Re: R: [PATCH v6 1/2] phy: qualcomm: add qcom ipq806x dwc usb phy driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Jun 05, 2020 at 07:00:04PM +0200, ansuelsmth@xxxxxxxxx wrote:
> > On Wed, Jun 03, 2020 at 03:22:34PM +0200, Ansuel Smith wrote:
> > > This has lost in the original push for the dwc3 qcom driver.
> > > This is needed for ipq806x SoC as without this the usb ports
> > > doesn't work at all.
> > 
> > FWIW I tested this on my RB3011 so feel free to add:
> > 
> > Tested-by: Jonathan McDowell <noodles@xxxxxxxx>
> > 
> > One minor comment; would PHY_QCOM_USB_IPQ806X not be a better
> > choice than PHY_QCOM_IPQ806X_USB given the existing naming?
> > 
>
> Thanks for the feedback. About naming I'm following the sata ipq806x
> naming.  I really hope someone gets this and reviews it since usb is
> broken for a long time now.

Doesn't seem to have made the 5.8 merge window; I note Vinod has done a
bunch of the recent commits to phy/qualcomm/ so adding him to the CC in
addition to Kishon.

> > > Signed-off-by: Andy Gross <agross@xxxxxxxxxxxxxx>
> > > Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> > > ---
> > > v6:
> > > * Use GENMASK instead of hex value
> > > v4:
> > > * Add qcom to specific bindings
> > > v3:
> > > * Use reg instead of regmap phandle
> > > v2:
> > > * Renamed config from PHY_QCOM_DWC3 to PHY_QCOM_IPQ806X_USB
> > > * Rename inline function to generic name to reduce length
> > > * Fix check reported by checkpatch --strict
> > > * Rename compatible to qcom,ipq806x-usb-phy-(hs/ss)
> > >
> > >  drivers/phy/qualcomm/Kconfig                |  12 +
> > >  drivers/phy/qualcomm/Makefile               |   1 +
> > >  drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c | 593
> > ++++++++++++++++++++
> > >  3 files changed, 606 insertions(+)
> > >  create mode 100644 drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c
> > >
> > > diff --git a/drivers/phy/qualcomm/Kconfig
> > b/drivers/phy/qualcomm/Kconfig
> > > index e46824da29f6..9d41c3d12800 100644
> > > --- a/drivers/phy/qualcomm/Kconfig
> > > +++ b/drivers/phy/qualcomm/Kconfig
> > > @@ -91,3 +91,15 @@ config PHY_QCOM_USB_HSIC
> > >  	select GENERIC_PHY
> > >  	help
> > >  	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
> > > +
> > > +config PHY_QCOM_IPQ806X_USB
> > > +	tristate "Qualcomm IPQ806x DWC3 USB PHY driver"
> > > +	depends on ARCH_QCOM
> > > +	depends on HAS_IOMEM
> > > +	depends on OF
> > > +	select GENERIC_PHY
> > > +	help
> > > +	  This option enables support for the Synopsis PHYs present inside
> > the
> > > +	  Qualcomm USB3.0 DWC3 controller on ipq806x SoC. This driver
> > supports
> > > +	  both HS and SS PHY controllers.
> > > +
> > > diff --git a/drivers/phy/qualcomm/Makefile
> > b/drivers/phy/qualcomm/Makefile
> > > index 283251d6a5d9..8629299c1495 100644
> > > --- a/drivers/phy/qualcomm/Makefile
> > > +++ b/drivers/phy/qualcomm/Makefile
> > > @@ -10,3 +10,4 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM)
> > 	+= phy-qcom-ufs-qmp-14nm.o
> > >  obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-
> > qmp-20nm.o
> > >  obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
> > >  obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
> > > +obj-$(CONFIG_PHY_QCOM_IPQ806X_USB)		+= phy-qcom-
> > ipq806x-usb.o
> > > diff --git a/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c
> > b/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c
> > > new file mode 100644
> > > index 000000000000..f37cd8760118
> > > --- /dev/null
> > > +++ b/drivers/phy/qualcomm/phy-qcom-ipq806x-usb.c
> > > @@ -0,0 +1,593 @@
> > > +// SPDX-License-Identifier: GPL-2.0-only
> > > +/* Copyright (c) 2014-2015, Code Aurora Forum. All rights reserved.
> > > + *
> > > + * This program is free software; you can redistribute it and/or modify
> > > + * it under the terms of the GNU General Public License version 2 and
> > > + * only version 2 as published by the Free Software Foundation.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > > + * GNU General Public License for more details.
> > > + */
> > > +
> > > +#include <linux/clk.h>
> > > +#include <linux/err.h>
> > > +#include <linux/io.h>
> > > +#include <linux/module.h>
> > > +#include <linux/of.h>
> > > +#include <linux/phy/phy.h>
> > > +#include <linux/platform_device.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/regmap.h>
> > > +#include <linux/mfd/syscon.h>
> > > +
> > > +/* USB QSCRATCH Hardware registers */
> > > +#define QSCRATCH_GENERAL_CFG		(0x08)
> > > +#define HSUSB_PHY_CTRL_REG		(0x10)
> > > +
> > > +/* PHY_CTRL_REG */
> > > +#define HSUSB_CTRL_DMSEHV_CLAMP		BIT(24)
> > > +#define HSUSB_CTRL_USB2_SUSPEND		BIT(23)
> > > +#define HSUSB_CTRL_UTMI_CLK_EN		BIT(21)
> > > +#define HSUSB_CTRL_UTMI_OTG_VBUS_VALID	BIT(20)
> > > +#define HSUSB_CTRL_USE_CLKCORE		BIT(18)
> > > +#define HSUSB_CTRL_DPSEHV_CLAMP		BIT(17)
> > > +#define HSUSB_CTRL_COMMONONN		BIT(11)
> > > +#define HSUSB_CTRL_ID_HV_CLAMP		BIT(9)
> > > +#define HSUSB_CTRL_OTGSESSVLD_CLAMP	BIT(8)
> > > +#define HSUSB_CTRL_CLAMP_EN		BIT(7)
> > > +#define HSUSB_CTRL_RETENABLEN		BIT(1)
> > > +#define HSUSB_CTRL_POR			BIT(0)
> > > +
> > > +/* QSCRATCH_GENERAL_CFG */
> > > +#define HSUSB_GCFG_XHCI_REV		BIT(2)
> > > +
> > > +/* USB QSCRATCH Hardware registers */
> > > +#define SSUSB_PHY_CTRL_REG		(0x00)
> > > +#define SSUSB_PHY_PARAM_CTRL_1		(0x04)
> > > +#define SSUSB_PHY_PARAM_CTRL_2		(0x08)
> > > +#define CR_PROTOCOL_DATA_IN_REG		(0x0c)
> > > +#define CR_PROTOCOL_DATA_OUT_REG	(0x10)
> > > +#define CR_PROTOCOL_CAP_ADDR_REG	(0x14)
> > > +#define CR_PROTOCOL_CAP_DATA_REG	(0x18)
> > > +#define CR_PROTOCOL_READ_REG		(0x1c)
> > > +#define CR_PROTOCOL_WRITE_REG		(0x20)
> > > +
> > > +/* PHY_CTRL_REG */
> > > +#define SSUSB_CTRL_REF_USE_PAD		BIT(28)
> > > +#define SSUSB_CTRL_TEST_POWERDOWN	BIT(27)
> > > +#define SSUSB_CTRL_LANE0_PWR_PRESENT	BIT(24)
> > > +#define SSUSB_CTRL_SS_PHY_EN		BIT(8)
> > > +#define SSUSB_CTRL_SS_PHY_RESET		BIT(7)
> > > +
> > > +/* SSPHY control registers - Does this need 0x30? */
> > > +#define SSPHY_CTRL_RX_OVRD_IN_HI(lane)	(0x1006 + 0x100 *
> > (lane))
> > > +#define SSPHY_CTRL_TX_OVRD_DRV_LO(lane)	(0x1002 + 0x100 *
> > (lane))
> > > +
> > > +/* SSPHY SoC version specific values */
> > > +#define SSPHY_RX_EQ_VALUE		4 /* Override value for rx_eq
> > */
> > > +/* Override value for transmit preemphasis */
> > > +#define SSPHY_TX_DEEMPH_3_5DB		23
> > > +/* Override value for mpll */
> > > +#define SSPHY_MPLL_VALUE		0
> > > +
> > > +/* QSCRATCH PHY_PARAM_CTRL1 fields */
> > > +#define PHY_PARAM_CTRL1_TX_FULL_SWING_MASK	GENMASK(26,
> > 19)
> > > +#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK	GENMASK(19,
> > 13)
> > > +#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK	GENMASK(13,
> > 7)
> > > +#define PHY_PARAM_CTRL1_LOS_BIAS_MASK		GENMASK(7,
> > 2)
> > > +
> > > +#define PHY_PARAM_CTRL1_MASK				\
> > > +		(PHY_PARAM_CTRL1_TX_FULL_SWING_MASK |	\
> > > +		 PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK |	\
> > > +		 PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK |	\
> > > +		 PHY_PARAM_CTRL1_LOS_BIAS_MASK)
> > > +
> > > +#define PHY_PARAM_CTRL1_TX_FULL_SWING(x)	\
> > > +		(((x) << 20) & PHY_PARAM_CTRL1_TX_FULL_SWING_MASK)
> > > +#define PHY_PARAM_CTRL1_TX_DEEMPH_6DB(x)	\
> > > +		(((x) << 14) &
> > PHY_PARAM_CTRL1_TX_DEEMPH_6DB_MASK)
> > > +#define PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(x)	\
> > > +		(((x) <<  8) &
> > PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB_MASK)
> > > +#define PHY_PARAM_CTRL1_LOS_BIAS(x)	\
> > > +		(((x) <<  3) & PHY_PARAM_CTRL1_LOS_BIAS_MASK)
> > > +
> > > +/* RX OVRD IN HI bits */
> > > +#define RX_OVRD_IN_HI_RX_RESET_OVRD		BIT(13)
> > > +#define RX_OVRD_IN_HI_RX_RX_RESET		BIT(12)
> > > +#define RX_OVRD_IN_HI_RX_EQ_OVRD		BIT(11)
> > > +#define RX_OVRD_IN_HI_RX_EQ_MASK		GENMASK(10, 7)
> > > +#define RX_OVRD_IN_HI_RX_EQ(x)			((x) << 8)
> > > +#define RX_OVRD_IN_HI_RX_EQ_EN_OVRD		BIT(7)
> > > +#define RX_OVRD_IN_HI_RX_EQ_EN			BIT(6)
> > > +#define RX_OVRD_IN_HI_RX_LOS_FILTER_OVRD	BIT(5)
> > > +#define RX_OVRD_IN_HI_RX_LOS_FILTER_MASK	GENMASK(4, 2)
> > > +#define RX_OVRD_IN_HI_RX_RATE_OVRD		BIT(2)
> > > +#define RX_OVRD_IN_HI_RX_RATE_MASK		GENMASK(2, 0)
> > > +
> > > +/* TX OVRD DRV LO register bits */
> > > +#define TX_OVRD_DRV_LO_AMPLITUDE_MASK		GENMASK(6,
> > 0)
> > > +#define TX_OVRD_DRV_LO_PREEMPH_MASK		GENMASK(13,
> > 6)
> > > +#define TX_OVRD_DRV_LO_PREEMPH(x)		((x) << 7)
> > > +#define TX_OVRD_DRV_LO_EN			BIT(14)
> > > +
> > > +/* MPLL bits */
> > > +#define SSPHY_MPLL_MASK				GENMASK(8,
> > 5)
> > > +#define SSPHY_MPLL(x)				((x) << 5)
> > > +
> > > +/* SS CAP register bits */
> > > +#define SS_CR_CAP_ADDR_REG			BIT(0)
> > > +#define SS_CR_CAP_DATA_REG			BIT(0)
> > > +#define SS_CR_READ_REG				BIT(0)
> > > +#define SS_CR_WRITE_REG				BIT(0)
> > > +
> > > +struct usb_phy {
> > > +	void __iomem		*base;
> > > +	struct device		*dev;
> > > +	struct clk		*xo_clk;
> > > +	struct clk		*ref_clk;
> > > +	u32			rx_eq;
> > > +	u32			tx_deamp_3_5db;
> > > +	u32			mpll;
> > > +};
> > > +
> > > +struct phy_drvdata {
> > > +	struct phy_ops	ops;
> > > +	u32		clk_rate;
> > > +};
> > > +
> > > +/**
> > > + * Write register and read back masked value to confirm it is written
> > > + *
> > > + * @base - QCOM DWC3 PHY base virtual address.
> > > + * @offset - register offset.
> > > + * @mask - register bitmask specifying what should be updated
> > > + * @val - value to write.
> > > + */
> > > +static inline void usb_phy_write_readback(struct usb_phy *phy_dwc3,
> > > +					  u32 offset,
> > > +					  const u32 mask, u32 val)
> > > +{
> > > +	u32 write_val, tmp = readl(phy_dwc3->base + offset);
> > > +
> > > +	tmp &= ~mask;		/* retain other bits */
> > > +	write_val = tmp | val;
> > > +
> > > +	writel(write_val, phy_dwc3->base + offset);
> > > +
> > > +	/* Read back to see if val was written */
> > > +	tmp = readl(phy_dwc3->base + offset);
> > > +	tmp &= mask;		/* clear other bits */
> > > +
> > > +	if (tmp != val)
> > > +		dev_err(phy_dwc3->dev, "write: %x to QSCRATCH: %x
> > FAILED\n",
> > > +			val, offset);
> > > +}
> > > +
> > > +static int wait_for_latch(void __iomem *addr)
> > > +{
> > > +	u32 retry = 10;
> > > +
> > > +	while (true) {
> > > +		if (!readl(addr))
> > > +			break;
> > > +
> > > +		if (--retry == 0)
> > > +			return -ETIMEDOUT;
> > > +
> > > +		usleep_range(10, 20);
> > > +	}
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +/**
> > > + * Write SSPHY register
> > > + *
> > > + * @base - QCOM DWC3 PHY base virtual address.
> > > + * @addr - SSPHY address to write.
> > > + * @val - value to write.
> > > + */
> > > +static int usb_ss_write_phycreg(struct usb_phy *phy_dwc3,
> > > +				u32 addr, u32 val)
> > > +{
> > > +	int ret;
> > > +
> > > +	writel(addr, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG);
> > > +	writel(SS_CR_CAP_ADDR_REG,
> > > +	       phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base +
> > CR_PROTOCOL_CAP_ADDR_REG);
> > > +	if (ret)
> > > +		goto err_wait;
> > > +
> > > +	writel(val, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG);
> > > +	writel(SS_CR_CAP_DATA_REG,
> > > +	       phy_dwc3->base + CR_PROTOCOL_CAP_DATA_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base +
> > CR_PROTOCOL_CAP_DATA_REG);
> > > +	if (ret)
> > > +		goto err_wait;
> > > +
> > > +	writel(SS_CR_WRITE_REG, phy_dwc3->base +
> > CR_PROTOCOL_WRITE_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base +
> > CR_PROTOCOL_WRITE_REG);
> > > +
> > > +err_wait:
> > > +	if (ret)
> > > +		dev_err(phy_dwc3->dev, "timeout waiting for latch\n");
> > > +	return ret;
> > > +}
> > > +
> > > +/**
> > > + * Read SSPHY register.
> > > + *
> > > + * @base - QCOM DWC3 PHY base virtual address.
> > > + * @addr - SSPHY address to read.
> > > + */
> > > +static int usb_ss_read_phycreg(struct usb_phy *phy_dwc3,
> > > +			       u32 addr, u32 *val)
> > > +{
> > > +	int ret;
> > > +
> > > +	writel(addr, phy_dwc3->base + CR_PROTOCOL_DATA_IN_REG);
> > > +	writel(SS_CR_CAP_ADDR_REG,
> > > +	       phy_dwc3->base + CR_PROTOCOL_CAP_ADDR_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base +
> > CR_PROTOCOL_CAP_ADDR_REG);
> > > +	if (ret)
> > > +		goto err_wait;
> > > +
> > > +	/*
> > > +	 * Due to hardware bug, first read of SSPHY register might be
> > > +	 * incorrect. Hence as workaround, SW should perform SSPHY
> > register
> > > +	 * read twice, but use only second read and ignore first read.
