[PATCH v2 5/6] phy: amlogic: meson8b-usb2: unset the IDDQ bit during PHY power-on

[Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>]

The vendor driver unsets the set_iddig bit during power-on as well and
sets it when suspending the PHY. I did not notice this in the vendor
driver first, because it's part of the dwc_otg driver there (instead of
their PHY code). While here, also add all other REG_DBG_UART register
bit definitions.

Tested-by: Thomas Graichen <thomas.graichen@xxxxxxxxx>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
---
 drivers/phy/amlogic/phy-meson8b-usb2.c | 44 +++++++++++++++++++-------
 1 file changed, 32 insertions(+), 12 deletions(-)

diff --git a/drivers/phy/amlogic/phy-meson8b-usb2.c b/drivers/phy/amlogic/phy-meson8b-usb2.c
index 7236b8885f07..436dfa1a8a04 100644
--- a/drivers/phy/amlogic/phy-meson8b-usb2.c
+++ b/drivers/phy/amlogic/phy-meson8b-usb2.c
@@ -78,6 +78,17 @@
 	#define REG_ADP_BC_ACA_PIN_FLOAT		BIT(26)
 
 #define REG_DBG_UART					0x10
+	#define REG_DBG_UART_BYPASS_SEL			BIT(0)
+	#define REG_DBG_UART_BYPASS_DM_EN		BIT(1)
+	#define REG_DBG_UART_BYPASS_DP_EN		BIT(2)
+	#define REG_DBG_UART_BYPASS_DM_DATA		BIT(3)
+	#define REG_DBG_UART_BYPASS_DP_DATA		BIT(4)
+	#define REG_DBG_UART_FSV_MINUS			BIT(5)
+	#define REG_DBG_UART_FSV_PLUS			BIT(6)
+	#define REG_DBG_UART_FSV_BURN_IN_TEST		BIT(7)
+	#define REG_DBG_UART_LOOPBACK_EN_B		BIT(8)
+	#define REG_DBG_UART_SET_IDDQ			BIT(9)
+	#define REG_DBG_UART_ATE_RESET			BIT(10)
 
 #define REG_TEST					0x14
 	#define REG_TEST_DATA_IN_MASK			GENMASK(3, 0)
@@ -172,20 +183,24 @@ static int phy_meson8b_usb2_power_on(struct phy *phy)
 	regmap_update_bits(priv->regmap, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT,
 			   REG_CTRL_SOF_TOGGLE_OUT);
 
-	if (priv->dr_mode == USB_DR_MODE_HOST &&
-	    priv->match->host_enable_aca) {
-		regmap_update_bits(priv->regmap, REG_ADP_BC,
-				   REG_ADP_BC_ACA_ENABLE,
-				   REG_ADP_BC_ACA_ENABLE);
+	if (priv->dr_mode == USB_DR_MODE_HOST) {
+		regmap_update_bits(priv->regmap, REG_DBG_UART,
+				   REG_DBG_UART_SET_IDDQ, 0);
 
-		udelay(ACA_ENABLE_COMPLETE_TIME);
+		if (priv->match->host_enable_aca) {
+			regmap_update_bits(priv->regmap, REG_ADP_BC,
+					   REG_ADP_BC_ACA_ENABLE,
+					   REG_ADP_BC_ACA_ENABLE);
 
-		regmap_read(priv->regmap, REG_ADP_BC, &reg);
-		if (reg & REG_ADP_BC_ACA_PIN_FLOAT) {
-			dev_warn(&phy->dev, "USB ID detect failed!\n");
-			clk_disable_unprepare(priv->clk_usb);
-			clk_disable_unprepare(priv->clk_usb_general);
-			return -EINVAL;
+			udelay(ACA_ENABLE_COMPLETE_TIME);
+
+			regmap_read(priv->regmap, REG_ADP_BC, &reg);
+			if (reg & REG_ADP_BC_ACA_PIN_FLOAT) {
+				dev_warn(&phy->dev, "USB ID detect failed!\n");
+				clk_disable_unprepare(priv->clk_usb);
+				clk_disable_unprepare(priv->clk_usb_general);
+				return -EINVAL;
+			}
 		}
 	}
 
@@ -196,6 +211,11 @@ static int phy_meson8b_usb2_power_off(struct phy *phy)
 {
 	struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy);
 
+	if (priv->dr_mode == USB_DR_MODE_HOST)
+		regmap_update_bits(priv->regmap, REG_DBG_UART,
+				   REG_DBG_UART_SET_IDDQ,
+				   REG_DBG_UART_SET_IDDQ);
+
 	clk_disable_unprepare(priv->clk_usb);
 	clk_disable_unprepare(priv->clk_usb_general);
 
-- 
2.26.2