    struct device *dev;
+};
+
+static int ingenic_rproc_start(struct rproc *rproc)
+{
+    struct vpu *vpu = rproc->priv;
+    u32 ctrl;
+
+    enable_irq(vpu->irq);
+
+    /* Reset the AUX and enable message IRQ */
+    ctrl = AUX_CTRL_NMI_RESETS | AUX_CTRL_NMI | AUX_CTRL_MSG_IRQ_EN;
+    writel(ctrl, vpu->aux_base + REG_AUX_CTRL);
+
+    return 0;
+}
+
+static int ingenic_rproc_stop(struct rproc *rproc)
+{
+    struct vpu *vpu = rproc->priv;
+
+    disable_irq(vpu->irq);
+
+    /* Keep AUX in reset mode */
+    writel(AUX_CTRL_SW_RESET, vpu->aux_base + REG_AUX_CTRL);
+
+    return 0;
+}
+
+static void ingenic_rproc_kick(struct rproc *rproc, int vqid)
+{
+    struct vpu *vpu = rproc->priv;
+
+    writel(vqid, vpu->aux_base + REG_CORE_MSG);
+}
+
+static void *ingenic_rproc_da_to_va(struct rproc *rproc, u64 da, size_t len)
+{
+    struct vpu *vpu = rproc->priv;
+    void __iomem *va = NULL;
+    unsigned int i;
+
+    for (i = 0; i < ARRAY_SIZE(vpu_mem_map); i++) {
+        const struct vpu_mem_info *info = &vpu->mem_info[i];
+        const struct vpu_mem_map *map = info->map;
+
+        if (da >= map->da && (da + len) < (map->da + info->len)) {
+            va = info->base + (da - map->da);
+            break;
+        }
+    }
+
+    return (__force void *)va;
+}
+
+static struct rproc_ops ingenic_rproc_ops = {
+    .start = ingenic_rproc_start,
+    .stop = ingenic_rproc_stop,
+    .kick = ingenic_rproc_kick,
+    .da_to_va = ingenic_rproc_da_to_va,
+};
+
+static irqreturn_t vpu_interrupt(int irq, void *data)
+{
+    struct rproc *rproc = data;
+    struct vpu *vpu = rproc->priv;
+    u32 vring;
+
+    vring = readl(vpu->aux_base + REG_AUX_MSG);
+
+    /* Ack the interrupt */
+    writel(0, vpu->aux_base + REG_AUX_MSG_ACK);
+
+    return rproc_vq_interrupt(rproc, vring);
+}
+
+static void ingenic_rproc_disable_clks(void *data)
+{
+    struct vpu *vpu = data;
+
+    pm_runtime_resume(vpu->dev);
+    pm_runtime_disable(vpu->dev);
+
+    clk_bulk_disable_unprepare(ARRAY_SIZE(vpu->clks), vpu->clks);
+}
+
+static int ingenic_rproc_probe(struct platform_device *pdev)
+{
+    struct device *dev = &pdev->dev;
+    struct resource *mem;
+    struct rproc *rproc;
+    struct vpu *vpu;
+    unsigned int i;
+    int ret;
+
+    rproc = devm_rproc_alloc(dev, "ingenic-vpu",
+                 &ingenic_rproc_ops, NULL, sizeof(*vpu));
+    if (!rproc)
+        return -ENOMEM;
+
+    vpu = rproc->priv;
+    vpu->dev = &pdev->dev;
+    platform_set_drvdata(pdev, vpu);
+
+    mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "aux");
+    vpu->aux_base = devm_ioremap_resource(dev, mem);
+    if (IS_ERR(vpu->aux_base)) {
+        dev_err(dev, "Failed to ioremap\n");
+        return PTR_ERR(vpu->aux_base);
+    }
+
+    for (i = 0; i < ARRAY_SIZE(vpu_mem_map); i++) {
+        mem = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+                           vpu_mem_map[i].name);
+
+        vpu->mem_info[i].base = devm_ioremap_resource(dev, mem);
+        if (IS_ERR(vpu->mem_info[i].base)) {
+            ret = PTR_ERR(vpu->mem_info[i].base);
+            dev_err(dev, "Failed to ioremap\n");
+            return ret;
+        }
+
+        vpu->mem_info[i].len = resource_size(mem);
+        vpu->mem_info[i].map = &vpu_mem_map[i];
+    }
+
+    vpu->clks[0].id = "vpu";
+    vpu->clks[1].id = "aux";
+
+    ret = devm_clk_bulk_get(dev, ARRAY_SIZE(vpu->clks), vpu->clks);
+    if (ret) {
+        dev_err(dev, "Failed to get clocks\n");
+        return ret;
+    }
+
+    vpu->irq = platform_get_irq(pdev, 0);
+    if (vpu->irq < 0)
+        return vpu->irq;
+
+    ret = devm_request_irq(dev, vpu->irq, vpu_interrupt, 0, "VPU", rproc);
+    if (ret < 0) {
+        dev_err(dev, "Failed to request IRQ\n");
+        return ret;
+    }
+
+    disable_irq(vpu->irq);
+
+    /* The clocks must be enabled for the firmware to be loaded in TCSM */
+    ret = clk_bulk_prepare_enable(ARRAY_SIZE(vpu->clks), vpu->clks);
+    if (ret) {
+        dev_err(dev, "Unable to start clocks\n");
+        return ret;
+    }

You are enabling the clocks directly here and also trying to manage them through pm_runtime callbacks again.

