> -----Original Message-----
> From: Rob Herring <robh@xxxxxxxxxx>
> Sent: Wednesday, May 13, 2020 6:53 AM
> To: Ooi, Joyce <joyce.ooi@xxxxxxxxx>
> Cc: Thor Thayer <thor.thayer@xxxxxxxxxxxxxxx>; David S . Miller
> <davem@xxxxxxxxxxxxx>; netdev@xxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; Westergreen, Dalon
> <dalon.westergreen@xxxxxxxxx>; Tan, Ley Foon <ley.foon.tan@xxxxxxxxx>;
> See, Chin Liang <chin.liang.see@xxxxxxxxx>; Nguyen, Dinh
> <dinh.nguyen@xxxxxxxxx>; devicetree@xxxxxxxxxxxxxxx
> Subject: Re: [PATCHv2 10/10] net: eth: altera: update devicetree bindings
> documentation
>
> On Mon, May 04, 2020 at 04:25:58PM +0800, Joyce Ooi wrote:
> > From: Dalon Westergreen <dalon.westergreen@xxxxxxxxx>
> >
> > Update devicetree bindings documentation to include msgdma prefetcher
> > and ptp bindings.
> >
> > Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> > Cc: devicetree@xxxxxxxxxxxxxxx
> > Signed-off-by: Dalon Westergreen <dalon.westergreen@xxxxxxxxx>
> > Signed-off-by: Joyce Ooi <joyce.ooi@xxxxxxxxx>
> > ---
> > v2: no change
> > ---
> > .../devicetree/bindings/net/altera_tse.txt | 103
> +++++++++++++++++----
> > 1 file changed, 84 insertions(+), 19 deletions(-)
>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
>
> One nit below.
>
> >
> > diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt
> > b/Documentation/devicetree/bindings/net/altera_tse.txt
> > index 0b7d4d3758ea..2f2d12603907 100644
> > --- a/Documentation/devicetree/bindings/net/altera_tse.txt
> > +++ b/Documentation/devicetree/bindings/net/altera_tse.txt
> > @@ -2,53 +2,86 @@
> >
> > Required properties:
> > - compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and
> should
> > - be "altr,tse-msgdma-1.0" for the preferred MSGDMA based
> TSE.
> > + be "altr,tse-msgdma-1.0" for the preferred MSGDMA based
> TSE,
> > + and "altr,tse-msgdma-2.0" for MSGDMA with prefetcher
> based
> > + implementations.
> > ALTR is supported for legacy device trees, but is deprecated.
> > altr should be used for all new designs.
> > - reg: Address and length of the register set for the device. It contains
> > the information of registers in the same order as described by
> > reg-names
> > - reg-names: Should contain the reg names
> > - "control_port": MAC configuration space region
> > - "tx_csr": xDMA Tx dispatcher control and status space region
> > - "tx_desc": MSGDMA Tx dispatcher descriptor space region
> > - "rx_csr" : xDMA Rx dispatcher control and status space region
> > - "rx_desc": MSGDMA Rx dispatcher descriptor space region
> > - "rx_resp": MSGDMA Rx dispatcher response space region
> > - "s1": SGDMA descriptor memory
> > - interrupts: Should contain the TSE interrupts and it's mode.
> > - interrupt-names: Should contain the interrupt names
> > - "rx_irq": xDMA Rx dispatcher interrupt
> > - "tx_irq": xDMA Tx dispatcher interrupt
> > + "rx_irq": DMA Rx dispatcher interrupt
> > + "tx_irq": DMA Tx dispatcher interrupt
> > - rx-fifo-depth: MAC receive FIFO buffer depth in bytes
> > - tx-fifo-depth: MAC transmit FIFO buffer depth in bytes
> > - phy-mode: See ethernet.txt in the same directory.
> > - phy-handle: See ethernet.txt in the same directory.
> > - phy-addr: See ethernet.txt in the same directory. A configuration should
> > include phy-handle or phy-addr.
> > -- altr,has-supplementary-unicast:
> > - If present, TSE supports additional unicast addresses.
> > - Otherwise additional unicast addresses are not supported.
> > -- altr,has-hash-multicast-filter:
> > - If present, TSE supports a hash based multicast filter.
> > - Otherwise, hash-based multicast filtering is not supported.
> > -
> > - mdio device tree subnode: When the TSE has a phy connected to its local
> > mdio, there must be device tree subnode with the following
> > required properties:
> > -
> > - compatible: Must be "altr,tse-mdio".
> > - #address-cells: Must be <1>.
> > - #size-cells: Must be <0>.
> >
> > For each phy on the mdio bus, there must be a node with the
> following
> > fields:
> > -
> > - reg: phy id used to communicate to phy.
> > - device_type: Must be "ethernet-phy".
