Hi,
This series convert the adi,adv7511.txt DT bindings to json-schema. As a
result of the conversion some dts files needed to be updated.
The changes to the dts files are of three types:
- Reordering of the I2C slave addresses list of the ADV75xx node. The
addresses in the 'reg' property and the matching names in
'reg-names' for an I2C slave don't need to be in any particular
order, but the DT schema defines these properties as a cell array
and a string array respectively, which are ordered, so the
definitions in the dts files must match the order in the binding.
- Filling the minimum binding requirements. Most of the time this
means creating a 'ports' node in the boards that don't define
them. Note, however, that the purpose of this is simply to make the
definition compliant with the binding. I didn't define any endpoints
for the ports.
- Removing unneeded properties.
About the binding conversion:
- The original binding covered five different devices: ADV7511,
ADV7511W, ADV7513, ADV7533 and ADV7535. They all share a common set
of properties but ADV7533 and ADV7535 have enough differences from
the rest to warrant their own binding file. In v1 I modelled all the
properties constraints for all five devices in a single file but it
turned out a bit too complex. Splitting the binding into one for
ADV7511/11W/13 and another for ADV7533/35 makes them much easier to
read and maintain.
Patches 1/4 to 3/4 contain the dts changes. Patch 4/4 contains the
binding conversion.
NOTE: the bindings have been tested with:
make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>
make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7533.yaml>
for <arch> = arm and arm64. dts changes haven't been tested in hardware.
Some existing DTs are expected to fail after this conversion.
Changes in v3:
- Removed from the patch series (already in mainline):
- arm64: dts: renesas: make hdmi encoder nodes compliant with DT bindings
- ARM: dts: renesas: make hdmi encoder nodes compliant with DT bindings
- ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39
- Additional DTs fixes:
- boot/dts/stm32mp15xx-dhcor-avenger96.dtsi.
- [Laurent] adi,adv7511.yaml and adi,adv7533.yaml.
- Documentation fixes and typos.
- Removed unnecessary allOf's.
- adi,embedded-sync data type changed to boolean.
- Power supplies defined as required.
- Examples updated.
Ricardo Cañuelo (4):
ARM: dts: zynq: add port definitions to hdmi-tx@39
arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT
binding
ARM: dts: stm32: make hdmi-transmitter node compliant with DT bindings
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
.../bindings/display/bridge/adi,adv7511.txt | 143 -----------
.../bindings/display/bridge/adi,adv7511.yaml | 231 ++++++++++++++++++
.../bindings/display/bridge/adi,adv7533.yaml | 175 +++++++++++++
.../boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 6 +-
arch/arm/boot/dts/zynq-zc702.dts | 10 +
arch/arm/boot/dts/zynq-zc706.dts | 10 +
.../boot/dts/hisilicon/hi3660-hikey960.dts | 11 +
.../arm64/boot/dts/hisilicon/hi6220-hikey.dts | 2 +-
8 files changed, 440 insertions(+), 148 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
--
2.18.0