> > > +	 */
> > > +	writel(SS_CR_READ_REG, phy_dwc3->base +
> > CR_PROTOCOL_READ_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_READ_REG);
> > > +	if (ret)
> > > +		goto err_wait;
> > > +
> > > +	/* throwaway read */
> > > +	readl(phy_dwc3->base + CR_PROTOCOL_DATA_OUT_REG);
> > > +
> > > +	writel(SS_CR_READ_REG, phy_dwc3->base +
> > CR_PROTOCOL_READ_REG);
> > > +
> > > +	ret = wait_for_latch(phy_dwc3->base + CR_PROTOCOL_READ_REG);
> > > +	if (ret)
> > > +		goto err_wait;
> > > +
> > > +	*val = readl(phy_dwc3->base + CR_PROTOCOL_DATA_OUT_REG);
> > > +
> > > +err_wait:
> > > +	return ret;
> > > +}
> > > +
> > > +static int qcom_ipq806x_usb_hs_phy_init(struct phy *phy)
> > > +{
> > > +	struct usb_phy *phy_dwc3 = phy_get_drvdata(phy);
> > > +	int ret;
> > > +	u32 val;
> > > +
> > > +	ret = clk_prepare_enable(phy_dwc3->xo_clk);
> > > +	if (ret)
> > > +		return ret;
> > > +
> > > +	ret = clk_prepare_enable(phy_dwc3->ref_clk);
> > > +	if (ret) {
> > > +		clk_disable_unprepare(phy_dwc3->xo_clk);
> > > +		return ret;
> > > +	}
> > > +
> > > +	/*
> > > +	 * HSPHY Initialization: Enable UTMI clock, select 19.2MHz fsel
> > > +	 * enable clamping, and disable RETENTION (power-on default is
> > ENABLED)
> > > +	 */
> > > +	val = HSUSB_CTRL_DPSEHV_CLAMP |
> > HSUSB_CTRL_DMSEHV_CLAMP |
> > > +		HSUSB_CTRL_RETENABLEN  | HSUSB_CTRL_COMMONONN |
> > > +		HSUSB_CTRL_OTGSESSVLD_CLAMP |
> > HSUSB_CTRL_ID_HV_CLAMP |
> > > +		HSUSB_CTRL_DPSEHV_CLAMP |
> > HSUSB_CTRL_UTMI_OTG_VBUS_VALID |
> > > +		HSUSB_CTRL_UTMI_CLK_EN | HSUSB_CTRL_CLAMP_EN |
> > 0x70;
> > > +
> > > +	/* use core clock if external reference is not present */
> > > +	if (!phy_dwc3->xo_clk)
> > > +		val |= HSUSB_CTRL_USE_CLKCORE;
> > > +
> > > +	writel(val, phy_dwc3->base + HSUSB_PHY_CTRL_REG);
> > > +	usleep_range(2000, 2200);
> > > +
> > > +	/* Disable (bypass) VBUS and ID filters */
> > > +	writel(HSUSB_GCFG_XHCI_REV, phy_dwc3->base +
> > QSCRATCH_GENERAL_CFG);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static int qcom_ipq806x_usb_hs_phy_exit(struct phy *phy)
> > > +{
> > > +	struct usb_phy *phy_dwc3 = phy_get_drvdata(phy);
> > > +
> > > +	clk_disable_unprepare(phy_dwc3->ref_clk);
> > > +	clk_disable_unprepare(phy_dwc3->xo_clk);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static int qcom_ipq806x_usb_ss_phy_init(struct phy *phy)
> > > +{
> > > +	struct usb_phy *phy_dwc3 = phy_get_drvdata(phy);
> > > +	int ret;
> > > +	u32 data = 0;
> > > +
> > > +	ret = clk_prepare_enable(phy_dwc3->xo_clk);
> > > +	if (ret)
> > > +		return ret;
> > > +
> > > +	ret = clk_prepare_enable(phy_dwc3->ref_clk);
> > > +	if (ret) {
> > > +		clk_disable_unprepare(phy_dwc3->xo_clk);
> > > +		return ret;
> > > +	}
> > > +
> > > +	/* reset phy */
> > > +	data = readl(phy_dwc3->base + SSUSB_PHY_CTRL_REG);
> > > +	writel(data | SSUSB_CTRL_SS_PHY_RESET,
> > > +	       phy_dwc3->base + SSUSB_PHY_CTRL_REG);
> > > +	usleep_range(2000, 2200);
> > > +	writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
> > > +
> > > +	/* clear REF_PAD if we don't have XO clk */
> > > +	if (!phy_dwc3->xo_clk)
> > > +		data &= ~SSUSB_CTRL_REF_USE_PAD;