Yes. The clocks need to be enabled in the probe.

For the preferred non CONFIG_PM case now and lack of prepare/unprepare().


+
+    pm_runtime_irq_safe(dev);

Nothing wrong with this, but this does take an additional reference count on the parent device (a bus device for you??), and also implies that your clk driver code can all run in atomic context so unless you have a strong reason, it is safe to drop this.

The clock driver code can run in atomic context, it is guaranteed by the clk API.

OK.



+    pm_runtime_set_active(dev);

The get_sync below would have been sufficient if you had either limited the clk API above to just clk_prepare, or you could have moved the whole clk API above into your runtime resume callback.

You assume that pm_runtime_get() will enable the clocks, but that's only true if CONFIG_PM is set.

The reason the clocks are enabled in the probe, and pm_runtime_set_active() is called, is that it works whether or not CONFIG_PM is set.

As I said, if the intention is to reflect the clocks active state in rpm status, then pm_runtime_get_noresume() does the job for you instead of get_sync(). pm_runtime_get_sync() typically does 3 things - increment the usage count, invoke your callbacks (enable clocks for you), and sets the status to active, with the last two steps optional depending on usage count.


+    pm_runtime_enable(dev);
+    pm_runtime_get_sync(dev);

If the intention was to increment the usage count with the above sequence, pm_runtime_get_noresume() is better. But dropping all of the above and just using get_sync would have been sufficient.

+    pm_runtime_use_autosuspend(dev);

I don't see any setting of the autosuspend delay (default value is 0). So, you might have as well just not used this at all, and just used pm_runtime_put() below.

Autosuspend delay value can be set from userspace.

Yes, but I don't see a specific purpose for it in your driver. Either you have remoteproc running (and so clocks enabled always), or you don't have a firmware loaded and want clocks disabled (not sure you would want to waste power for certain of amount of time).


+
+    ret = devm_add_action_or_reset(dev, ingenic_rproc_disable_clks, vpu);
+    if (ret) {
+        dev_err(dev, "Unable to register action\n");
+        goto out_pm_put;
+    }
+
+    ret = devm_rproc_add(dev, rproc);
+    if (ret) {
+        dev_err(dev, "Failed to register remote processor\n");
+        goto out_pm_put;
+    }

You are using auto-boot, so the firmware loading is an asynchronous event and most probably you would run through below sequence first, and end up disabling the clocks with an incorrect rpm status.

The driver can auto-load the firmware, but that does not mean it will. We actually don't do that, and load a task-specific firmware onto the remote processor on demand.

Yeah OK, depends on what is preferred by default. If it is more standard practise that the remoteproc is booted by userspace always, then I suggest setting auto_boot as false. But nothing wrong with expecting to boot by default with a starting firmware.


+
+out_pm_put:
+    pm_runtime_put_autosuspend(dev);

And finally, with the remoteproc core rpm patch, this would all have been unnecessary.

+
+    return ret;
+}
+
+static const struct of_device_id ingenic_rproc_of_matches[] = {
+    { .compatible = "ingenic,jz4770-vpu-rproc", },
+    {}
+};
+MODULE_DEVICE_TABLE(of, ingenic_rproc_of_matches);
+
+static int __maybe_unused ingenic_rproc_suspend(struct device *dev)
+{
+    struct vpu *vpu = dev_get_drvdata(dev);
+
+    clk_bulk_disable(ARRAY_SIZE(vpu->clks), vpu->clks);
+
+    return 0;
+}
+
+static int __maybe_unused ingenic_rproc_resume(struct device *dev)
+{
+    struct vpu *vpu = dev_get_drvdata(dev);
+
+    return clk_bulk_enable(ARRAY_SIZE(vpu->clks), vpu->clks);
+}
+
+static const struct dev_pm_ops __maybe_unused ingenic_rproc_pm = {
+    SET_RUNTIME_PM_OPS(ingenic_rproc_suspend, ingenic_rproc_resume, NULL)
+};
+
+static struct platform_driver ingenic_rproc_driver = {
+    .probe = ingenic_rproc_probe,
+    .driver = {
+        .name = "ingenic-vpu",
+#ifdef CONFIG_PM

Not sure why you would want to maintain this conditional, because runtime_pm is a core dependency now for your driver to work properly.

No, it is not - the driver works perfectly fine with CONFIG_PM being disabled, and having a hardcoded dependency on CONFIG_PM is not something we want.

OK, so if IIUC, in general CONFIG_PM is not a typical usage for your MIPS platforms. Your driver is the first non-ARM remoteproc driver :), CONFIG_PM is almost a given on most ARM platforms.

So, I fail to see how your clocks can stay disabled then when CONFIG_PM=n if the remoteproc fails to load with the current code, which was your primary argument for using prepare/unprepare (based on comments on prior versions). It looks to me that your needs are indeed better suited with the prepare/unprepare ops as in your initial series.

And in the case of CONFIG_PM=y, you have three levels of code that enables the clocks (the bare clk API, the pm_runtime_get in probe, and the pm_runtime_get in the remoteproc core). Depending on the rpm status, it may or may not invoke the callbacks.

regards
Suman


Cheers,
-Paul

regards
Suman

+        .pm = &ingenic_rproc_pm,
+#endif
+        .of_match_table = ingenic_rproc_of_matches,
+    },
+};
+module_platform_driver(ingenic_rproc_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Paul Cercueil <paul@xxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("Ingenic JZ47xx Remote Processor control driver");








[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux