Set reset gpio to high on ak8975_power_on, set reset gpio to low on
ak8975_power_off.
Without setting it to high on ak8975_power_on driver's probe fails
on ak8975_who_i_am while checking for device identity for AK09911 chip
AK09911 has a reset gpio to handle register's reset. If reset gpio is
set to low it will trigger the reset. AK09911 datasheed says that if not
used reset pin should be connected to VID and this patch emulates this
situation
Signed-off-by: Jonathan Albrieux <jonathan.albrieux@xxxxxxxxx>
---
drivers/iio/magnetometer/ak8975.c | 21 +++++++++++++++++++--
1 file changed, 19 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/magnetometer/ak8975.c b/drivers/iio/magnetometer/ak8975.c
index 3c881541ae72..c1ba5cd2cb6c 100644
--- a/drivers/iio/magnetometer/ak8975.c
+++ b/drivers/iio/magnetometer/ak8975.c
@@ -358,6 +358,7 @@ struct ak8975_data {
u8 asa[3];
long raw_to_gauss[3];
struct gpio_desc *eoc_gpiod;
+ struct gpio_desc *reset_gpiod;
int eoc_irq;
wait_queue_head_t data_ready_queue;
unsigned long flags;
@@ -384,10 +385,13 @@ static int ak8975_power_on(const struct ak8975_data *data)
"Failed to enable specified Vid supply\n");
return ret;
}
+
+ gpiod_set_value_cansleep(data->reset_gpiod, 0);
+
/*
- * According to the datasheet the power supply rise time i 200us
+ * According to the datasheet the power supply rise time is 200us
* and the minimum wait time before mode setting is 100us, in
- * total 300 us. Add some margin and say minimum 500us here.
+ * total 300us. Add some margin and say minimum 500us here.
*/
usleep_range(500, 1000);
return 0;
@@ -396,6 +400,8 @@ static int ak8975_power_on(const struct ak8975_data *data)
/* Disable attached power regulator if any. */
static void ak8975_power_off(const struct ak8975_data *data)
{
+ gpiod_set_value_cansleep(data->reset_gpiod, 1);
+
regulator_disable(data->vid);
regulator_disable(data->vdd);
}
@@ -839,6 +845,7 @@ static int ak8975_probe(struct i2c_client *client,
struct ak8975_data *data;
struct iio_dev *indio_dev;
struct gpio_desc *eoc_gpiod;
+ struct gpio_desc *reset_gpiod;
const void *match;
unsigned int i;
int err;
@@ -856,6 +863,15 @@ static int ak8975_probe(struct i2c_client *client,
if (eoc_gpiod)
gpiod_set_consumer_name(eoc_gpiod, "ak_8975");
+ /*
+ * If reset pin is provided then will be set to high on power on
+ * and to low on power off according to AK09911 datasheet
+ */
+ reset_gpiod = devm_gpiod_get_optional(&client->dev,
+ "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(reset_gpiod))
+ return PTR_ERR(reset_gpiod);
+
/* Register with IIO */
indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
if (indio_dev == NULL)
@@ -866,6 +882,7 @@ static int ak8975_probe(struct i2c_client *client,
data->client = client;
data->eoc_gpiod = eoc_gpiod;
+ data->reset_gpiod = reset_gpiod;
data->eoc_irq = 0;
err = iio_read_mount_matrix(&client->dev, "mount-matrix", &data->orientation);
--
2.17.1