> > > +	else
> > > +		data |= SSUSB_CTRL_REF_USE_PAD;
> > > +
> > > +	writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
> > > +
> > > +	/* wait for ref clk to become stable, this can take up to 30ms */
> > > +	msleep(30);
> > > +
> > > +	data |= SSUSB_CTRL_SS_PHY_EN |
> > SSUSB_CTRL_LANE0_PWR_PRESENT;
> > > +	writel(data, phy_dwc3->base + SSUSB_PHY_CTRL_REG);
> > > +
> > > +	/*
> > > +	 * WORKAROUND: There is SSPHY suspend bug due to which USB
> > enumerates
> > > +	 * in HS mode instead of SS mode. Workaround it by asserting
> > > +	 * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus
> > mode
> > > +	 */
> > > +	ret = usb_ss_read_phycreg(phy_dwc3, 0x102D, &data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	data |= (1 << 7);
> > > +	ret = usb_ss_write_phycreg(phy_dwc3, 0x102D, data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	ret = usb_ss_read_phycreg(phy_dwc3, 0x1010, &data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	data &= ~0xff0;
> > > +	data |= 0x20;
> > > +	ret = usb_ss_write_phycreg(phy_dwc3, 0x1010, data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	/*
> > > +	 * Fix RX Equalization setting as follows
> > > +	 * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0
> > > +	 * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1
> > > +	 * LANE0.RX_OVRD_IN_HI.RX_EQ set based on SoC version
> > > +	 * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1
> > > +	 */
> > > +	ret = usb_ss_read_phycreg(phy_dwc3,
> > > +				  SSPHY_CTRL_RX_OVRD_IN_HI(0), &data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	data &= ~RX_OVRD_IN_HI_RX_EQ_EN;
> > > +	data |= RX_OVRD_IN_HI_RX_EQ_EN_OVRD;
> > > +	data &= ~RX_OVRD_IN_HI_RX_EQ_MASK;
> > > +	data |= RX_OVRD_IN_HI_RX_EQ(phy_dwc3->rx_eq);
> > > +	data |= RX_OVRD_IN_HI_RX_EQ_OVRD;
> > > +	ret = usb_ss_write_phycreg(phy_dwc3,
> > > +				   SSPHY_CTRL_RX_OVRD_IN_HI(0), data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	/*
> > > +	 * Set EQ and TX launch amplitudes as follows
> > > +	 * LANE0.TX_OVRD_DRV_LO.PREEMPH set based on SoC version
> > > +	 * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 110
> > > +	 * LANE0.TX_OVRD_DRV_LO.EN set to 1.
> > > +	 */
> > > +	ret = usb_ss_read_phycreg(phy_dwc3,
> > > +				  SSPHY_CTRL_TX_OVRD_DRV_LO(0), &data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	data &= ~TX_OVRD_DRV_LO_PREEMPH_MASK;
> > > +	data |= TX_OVRD_DRV_LO_PREEMPH(phy_dwc3-
> > >tx_deamp_3_5db);
> > > +	data &= ~TX_OVRD_DRV_LO_AMPLITUDE_MASK;
> > > +	data |= 0x6E;
> > > +	data |= TX_OVRD_DRV_LO_EN;
> > > +	ret = usb_ss_write_phycreg(phy_dwc3,
> > > +				   SSPHY_CTRL_TX_OVRD_DRV_LO(0), data);
> > > +	if (ret)
> > > +		goto err_phy_trans;
> > > +
> > > +	data = 0;
> > > +	data &= ~SSPHY_MPLL_MASK;
> > > +	data |= SSPHY_MPLL(phy_dwc3->mpll);
> > > +	usb_ss_write_phycreg(phy_dwc3, 0x30, data);
> > > +
> > > +	/*
> > > +	 * Set the QSCRATCH PHY_PARAM_CTRL1 parameters as follows
> > > +	 * TX_FULL_SWING [26:20] amplitude to 110
> > > +	 * TX_DEEMPH_6DB [19:14] to 32
> > > +	 * TX_DEEMPH_3_5DB [13:8] set based on SoC version
> > > +	 * LOS_BIAS [7:3] to 9
