Hi Sakari, Tomasz, On Thu, 2020-05-07 at 16:25 +0200, Tomasz Figa wrote: > On Thu, May 7, 2020 at 4:12 PM Sakari Ailus > <sakari.ailus@xxxxxxxxxxxxxxx> wrote: > > > > Hi Tomasz, Dongchun, > > > > On Thu, May 07, 2020 at 03:50:40PM +0200, Tomasz Figa wrote: > > > Hi Sakari and Dongchun, > > > > > > On Thu, May 7, 2020 at 3:00 PM Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> wrote: > > > > > > > > Hi Sakari, > > > > > > > > Thanks for the review. > > > > > > > > On Wed, 2020-05-06 at 14:21 +0300, Sakari Ailus wrote: > > > > > Hi Dongchun, > > > > > > > > > > On Tue, May 05, 2020 at 10:17:18PM +0800, Dongchun Zhu wrote: > > > > > > Hi Sakari, > > > > > > > > > > > > Thanks for the review. > > > > > > > > > > > > On Tue, 2020-05-05 at 10:04 +0300, Sakari Ailus wrote: > > > > > > > Hi Dongchun, > > > > > > > > > > > > > > On Thu, Apr 30, 2020 at 04:09:23PM +0800, Dongchun Zhu wrote: > > > > > > > > Add DT bindings documentation for Omnivision OV02A10 image sensor. > > > > > > > > > > > > > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > > > > > > > --- > > > > > > > > .../bindings/media/i2c/ovti,ov02a10.yaml | 148 +++++++++++++++++++++ > > > > > > > > MAINTAINERS | 7 + > > > > > > > > 2 files changed, 155 insertions(+) > > > > > > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > > > > > > > > > > > > > diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > > > > > new file mode 100644 > > > > > > > > index 0000000..2be4bd2 > > > > > > > > --- /dev/null > > > > > > > > +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov02a10.yaml > > > > > > > > @@ -0,0 +1,148 @@ > > > > > > > > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) > > > > > > > > +# Copyright (c) 2020 MediaTek Inc. > > > > > > > > +%YAML 1.2 > > > > > > > > +--- > > > > > > > > +$id: http://devicetree.org/schemas/media/i2c/ovti,ov02a10.yaml# > > > > > > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > > > > > > + > > > > > > > > +title: Omnivision OV02A10 CMOS Sensor Device Tree Bindings > > > > > > > > + > > > > > > > > +maintainers: > > > > > > > > + - Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx> > > > > > > > > + > > > > > > > > +description: |- > > > > > > > > + The Omnivision OV02A10 is a low-cost, high performance, 1/5-inch, 2 megapixel > > > > > > > > + image sensor, which is the latest production derived from Omnivision's CMOS > > > > > > > > + image sensor technology. Ihis chip supports high frame rate speeds up to 30fps > > > > > > > > + @ 1600x1200 (UXGA) resolution transferred over a 1-lane MIPI interface. The > > > > > > > > + sensor output is available via CSI-2 serial data output. > > > > > > > > + > > > > > > > > +properties: > > > > > > > > + compatible: > > > > > > > > + const: ovti,ov02a10 > > > > > > > > + > > > > > > > > + reg: > > > > > > > > + maxItems: 1 > > > > > > > > + > > > > > > > > + clocks: > > > > > > > > + items: > > > > > > > > + - description: top mux camtg clock > > > > > > > > + - description: devider clock > > > > > > > > + > > > > > > > > + clock-names: > > > > > > > > + items: > > > > > > > > + - const: eclk > > > > > > > > + - const: freq_mux > > > > > > > > + > > > > > > > > + clock-frequency: > > > > > > > > + description: > > > > > > > > + Frequency of the eclk clock in Hertz. > > > > > > > > + > > > > > > > > + dovdd-supply: > > > > > > > > + description: > > > > > > > > + Definition of the regulator used as interface power supply. > > > > > > > > + > > > > > > > > + avdd-supply: > > > > > > > > + description: > > > > > > > > + Definition of the regulator used as analog power supply. > > > > > > > > + > > > > > > > > + dvdd-supply: > > > > > > > > + description: > > > > > > > > + Definition of the regulator used as digital power supply. > > > > > > > > + > > > > > > > > + powerdown-gpios: > > > > > > > > + description: > > > > > > > > + The phandle and specifier for the GPIO that controls sensor powerdown. > > > > > > > > + > > > > > > > > + reset-gpios: > > > > > > > > + description: > > > > > > > > + The phandle and specifier for the GPIO that controls sensor reset. > > > > > > > > + > > > > > > > > + rotation: > > > > > > > > + description: > > > > > > > > + Definition of