Hi,
This series convert the adi,adv7511.txt DT bindings to json-schema. As a
result of the conversion some dts files needed to be updated.
The changes to the dts files are of three types:
- Reordering of the I2C slave addresses list of the ADV75xx node. The
addresses in the 'reg' property and the matching names in
'reg-names' for an I2C slave don't need to be in any particular
order, but the DT schema defines these properties as a cell array
and a string array respectively, which are ordered, so the
definitions in the dts files must match the order in the binding.
- Filling the minimum binding requirements. Most of the time this
means creating a 'ports' node in the boards that don't define
them. Note, however, that the purpose of this is simply to make the
definition compliant with the binding. I didn't define any endpoints
for the ports.
- Removing unneeded properties.
About the binding conversion:
- The original binding covered five different devices: ADV7511,
ADV7511W, ADV7513, ADV7533 and ADV7535. They all share a common set
of properties but ADV7533 and ADV7535 have enough differences from
the rest to warrant their own binding file. In v1 I modelled all the
properties constraints for all five devices in a single file but it
turned out a bit too complex. Splitting the binding into one for
ADV7511/11W/13 and another for ADV7533/35 makes them much easier to
read and maintain.
Patches 1/6 to 5/6 contain the dts changes. Patch 6/6 contains the
binding conversion.
NOTE: the bindings have been tested with:
make dt_binding_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
make dtbs_check ARCH=<arch> DT_SCHEMA_FILES=<...adi,adv7511.yaml>
for <arch> = arm and arm64. dts changes haven't been tested in hardware.
Changes in v2:
- [Rob] adi,adv7511.yaml split into two files: adi,adv7511.yaml and
adi,adv7533.yaml.
- [Rob] Remove maxItems from supplies.
- Additional DTs fixes:
- iwg20d-q7-dbcm-ca.dtsi
- r8a7745-iwg22d-sodimm-dbhd-ca.dts
- r8a7790-lager.dts
- r8a7790-stout.dts
- r8a7791-koelsch.dts
- r8a7791-porter.dts
- r8a7792-blanche.dts
- r8a7793-gose.dts
- r8a7794-silk.dts
- hi6220-hikey.dts
- r8a77970-eagle.dts
- r8a77970-v3msk.dts
- r8a77980-condor.dts
- r8a77980-v3hsk.dts
- r8a77990-ebisu.dts
Kind regards,
Ricardo
Ricardo Cañuelo (6):
arm64: dts: renesas: make hdmi encoder nodes compliant with DT
bindings
ARM: dts: renesas: make hdmi encoder nodes compliant with DT bindings
ARM: dts: zynq: add port definitions to hdmi-tx@39
arm64: dts: hisilicon: hikey: fixes to comply with adi,adv7533 DT
binding
ARM: dts: iwg20d-q7-dbcm-ca: remove unneeded properties in hdmi@39
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
.../bindings/display/bridge/adi,adv7511.txt | 143 -----------
.../bindings/display/bridge/adi,adv7511.yaml | 230 ++++++++++++++++++
.../bindings/display/bridge/adi,adv7533.yaml | 166 +++++++++++++
arch/arm/boot/dts/iwg20d-q7-dbcm-ca.dtsi | 2 -
.../dts/r8a7745-iwg22d-sodimm-dbhd-ca.dts | 2 -
arch/arm/boot/dts/r8a7790-lager.dts | 2 -
arch/arm/boot/dts/r8a7790-stout.dts | 2 -
arch/arm/boot/dts/r8a7791-koelsch.dts | 2 -
arch/arm/boot/dts/r8a7791-porter.dts | 2 -
arch/arm/boot/dts/r8a7792-blanche.dts | 2 -
arch/arm/boot/dts/r8a7792-wheat.dts | 12 +-
arch/arm/boot/dts/r8a7793-gose.dts | 2 -
arch/arm/boot/dts/r8a7794-silk.dts | 2 -
arch/arm/boot/dts/zynq-zc702.dts | 10 +
arch/arm/boot/dts/zynq-zc706.dts | 10 +
.../boot/dts/hisilicon/hi3660-hikey960.dts | 11 +
.../arm64/boot/dts/hisilicon/hi6220-hikey.dts | 2 +-
.../arm64/boot/dts/renesas/r8a77970-eagle.dts | 2 -
.../arm64/boot/dts/renesas/r8a77970-v3msk.dts | 2 -
.../boot/dts/renesas/r8a77980-condor.dts | 2 -
.../arm64/boot/dts/renesas/r8a77980-v3hsk.dts | 2 -
.../arm64/boot/dts/renesas/r8a77990-ebisu.dts | 2 -
.../arm64/boot/dts/renesas/r8a77995-draak.dts | 6 +-
23 files changed, 434 insertions(+), 184 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7511.yaml
create mode 100644 Documentation/devicetree/bindings/display/bridge/adi,adv7533.yaml
--
2.18.0
