Currently Intel Baytrail I2C semaphore is a feature of the DW APB I2C platform driver. It's a bit confusing to see it's config in the menu at some separated place with no reference to the platform code. Let's move the config definition to be below the I2C_DESIGNWARE_PLATFORM config and mark it with "depends on I2C_DESIGNWARE_PLATFORM" statement. By doing so the config menu will display the feature right below the DW I2C platform driver item and will indent it to the right so signifying its belonging. Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> Cc: Alexey Malahov <Alexey.Malahov@xxxxxxxxxxxxxxxxxxxx> Cc: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx> Cc: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx> Cc: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx> Cc: Rob Herring <robh+dt@xxxxxxxxxx> Cc: linux-mips@xxxxxxxxxxxxxxx Cc: devicetree@xxxxxxxxxxxxxxx --- Changelog v3: - Replace if-endif clause around the I2C_DESIGNWARE_BAYTRAIL config with "depends on" operator. --- drivers/i2c/busses/Kconfig | 25 +++++++++++++------------ 1 file changed, 13 insertions(+), 12 deletions(-) diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index b907d4046942..4e1997642e73 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -538,6 +538,19 @@ config I2C_DESIGNWARE_PLATFORM This driver can also be built as a module. If so, the module will be called i2c-designware-platform. +config I2C_DESIGNWARE_BAYTRAIL + bool "Intel Baytrail I2C semaphore support" + depends on ACPI + depends on I2C_DESIGNWARE_PLATFORM + depends on (I2C_DESIGNWARE_PLATFORM=m && IOSF_MBI) || \ + (I2C_DESIGNWARE_PLATFORM=y && IOSF_MBI=y) + help + This driver enables managed host access to the PMIC I2C bus on select + Intel BayTrail platforms using the X-Powers AXP288 PMIC. It allows + the host to request uninterrupted access to the PMIC's I2C bus from + the platform firmware controlling it. You should say Y if running on + a BayTrail system using the AXP288. + config I2C_DESIGNWARE_SLAVE bool "Synopsys DesignWare Slave" depends on I2C_DESIGNWARE_CORE @@ -560,18 +573,6 @@ config I2C_DESIGNWARE_PCI This driver can also be built as a module. If so, the module will be called i2c-designware-pci. -config I2C_DESIGNWARE_BAYTRAIL - bool "Intel Baytrail I2C semaphore support" - depends on ACPI - depends on (I2C_DESIGNWARE_PLATFORM=m && IOSF_MBI) || \ - (I2C_DESIGNWARE_PLATFORM=y && IOSF_MBI=y) - help - This driver enables managed host access to the PMIC I2C bus on select - Intel BayTrail platforms using the X-Powers AXP288 PMIC. It allows - the host to request uninterrupted access to the PMIC's I2C bus from - the platform firmware controlling it. You should say Y if running on - a BayTrail system using the AXP288. - config I2C_DIGICOLOR tristate "Conexant Digicolor I2C driver" depends on ARCH_DIGICOLOR || COMPILE_TEST -- 2.26.2
