Hi Pawel Dembicki,
> This patch adds dts for the Check Point L-50 from 600/1100 series
> routers.
>
> Specification:
> -CPU: Marvell Kirkwood 88F6821 1200MHz
> -RAM: 512MB
> -Flash: NAND 512MB
> -WiFi: mPCIe card based on Atheros AR9287 b/g/n
> -WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
> -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+3))
> -USB: 2x USB2.0
> -Express card slot
> -SD card slot
> -Serial console: RJ-45 115200 8n1
> -Unsupported DSL
>
> Signed-off-by: Pawel Dembicki <paweldembicki@xxxxxxxxx>
Applied on mvebu/dt. I think the first patch should be applied by the
device tree maintainers.
Thanks,
Gregory
> ---
> Changes in v2:
> - none
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/kirkwood-l-50.dts | 441 ++++++++++++++++++++++++++++
> 2 files changed, 442 insertions(+)
> create mode 100644 arch/arm/boot/dts/kirkwood-l-50.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e8dd99201397..eba030b3ba69 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -279,6 +279,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
> kirkwood-iomega_ix2_200.dtb \
> kirkwood-is2.dtb \
> kirkwood-km_kirkwood.dtb \
> + kirkwood-l-50.dtb \
> kirkwood-laplug.dtb \
> kirkwood-linkstation-lsqvl.dtb \
> kirkwood-linkstation-lsvl.dtb \
> diff --git a/arch/arm/boot/dts/kirkwood-l-50.dts b/arch/arm/boot/dts/kirkwood-l-50.dts
> new file mode 100644
> index 000000000000..ab3a90287260
> --- /dev/null
> +++ b/arch/arm/boot/dts/kirkwood-l-50.dts
> @@ -0,0 +1,441 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Check Point L-50 Board Description
> + * Copyright 2020 Pawel Dembicki <paweldembicki@xxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "kirkwood.dtsi"
> +#include "kirkwood-6281.dtsi"
> +
> +/ {
> + model = "Check Point L-50";
> + compatible = "checkpoint,l-50", "marvell,kirkwood-88f6281", "marvell,kirkwood";
> +
> + memory {
> + device_type = "memory";
> + reg = <0x00000000 0x20000000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200n8";
> + stdout-path = &uart0;
> + };
> +
> + ocp@f1000000 {
> + pinctrl: pin-controller@10000 {
> + pinctrl-0 = <&pmx_led38 &pmx_sysrst &pmx_button29>;
> + pinctrl-names = "default";
> +
> + pmx_sysrst: pmx-sysrst {
> + marvell,pins = "mpp6";
> + marvell,function = "sysrst";
> + };
> +
> + pmx_button29: pmx_button29 {
> + marvell,pins = "mpp29";
> + marvell,function = "gpio";
> + };
> +
> + pmx_led38: pmx_led38 {
> + marvell,pins = "mpp38";
> + marvell,function = "gpio";
> + };
> +
> + pmx_sdio_cd: pmx-sdio-cd {
> + marvell,pins = "mpp46";
> + marvell,function = "gpio";
> + };
> + };
> +
> + serial@12000 {
> + status = "okay";
> + };
> +
> + mvsdio@90000 {
> + status = "okay";
> + cd-gpios = <&gpio1 14 9>;
> + };
> +
> + i2c@11000 {
> + status = "okay";
> + clock-frequency = <400000>;
> +
> + gpio2: gpio-expander@20{
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + compatible = "semtech,sx1505q";
> + reg = <0x20>;
> +
> + gpio-controller;
> + };
> +
> + /* Three GPIOs from 0x21 exp. are undescribed in dts:
> + * 1: DSL module reset (active low)
> + * 5: mPCIE reset (active low)
> + * 6: Express card reset (active low)
> + */
> + gpio3: gpio-expander@21{
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + compatible = "semtech,sx1505q";
> + reg = <0x21>;
> +
> + gpio-controller;
> + };
> +
> + rtc@30 {
> + compatible = "s35390a";
> + reg = <0x30>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + status_green {
> + label = "l-50:green:status";
> + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
> + };
> +
> + status_orange {
> + label = "l-50:orange:status";
> + gpios = <&gpio3 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi {
> + label = "l-50:green:wifi";
> + gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "phy0tpt";
> + };
> +
> + internet_green {
> + label = "l-50:green:internet";
> + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
> + };
> +
> + internet_red {
> + label = "l-50:red:internet";
> + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + usb1_green {
> + label = "l-50:green:usb1";
> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "usbport";
> + trigger-sources = <&hub_port3>;
> + };
> +
> + usb1_red {
> + label = "l-50:red:usb1";
> + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
> + };
> +
> + usb2_green {
> + label = "l-50:green:usb2";
> + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "usbport";
> + trigger-sources = <&hub_port1>;
> + };
> +
> + usb2_red {