> > > +	 */
> > > +	data = readl(phy_dwc3->base + SSUSB_PHY_PARAM_CTRL_1);
> > > +
> > > +	data &= ~PHY_PARAM_CTRL1_MASK;
> > > +
> > > +	data |= PHY_PARAM_CTRL1_TX_FULL_SWING(0x6e) |
> > > +		PHY_PARAM_CTRL1_TX_DEEMPH_6DB(0x20) |
> > > +		PHY_PARAM_CTRL1_TX_DEEMPH_3_5DB(phy_dwc3-
> > >tx_deamp_3_5db) |
> > > +		PHY_PARAM_CTRL1_LOS_BIAS(0x9);
> > > +
> > > +	usb_phy_write_readback(phy_dwc3, SSUSB_PHY_PARAM_CTRL_1,
> > > +			       PHY_PARAM_CTRL1_MASK, data);
> > > +
> > > +err_phy_trans:
> > > +	return ret;
> > > +}
> > > +
> > > +static int qcom_ipq806x_usb_ss_phy_exit(struct phy *phy)
> > > +{
> > > +	struct usb_phy *phy_dwc3 = phy_get_drvdata(phy);
> > > +
> > > +	/* Sequence to put SSPHY in low power state:
> > > +	 * 1. Clear REF_PHY_EN in PHY_CTRL_REG
> > > +	 * 2. Clear REF_USE_PAD in PHY_CTRL_REG
> > > +	 * 3. Set TEST_POWERED_DOWN in PHY_CTRL_REG to enable PHY
> > retention
> > > +	 */
> > > +	usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
> > > +			       SSUSB_CTRL_SS_PHY_EN, 0x0);
> > > +	usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
> > > +			       SSUSB_CTRL_REF_USE_PAD, 0x0);
> > > +	usb_phy_write_readback(phy_dwc3, SSUSB_PHY_CTRL_REG,
> > > +			       SSUSB_CTRL_TEST_POWERDOWN, 0x0);
> > > +
> > > +	clk_disable_unprepare(phy_dwc3->ref_clk);
> > > +	clk_disable_unprepare(phy_dwc3->xo_clk);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static const struct phy_drvdata qcom_ipq806x_usb_hs_drvdata = {
> > > +	.ops = {
> > > +		.init		= qcom_ipq806x_usb_hs_phy_init,
> > > +		.exit		= qcom_ipq806x_usb_hs_phy_exit,
> > > +		.owner		= THIS_MODULE,
> > > +	},
> > > +	.clk_rate = 60000000,
> > > +};
> > > +
> > > +static const struct phy_drvdata qcom_ipq806x_usb_ss_drvdata = {
> > > +	.ops = {
> > > +		.init		= qcom_ipq806x_usb_ss_phy_init,
> > > +		.exit		= qcom_ipq806x_usb_ss_phy_exit,
> > > +		.owner		= THIS_MODULE,
> > > +	},
> > > +	.clk_rate = 125000000,
> > > +};
> > > +
> > > +static const struct of_device_id qcom_ipq806x_usb_phy_table[] = {
> > > +	{ .compatible = "qcom,ipq806x-usb-phy-hs",
> > > +	  .data = &qcom_ipq806x_usb_hs_drvdata },
> > > +	{ .compatible = "qcom,ipq806x-usb-phy-ss",
> > > +	  .data = &qcom_ipq806x_usb_ss_drvdata },
> > > +	{ /* Sentinel */ }
> > > +};
> > > +MODULE_DEVICE_TABLE(of, qcom_ipq806x_usb_phy_table);
> > > +
> > > +static int qcom_ipq806x_usb_phy_probe(struct platform_device *pdev)
> > > +{
> > > +	struct usb_phy	*phy_dwc3;
> > > +	struct phy_provider		*phy_provider;
> > > +	struct phy			*generic_phy;
> > > +	const struct of_device_id *match;
> > > +	const struct phy_drvdata *data;
> > > +	struct resource			*res;
> > > +	resource_size_t			size;
> > > +	struct device_node *np;
> > > +
> > > +	phy_dwc3 = devm_kzalloc(&pdev->dev, sizeof(*phy_dwc3),
> > GFP_KERNEL);
> > > +	if (!phy_dwc3)
> > > +		return -ENOMEM;
> > > +
> > > +	match = of_match_node(qcom_ipq806x_usb_phy_table, pdev-
> > >dev.of_node);
> > > +	data = match->data;
> > > +
> > > +	phy_dwc3->dev = &pdev->dev;
> > > +
> > > +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > > +	if (!res)
> > > +		return -EINVAL;