> >
> > The MAC address will be determined using the optional properties
> > defined in ethernet.txt.
> >
> > +- altr,has-supplementary-unicast:
> > + If present, TSE supports additional unicast addresses.
> > + Otherwise additional unicast addresses are not supported.
> > +- altr,has-hash-multicast-filter:
> > + If present, TSE supports a hash based multicast filter.
> > + Otherwise, hash-based multicast filtering is not supported.
> > +- altr,has-ptp:
> > + If present, TSE supports 1588 timestamping. Currently only
> > + supported with the msgdma prefetcher.
> > +- altr,tx-poll-cnt:
> > + Optional cycle count for Tx prefetcher to poll descriptor
> > + list. If not present, defaults to 128, which at 125MHz is
> > + roughly 1usec. Only for "altr,tse-msgdma-2.0".
> > +- altr,rx-poll-cnt:
> > + Optional cycle count for Tx prefetcher to poll descriptor
> > + list. If not present, defaults to 128, which at 125MHz is
> > + roughly 1usec. Only for "altr,tse-msgdma-2.0".
> > +
> > +Required registers by compatibility string:
> > + - "altr,tse-1.0"
> > + "control_port": MAC configuration space region
> > + "tx_csr": DMA Tx dispatcher control and status space region
> > + "rx_csr" : DMA Rx dispatcher control and status space region
> > + "s1": DMA descriptor memory
> > +
> > + - "altr,tse-msgdma-1.0"
> > + "control_port": MAC configuration space region
> > + "tx_csr": DMA Tx dispatcher control and status space region
> > + "tx_desc": DMA Tx dispatcher descriptor space region
> > + "rx_csr" : DMA Rx dispatcher control and status space region
> > + "rx_desc": DMA Rx dispatcher descriptor space region
> > + "rx_resp": DMA Rx dispatcher response space region
> > +
> > + - "altr,tse-msgdma-2.0"
> > + "control_port": MAC configuration space region
> > + "tx_csr": DMA Tx dispatcher control and status space region
> > + "tx_pref": DMA Tx prefetcher configuration space region
> > + "rx_csr" : DMA Rx dispatcher control and status space region
> > + "rx_pref": DMA Rx prefetcher configuration space region
> > + "tod_ctrl": Time of Day Control register only required when
> > + timestamping support is enabled. Timestamping is
> > + only supported with the msgdma-2.0
> implementation.
> > +
> > +Optional properties:
> > +- local-mac-address: See ethernet.txt in the same directory.
> > +- max-frame-size: See ethernet.txt in the same directory.
> > +
> > Example:
> >
> > tse_sub_0_eth_tse_0: ethernet@1,00000000 { @@ -86,6 +119,11
> @@
> > Example:
> > device_type = "ethernet-phy";
> > };
> >
> > + phy2: ethernet-phy@2 {
> > + reg = <0x2>;
> > + device_type = "ethernet-phy";
> > + };
> > +
> > };
> > };
> >
> > @@ -111,3 +149,30 @@ Example:
> > altr,has-hash-multicast-filter;
> > phy-handle = <&phy1>;
> > };
> > +
> > +
> > + tse_sub_2_eth_tse_0: ethernet@1,00002000 {
>
> What bus is this on? Usually a ',' like this is for a chip select number. If just a
> 64-bit address, then no comma.
It's a 64-bit address. I'll remove the comma for this and the one above.
>
> > + compatible = "altr,tse-msgdma-2.0";
> > + reg = <0x00000001 0x00002000 0x00000400>,
> > + <0x00000001 0x00002400 0x00000020>,
> > + <0x00000001 0x00002420 0x00000020>,
> > + <0x00000001 0x00002440 0x00000020>,
> > + <0x00000001 0x00002460 0x00000020>,
> > + <0x00000001 0x00002480 0x00000040>;
> > + reg-names = "control_port", "rx_csr", "rx_pref","tx_csr",
> "tx_pref", "tod_ctrl";
> > + interrupt-parent = <&hps_0_arm_gic_0>;
> > + interrupts = <0 45 4>, <0 44 4>;
> > + interrupt-names = "rx_irq", "tx_irq";
> > + rx-fifo-depth = <2048>;
> > + tx-fifo-depth = <2048>;
> > + address-bits = <48>;
> > + max-frame-size = <1500>;
> > + local-mac-address = [ 00 00 00 00 00 00 ];
> > + phy-mode = "sgmii";
> > + altr,has-supplementary-unicast;
> > + altr,has-hash-multicast-filter;
> > + altr,has-ptp;
> > + altr,tx-poll-cnt = <128>;
> > + altr,rx-poll-cnt = <32>;
> > + phy-handle = <&phy2>;
> > + };
> > --
> > 2.13.0
> >