the sensor's placement, valid values are 0 and 180. > > > > > > > > + allOf: > > > > > > > > + - $ref: "/schemas/types.yaml#/definitions/uint32" > > > > > > > > + - enum: > > > > > > > > + - 0 # Sensor Mounted Upright > > > > > > > > + - 180 # Sensor Mounted Upside Down > > > > > > > > + > > > > > > > > + ovti,mipi-tx-speed: > > > > > > > > + description: > > > > > > > > + Indication of MIPI transmission speed select. > > > > > > > > > > > > > > What exactly does this signify? And how do you come up with the number? > > > > > > > > > > > > > > > > > > > Apologies for not addressing this number clear. > > > > > > > > > > > > From the datasheet, P1:0xA1 register represents TX_SPEED_AREA_SEL with > > > > > > the default val: 0x03. > > > > > > The description of this RW register is as below: > > > > > > Bit[2:0]: MIPI transmission speed select. > > > > > > > > > > > > Thus the enum should be definited as [ 0, 1, 2, 3, 4, 5, 6, 7 ]. > > > > > > This would be fixed in next release. > > > > > > > > > > > > In the meantime, as the default val of P1:0xA1 is 0x03, we hope to keep > > > > > > that value if there is no setting for this private property in DT. > > > > > > The caller in driver would be updated like this in next release. > > > > > > if (ov02a10->mipi_clock_tx_speed) > > > > > > ret = i2c_smbus_write_byte_data(...,...); > > > > > > > > > > How did you pick the value in the example? And why do you believe it is > > > > > specific to a platform, and not e.g. a sensor mode? > > > > > > > > > > > > > We look into P1:0XA1, one register that defines MIPI transmission speed > > > > select. > > > > From the datasheet, we can get the possible values that could be set to > > > > P1:0xA1. > > > > > > > > Actually this register is an independent of sensor mode, it is just > > > > included in sensor mode's register setting table. > > > > > > > > In addition, this private DT Property is created to fix the MIPI test > > > > failure. The register values are adjusted and verified from vendor to > > > > make sensor signal meet MIPI specification. > > > > > > > > > > In theory the value could depend on the mode, because different link > > > rate could impose different requirements for the physical interface. > > > In practice, we haven't seen any hardware that would require different > > > values for different modes. > > > > The mode (possibly in conjunction with other information available to the > > driver via V4L2 fwnode interface) precisely defines the parameters of the > > CSI-2 bus --- apart from the possible exception of the bus timing related > > parameters but this is not supported by the name of the parameter. > > > > Therefore I don't see how this parameter, which supposedly is used to > > determine the CSI-2 transmissions speed, could be board specific and thus > > belong to DT. > > According to the very imprecise information I have access to, it is > not about the CSI-2 bus itself, but rather some internal parameter of > the sensor's CSI interface. Unfortunately there isn't much information > on what this value exactly controls... > > Best regards, > Tomasz Just got some feedback from OV vendor about this parameter. P1:0xA1 is the register to control D-PHY timing setting based on bclk. It is to adjust the MIPI clock voltage to improve the clock drive capability, and has no affect on the transmission speed of MIPI data. >From vendor's perspective, P1:0xA1 depends upon the length of FPC of camera module that used on the board. Considering the physical connections for MIPI signals to user-facing camera are very different between our 2 projects, it can be very difficult to find universal SI parameters for both projects. Thus here we create one new DT property to separate these tuning in driver, to be more like project-specific. More details about the register is as below. P1:0xA1 val: 0x03 default Case: 0 20MHz-30MHz 1 30MHz-50MHz 2 50MHz-75MHz 3 75MHz-100MHz (default, old DB setting use) 4 100MHz-130MHz (suggested, new DB setting use) 5 Manual So the value in the example should be [ 0, 1, 2, 3, 4, 5 ]. Additionally, P1:0xA1 is recommended to be set as 0x04 in the newest DB setting. We would adjust the register in next release.