> > > +	size = resource_size(res);
> > > +	phy_dwc3->base = devm_ioremap(phy_dwc3->dev, res->start,
> > size);
> > > +
> > > +	if (IS_ERR(phy_dwc3->base)) {
> > > +		dev_err(phy_dwc3->dev, "failed to map reg\n");
> > > +		return PTR_ERR(phy_dwc3->base);
> > > +	}
> > > +
> > > +	phy_dwc3->ref_clk = devm_clk_get(phy_dwc3->dev, "ref");
> > > +	if (IS_ERR(phy_dwc3->ref_clk)) {
> > > +		dev_dbg(phy_dwc3->dev, "cannot get reference clock\n");
> > > +		return PTR_ERR(phy_dwc3->ref_clk);
> > > +	}
> > > +
> > > +	clk_set_rate(phy_dwc3->ref_clk, data->clk_rate);
> > > +
> > > +	phy_dwc3->xo_clk = devm_clk_get(phy_dwc3->dev, "xo");
> > > +	if (IS_ERR(phy_dwc3->xo_clk)) {
> > > +		dev_dbg(phy_dwc3->dev, "cannot get TCXO clock\n");
> > > +		phy_dwc3->xo_clk = NULL;
> > > +	}
> > > +
> > > +	/* Parse device node to probe HSIO settings */
> > > +	np = of_node_get(pdev->dev.of_node);
> > > +	if (!of_compat_cmp(match->compatible, "qcom,ipq806x-usb-phy-
> > ss",
> > > +			   strlen(match->compatible))) {
> > > +		if (of_property_read_u32(np, "qcom,rx-eq", &phy_dwc3-
> > >rx_eq) ||
> > > +		    of_property_read_u32(np, "qcom,tx-deamp_3_5db",
> > > +					 &phy_dwc3->tx_deamp_3_5db) ||
> > > +		    of_property_read_u32(np, "qcom,mpll", &phy_dwc3-
> > >mpll)) {
> > > +			dev_err(phy_dwc3->dev, "cannot get HSIO settings
> > from device node, using default values\n");
> > > +
> > > +			/* Default HSIO settings */
> > > +			phy_dwc3->rx_eq = SSPHY_RX_EQ_VALUE;
> > > +			phy_dwc3->tx_deamp_3_5db =
> > SSPHY_TX_DEEMPH_3_5DB;
> > > +			phy_dwc3->mpll = SSPHY_MPLL_VALUE;
> > > +		}
> > > +	}
> > > +
> > > +	generic_phy = devm_phy_create(phy_dwc3->dev, pdev-
> > >dev.of_node,
> > > +				      &data->ops);
> > > +
> > > +	if (IS_ERR(generic_phy))
> > > +		return PTR_ERR(generic_phy);
> > > +
> > > +	phy_set_drvdata(generic_phy, phy_dwc3);
> > > +	platform_set_drvdata(pdev, phy_dwc3);
> > > +
> > > +	phy_provider = devm_of_phy_provider_register(phy_dwc3->dev,
> > > +						     of_phy_simple_xlate);
> > > +
> > > +	if (IS_ERR(phy_provider))
> > > +		return PTR_ERR(phy_provider);
> > > +
> > > +	return 0;
> > > +}
> > > +
> > > +static struct platform_driver qcom_ipq806x_usb_phy_driver = {
> > > +	.probe		= qcom_ipq806x_usb_phy_probe,
> > > +	.driver		= {
> > > +		.name	= "qcom-ipq806x-usb-phy",
> > > +		.owner	= THIS_MODULE,
> > > +		.of_match_table = qcom_ipq806x_usb_phy_table,
> > > +	},
> > > +};
> > > +
> > > +module_platform_driver(qcom_ipq806x_usb_phy_driver);
> > > +
> > > +MODULE_ALIAS("platform:phy-qcom-ipq806x-usb");
> > > +MODULE_LICENSE("GPL v2");
> > > +MODULE_AUTHOR("Andy Gross <agross@xxxxxxxxxxxxxx>");
> > > +MODULE_AUTHOR("Ivan T. Ivanov <iivanov@xxxxxxxxxx>");
> > > +MODULE_DESCRIPTION("DesignWare USB3 QCOM PHY driver");
> > > --
> > > 2.25.1

J.

-- 
] https://www.earth.li/~noodles/ []   101 things you can't have too    [
]  PGP/GPG Key @ the.earth.li    []      much of : 34 - Beaches.       [
] via keyserver, web or email.   []                                    [
] RSA: 4096/0x94FA372B2DA8B985   []                                    [



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux