Re: [PATCH 2/2] spi: Add Baikal-T1 System Boot SPI Controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, May 18, 2020 at 04:19:47PM +0100, Mark Brown wrote:
> On Mon, May 18, 2020 at 03:05:42AM +0300, Serge Semin wrote:
> > On Mon, May 11, 2020 at 10:25:06PM +0100, Mark Brown wrote:
> 
> > > Yes, some flags should work here - the issue was that at least some
> > > controllers may end up trying to do multiple SPI operations for one
> > > spi-mem thing which will break if the chip select doesn't get changed to
> > > correspond with what's going on.
> 
> > Ok. New SPI flag it is then. It will be something like this:
> > + #define SPI_CONTROLLER_FLASH_SS		BIT(6)
> 
> I'd rather use CS than SS (it's more common in the code).

Ok.

> 
> > So, what do you think?
> 
> Should be fine, controllers that have an issue implementing just
> shouldn't set the flag.

Yes, exactly what I intended.

> 
> > > > > It's not clear to me that this hardware actually supports spi_mem in
> > > > > hardware?
> 
> > > > SPI-mem operations are implemented by means of the EEPROM-read and Tx-only
> > > > modes of the controller.
> 
> > > Sure, but those seem like normal SPI-level things rather than cases
> > > where the hardware understands that it has a flash attached and is doing
> > > flash specific things.
> 
> > No, hardware can't detect whether the flash is attached. This must be defined by
> > the platform, like based on the DT sub-nodes.
> 
> This isn't about autodetection, it's about the abstraction level the
> hardware is operating on - some hardware is able to generate flash
> operations by itself (possibly with some help programming the opcodes
> that are needed by a given flash), some hardware just works at the
> bytestream level.
> 
> > > A very common case for this stuff is that
> > > controllers have acceleration blocks for read and fall back on normal
> > > SPI for writes and erases, that sounds like what's going on here.
> > 
> > Well, yeah, they do provide some acceleration. EEPROM-read provides automatic
> > write-cmd-dummy-data-then-read operations. But in this case the only thing we
> > have to push into the SPI Tx FIFO is command and dummy bytes. The read operation
> 
> So it's a write then read but you have to program the write each time?

Here is what we need to do to perform the EEPROM-read operation:
1) Enable EEPROM-read mode.
2) Initialize a corresponding registers with a number of SPI transfer words
   (with bits-per-word taken into account) to read.
3) Push opcode + address + dummy bytes into the Tx FIFO. When it's done and
   the Tx FIFO is empty, the controller will proceed with read operations by
   pushing zeros (or ones, don't remember what level it's by default) to MOSI
   and pulling data from MISO into the RX FIFO.
4) Keep up with getting data from the Rx FIFO so one wouldn't get overflown.

Regarding programming write each time. Well, it's up to the driver implementation.
If opcode, address, dummy bytes and number of words to read are the same as before,
then re-programming isn't required.

-Sergey



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux