On Tue, Jun 02, 2020 at 08:04:16PM +0300, Andy Shevchenko wrote:
> On Tue, Jun 2, 2020 at 7:49 PM Tomasz Duszynski
> <tomasz.duszynski@xxxxxxxxxxx> wrote:
> >
> > Add serial interface driver for the SCD30 sensor.
>
> ...
>
> > +static u16 scd30_serdev_cmd_lookup_tbl[] = {
> > + [CMD_START_MEAS] = 0x0036,
> > + [CMD_STOP_MEAS] = 0x0037,
> > + [CMD_MEAS_INTERVAL] = 0x0025,
> > + [CMD_MEAS_READY] = 0x0027,
> > + [CMD_READ_MEAS] = 0x0028,
> > + [CMD_ASC] = 0x003a,
> > + [CMD_FRC] = 0x0039,
> > + [CMD_TEMP_OFFSET] = 0x003b,
> > + [CMD_FW_VERSION] = 0x0020,
> > + [CMD_RESET] = 0x0034,
>
> Hmm... Can't we keep them ordered by value?
>
> > +};
>
> ...
>
> > + ret = wait_for_completion_interruptible_timeout(&priv->meas_ready,
> > + SCD30_SERDEV_TIMEOUT);
> > + if (ret > 0)
> > + ret = 0;
> > + else if (!ret)
> > + ret = -ETIMEDOUT;
> > +
> > + return ret;
>
> Perhaps
>
> if (ret < 0)
> return ret;
> if (ret == 0)
> return -ETIMEDOUT;
> return 0;
>
> ?
Matter of style but since I will be doing other changes I can touch that
too.
>
> ...
>
> > + char txbuf[SCD30_SERDEV_MAX_BUF_SIZE] = { SCD30_SERDEV_ADDR },
> > + rxbuf[SCD30_SERDEV_MAX_BUF_SIZE], *rsp = response;
>
> Please, apply type to each variable separately.
>
Fine.
> ...
>
> > + switch (txbuf[1]) {
> > + case SCD30_SERDEV_WRITE:
>
> > + if (memcmp(txbuf, txbuf, txsize)) {
>
> I'm not sure I understand this.
>
Ah, thanks for catching this. tx should be compared to rx.
> > + dev_err(state->dev, "wrong message received\n");
> > + return -EIO;
> > + }
> > + break;
> > + case SCD30_SERDEV_READ:
>
> > + if (rxbuf[2] != (rxsize -
> > + SCD30_SERDEV_RX_HEADER_SIZE -
> > + SCD30_SERDEV_CRC_SIZE)) {
>
> Perhaps you can come up with better indentation/ line split?
>
I'd rather leave it as is.
> > + dev_err(state->dev,
> > + "received data size does not match header\n");
> > + return -EIO;
> > + }
> > +
> > + rxsize -= SCD30_SERDEV_CRC_SIZE;
> > + crc = get_unaligned_le16(rxbuf + rxsize);
> > + if (crc != scd30_serdev_calc_crc(rxbuf, rxsize)) {
> > + dev_err(state->dev, "data integrity check failed\n");
> > + return -EIO;
> > + }
> > +
> > + rxsize -= SCD30_SERDEV_RX_HEADER_SIZE;
> > + memcpy(rsp, rxbuf + SCD30_SERDEV_RX_HEADER_SIZE, rxsize);
> > + break;
> > + default:
> > + dev_err(state->dev, "received unknown op code\n");
> > + return -EIO;
> > + }
> > +
> > + return 0;
> > +}
>
> ...
>
> > +static struct serdev_device_driver scd30_serdev_driver = {
> > + .driver = {
>
> > + .name = KBUILD_MODNAME,
>
> This is not the best what we can do. The name is an ABI and better if
> it will be constant (independent on file name).
>
> > + .of_match_table = scd30_serdev_of_match,
> > + .pm = &scd30_pm_ops,
> > + },
> > + .probe = scd30_serdev_probe,
> > +};
>
> --
> With Best Regards,
> Andy Shevchenko
