On 20-05-26 16:50:51, Mike Looijmans wrote:
> This enables support for VBUS on boards where the power is supplied
> by a regulator. The regulator is enabled when the USB port enters
> HOST mode.
>
Why you don't do this at your host controller driver?
Peter
> Signed-off-by: Mike Looijmans <mike.looijmans@xxxxxxxx>
> ---
> .../devicetree/bindings/usb/usb-nop-xceiv.txt | 3 ++
> drivers/usb/phy/phy-generic.c | 44 ++++++++++++++++++-
> drivers/usb/phy/phy-generic.h | 2 +
> 3 files changed, 48 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
> index 4dc6a8ee3071..775a19fdb613 100644
> --- a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
> +++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
> @@ -16,6 +16,9 @@ Optional properties:
>
> - vcc-supply: phandle to the regulator that provides power to the PHY.
>
> +- vbus-supply: phandle to the regulator that provides the VBUS power for when
> + the device is in HOST mode.
> +
> - reset-gpios: Should specify the GPIO for reset.
>
> - vbus-detect-gpio: should specify the GPIO detecting a VBus insertion
> diff --git a/drivers/usb/phy/phy-generic.c b/drivers/usb/phy/phy-generic.c
> index 661a229c105d..ebfb90764511 100644
> --- a/drivers/usb/phy/phy-generic.c
> +++ b/drivers/usb/phy/phy-generic.c
> @@ -203,13 +203,43 @@ static int nop_set_host(struct usb_otg *otg, struct usb_bus *host)
> return 0;
> }
>
> +static int nop_set_vbus(struct usb_otg *otg, bool enabled)
> +{
> + struct usb_phy_generic *nop;
> + int ret;
> +
> + if (!otg)
> + return -ENODEV;
> +
> + nop = container_of(otg->usb_phy, struct usb_phy_generic, phy);
> +
> + if (!nop->vbus_reg)
> + return 0;
> +
> + if (enabled) {
> + if (nop->vbus_reg_enabled)
> + return 0;
> + ret = regulator_enable(nop->vbus_reg);
> + if (ret < 0)
> + return ret;
> + nop->vbus_reg_enabled = true;
> + } else {
> + if (!nop->vbus_reg_enabled)
> + return 0;
> + ret = regulator_disable(nop->vbus_reg);
> + if (ret < 0)
> + return ret;
> + nop->vbus_reg_enabled = false;
> + }
> +}
> +
> int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
> {
> enum usb_phy_type type = USB_PHY_TYPE_USB2;
> int err = 0;
>
> u32 clk_rate = 0;
> - bool needs_vcc = false, needs_clk = false;
> + bool needs_vcc = false, needs_clk = false, needs_vbus = false;
>
> if (dev->of_node) {
> struct device_node *node = dev->of_node;
> @@ -219,6 +249,7 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
>
> needs_vcc = of_property_read_bool(node, "vcc-supply");
> needs_clk = of_property_read_bool(node, "clocks");
> + needs_vbus = of_property_read_bool(node, "vbus-supply");
> }
> nop->gpiod_reset = devm_gpiod_get_optional(dev, "reset",
> GPIOD_ASIS);
> @@ -268,6 +299,16 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
> return -EPROBE_DEFER;
> }
>
> + nop->vbus_reg = devm_regulator_get(dev, "vbus");
> + if (IS_ERR(nop->vbus_reg)) {
> + dev_dbg(dev, "Error getting vbus regulator: %ld\n",
> + PTR_ERR(nop->vbus_reg));
> + if (needs_vbus)
> + return -EPROBE_DEFER;
> +
> + nop->vbus_reg = NULL;
> + }
> +
> nop->dev = dev;
> nop->phy.dev = nop->dev;
> nop->phy.label = "nop-xceiv";
> @@ -278,6 +319,7 @@ int usb_phy_gen_create_phy(struct device *dev, struct usb_phy_generic *nop)
> nop->phy.otg->usb_phy = &nop->phy;
> nop->phy.otg->set_host = nop_set_host;
> nop->phy.otg->set_peripheral = nop_set_peripheral;
> + nop->phy.otg->set_vbus = nop_set_vbus;
>
> return 0;
> }
> diff --git a/drivers/usb/phy/phy-generic.h b/drivers/usb/phy/phy-generic.h
> index 7ee80211a688..a3663639ea1e 100644
> --- a/drivers/usb/phy/phy-generic.h
> +++ b/drivers/usb/phy/phy-generic.h
> @@ -14,7 +14,9 @@ struct usb_phy_generic {
> struct gpio_desc *gpiod_reset;
> struct gpio_desc *gpiod_vbus;
> struct regulator *vbus_draw;
> + struct regulator *vbus_reg;
> bool vbus_draw_enabled;
> + bool vbus_reg_enabled;
> unsigned long mA;
> unsigned int vbus;
> };
> --
> 2.17.1
>
--
Thanks,
Peter Chen