> + label = "l-50:red:usb2";
> + gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + usb2_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "usb2_pwr";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
> + enable-active-low;
> + regulator-always-on;
> + };
> +
> + usb1_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "usb1_pwr";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 4 GPIO_ACTIVE_LOW>;
> + enable-active-low;
> + regulator-always-on;
> + };
> +
> + mpcie_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "mpcie_pwr";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + express_card_pwr {
> + compatible = "regulator-fixed";
> + regulator-name = "express_card_pwr";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-always-on;
> + };
> +
> + keys {
> + compatible = "gpio-keys-polled";
> + poll-interval = <20>;
> +
> + factory_defaults {
> + label = "factory_defaults";
> + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + };
> +};
> +
> +&mdio {
> + status = "okay";
> +
> + ethphy0: ethernet-phy@8 {
> + reg = <0x08>;
> + };
> +
> + switch0: switch@10 {
> + compatible = "marvell,mv88e6085";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x10>;
> + dsa,member = <0 0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + label = "lan5";
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "lan1";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "lan6";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "lan2";
> + };
> +
> + port@4 {
> + reg = <4>;
> + label = "lan7";
> + };
> +
> + switch0port5: port@5 {
> + reg = <5>;
> + phy-mode = "rgmii-txid";
> + link = <&switch1port5>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "cpu";
> + phy-mode = "rgmii-id";
> + ethernet = <ð1port>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> + };
> + };
> + switch@11 {
> + compatible = "marvell,mv88e6085";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x11>;
> + dsa,member = <0 1>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + label = "lan3";
> + };
> +
> + port@1 {
> + reg = <1>;
> + label = "lan8";
> + };
> +
> + port@2 {
> + reg = <2>;
> + label = "lan4";
> + };
> +
> + port@3 {
> + reg = <3>;
> + label = "dmz";
> + };
> +
> + switch1port5: port@5 {
> + reg = <5>;
> + phy-mode = "rgmii-txid";
> + link = <&switch0port5>;
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> + };
> +
> + port@6 {
> + reg = <6>;
> + label = "dsl";
> + fixed-link {
> + speed = <100>;
> + full-duplex;
> + };
> + };
> + };
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> + ethernet0-port@0 {
> + phy-handle = <ðphy0>;
> + };
> +};
> +
> +ð1 {
> + status = "okay";
> + ethernet1-port@0 {
> + speed = <1000>;
> + duplex = <1>;
> + };
> +};
> +
> +&nand {
> + status = "okay";
> + pinctrl-0 = <&pmx_nand>;
> + pinctrl-names = "default";
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0000000 0xc0000>;
> + };
> +
> + partition@a0000 {
> + label = "bootldr-env";
> + reg = <0x000c0000 0x40000>;
> + };
> +
> + partition@100000 {
> + label = "kernel-1";
> + reg = <0x00100000 0x800000>;
> + };
> +
> + partition@900000 {
> + label = "rootfs-1";
> + reg = <0x08200000 0x7100000>;
> + };
> +
> + partition@7a00000 {
> + label = "kernel-2";
> + reg = <0x07a00000 0x800000>;
> + };
> +
> + partition@8200000 {
> + label = "rootfs-2";
> + reg = <0x08200000 0x7100000>;
> + };
> +
> + partition@f300000 {
> + label = "default_sw";
> + reg = <0x0f300000 0x7900000>;
> + };
> +
> + partition@16c00000 {
> + label = "logs";
> + reg = <0x16c00000 0x1800000>;
> + };
> +
> + partition@18400000 {
> + label = "preset_cfg";
> + reg = <0x18400000 0x100000>;
> + };
> +
> + partition@18500000 {
> + label = "adsl";
> + reg = <0x18500000 0x100000>;
> + };
> +
> + partition@18600000 {
> + label = "storage";
> + reg = <0x18600000 0x7A00000>;
> + };
> +};
> +
> +&rtc {
> + status = "disabled";
> +};
> +
> +&pciec {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + status = "okay";
> +};
> +
> +&sata_phy0 {
> + status = "disabled";
> +};
> +
> +&sata_phy1 {
> + status = "disabled";
> +};
> +
> +&usb0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +
> + port@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> + #trigger-source-cells = <0>;
> +
> + hub_port1: port@1 {
> + reg = <1>;
> + #trigger-source-cells = <0>;
> + };
> +
> + hub_port3: port@3 {
> + reg = <3>;
> + #trigger-source-cells = <0>;
> + };
> + };
> +};
> --
> 2.20.1
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
