Hi rob,
On 4/28/20 5:28 PM, Rob Herring wrote:
On Wed, Apr 15, 2020 at 05:57:25PM +0200, Christophe Kerello wrote:
This patch adds the documentation of the device tree bindings for the STM32
FMC2 controller.
Signed-off-by: Christophe Kerello <christophe.kerello@xxxxxx>
---
.../devicetree/bindings/mfd/st,stm32-fmc2.yaml | 370 +++++++++++++++++++++
1 file changed, 370 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/st,stm32-fmc2.yaml
diff --git a/Documentation/devicetree/bindings/mfd/st,stm32-fmc2.yaml b/Documentation/devicetree/bindings/mfd/st,stm32-fmc2.yaml
new file mode 100644
index 0000000..0ce1340
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/st,stm32-fmc2.yaml
@@ -0,0 +1,370 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/st,stm32-fmc2.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings
+
+description: |
+ The FMC2 functional block makes the interface with: synchronous and
+ asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped
+ peripherals) and NAND flash memories.
+ Its main purposes are:
+ - to translate AXI transactions into the appropriate external device
+ protocol
+ - to meet the access time requirements of the external devices
+ All external devices share the addresses, data and control signals with the
+ controller. Each external device is accessed by means of a unique Chip
+ Select. The FMC2 performs only one access at a time to an external device.
+
+maintainers:
+ - Christophe Kerello <christophe.kerello@xxxxxx>
+
+properties:
+ compatible:
+ const: st,stm32mp1-fmc2
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 1
+
+ ranges: true
+
+patternProperties:
+ "^ebi(@.*)?":
+ type: object
+
+ properties:
+ compatible:
+ const: st,stm32mp1-fmc2-ebi
+
+ "#address-cells":
+ const: 2
+
+ "#size-cells":
+ const: 1
+
+ ranges: true
+
+ patternProperties:
+ "^[a-zA-Z]*-ebi@[a-f0-9,]*$":
These nodes should be named based on the device connected and we can be
a bit more precise on the unit-address:
"@[0-9a-f],[0-9a-f]+$"
Adjust for how many chip selects there are. 15 seems unlikely.
Ok. It will be modified in v3.
+ type: object
+
+ properties:
+ reg:
+ maxItems: 1
+
+ st,fmc2_ebi_cs_transaction_type:
s/_/-/
And for the rest of the vendor properties...
Ok. It will be modified in v3.
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - minimum: 0
+ maximum: 11
+ description: |
+ Select one of the transactions type supported
+ 0: Asynchronous mode 1 SRAM/FRAM
+ 1: Asynchronous mode 1 PSRAM.
+ 2: Asynchronous mode A SRAM/FRAM.
+ 3: Asynchronous mode A PSRAM.
+ 4: Asynchronous mode 2 NOR.
+ 5: Asynchronous mode B NOR.
+ 6: Asynchronous mode C NOR.
+ 7: Asynchronous mode D NOR.
+ 8: Synchronous read synchronous write PSRAM.
+ 9: Synchronous read asynchronous write PSRAM.
+ 10: Synchronous read synchronous write NOR.
+ 11: Synchronous read asynchronous write NOR.
+
+ st,fmc2_ebi_cs_cclk_enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Continuous clock enable (first bank must be configured
+ in synchronous mode). The FMC_CLK is generated continuously
+ during asynchronous and synchronous access. By default, the
+ FMC_CLK is only generated during synchronous access.
+
+ st,fmc2_ebi_cs_mux_enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Address/Data multiplexed on databus (valid only with
+ NOR and PSRAM transactions type). By default, Address/Data are
+ not multiplexed.
+
+ st,fmc2_ebi_cs_buswidth:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [ 8, 16 ]
+ - default: 16
+ description: Data bus width
+
+ st,fmc2_ebi_cs_waitpol_high:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: Wait signal polarity (NWAIT signal active high).
+ By default, NWAIT is active low.
+
+ st,fmc2_ebi_cs_waitcfg_enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: The NWAIT signal indicates wheither the data from the
+ device are valid or if a wait state must be inserted when
+ accessing the device in synchronous mode. By default, the NWAIT
+ signal is active one data cycle before wait state.
+
+ st,fmc2_ebi_cs_wait_enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: The NWAIT signal is enabled (its level is taken into
+ account after the programmed latency period to insert wait states
+ if asserted). By default, the NWAIT signal is disabled.
+
+ st,fmc2_ebi_cs_asyncwait_enable:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description: The NWAIT signal is taken into account during
+ asynchronous transactions. By default, the NWAIT signal is not
+ taken into account during asynchronous transactions.
+
+ st,fmc2_ebi_cs_cpsize:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - enum: [ 0, 128, 256, 512, 1024 ]
+ - default: 0
+ description: CRAM page size. The controller splits the burst access
+ when the memory page is reached. By default, no burst split when
+ crossing page boundary.
+
+ st,fmc2_ebi_cs_byte_lane_setup:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property configures the byte lane setup timing
+ defined in ns from NBLx low to Chip Select NEx low.
If units are nsec, then use the standard unit suffixes. Then you don't
need to define the type either.
Ok. It will be modified in v3.
+
+ st,fmc2_ebi_cs_address_setup:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the address
+ setup phase in ns used for asynchronous read/write transactions.
+
+ st,fmc2_ebi_cs_address_hold:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the address
+ hold phase in ns used for asynchronous multiplexed
+ read/write transactions.
+
+ st,fmc2_ebi_cs_data_setup:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the data
+ setup phase in ns used for asynchronous read/write transactions.
+
+ st,fmc2_ebi_cs_bus_turnaround:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the delay between the end of
+ current read/write transaction and the next transaction.
+
+ st,fmc2_ebi_cs_data_hold:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the data
+ hold phase in ns used for asynchronous read/write transactions.
+
+ st,fmc2_ebi_cs_clk_period:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the FMC_CLK output signal period in ns.
+
+ st,fmc2_ebi_cs_data_latency:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the data latency before reading or writing
+ the first data. This timing is expressed in FMC_CLK periods.
+
+ st,fmc2_ebi_cs_write_address_setup:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the address
+ setup phase in ns used for asynchronous write transactions.
+
+ st,fmc2_ebi_cs_write_address_hold:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the address hold phase in
+ ns used for asynchronous multiplexed write transactions.
+
+ st,fmc2_ebi_cs_write_data_setup:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the data setup phase in
+ ns used for asynchronous write transactions.
+
+ st,fmc2_ebi_cs_write_bus_turnaround:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the delay between the end of current
+ write transaction and the next transaction.
+
+ st,fmc2_ebi_cs_write_data_hold:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the duration of the data hold phase
+ in ns used for asynchronous write transactions.
+
+ st,fmc2_ebi_cs_max_low_pulse:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ description: This property defines the maximum chip select low pulse duration
+ in ns for synchronous transactions. When this timing reaches 0,
+ the controller splits the current access, toggles NE to allow
+ device refresh and restarts a new access.
+
+ required:
+ - reg
+ - st,fmc2_ebi_cs_transaction_type
+
+ additionalProperties: false
+
+ required:
+ - compatible
+ - "#address-cells"
+ - "#size-cells"
+ - ranges
+
+ nand-controller:
+ allOf:
+ - $ref: "../mtd/nand-controller.yaml#"
+
+ type: object
+
+ properties:
+ compatible:
+ const: st,stm32mp1-fmc2-nand
+
+ reg:
+ items:
+ - description: Chip select 0 data
+ - description: Chip select 0 command
+ - description: Chip select 0 address space
+ - description: Chip select 1 data
+ - description: Chip select 1 command
+ - description: Chip select 1 address space
+
+ interrupts:
+ maxItems: 1
+
+ dmas:
+ items:
+ - description: tx DMA channel
+ - description: rx DMA channel
+ - description: ecc DMA channel
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+ - const: ecc
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ patternProperties:
+ "^nand@[a-f0-9]$":
+ type: object
+
+ properties:
+ nand-ecc-step-size:
+ const: 512
+
+ nand-ecc-strength:
+ enum: [1, 4 ,8 ]
+
+ additionalProperties: false
+
+ required:
+ - "#address-cells"
+ - "#size-cells"
+ - compatible
+ - reg
+ - interrupts
+
+ additionalProperties: false
Wrong indentation. You are defining a DT property called
'additionalProperties'. You need 2 of these at 0 and 4 spaces
indentation. I have a check for this error in dt-schema pending.
Ok. It will be modified in v3.
Regards,
Christophe Kerello.
+
+required:
+ - "#address-cells"
+ - "#size-cells"
+ - compatible
+ - reg
+ - clocks
+ - ranges
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/clock/stm32mp1-clks.h>
+ #include <dt-bindings/reset/stm32mp1-resets.h>
+ fmc@58002000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp1-fmc2";
+ reg = <0x58002000 0x1000>;
+ clocks = <&rcc FMC_K>;
+ resets = <&rcc FMC_R>;
+ ranges;
+
+ ebi@0 {
+ #address-cells = <2>;
+ #size-cells = <1>;
+ compatible = "st,stm32mp1-fmc2-ebi";
+ ranges = <0 0 0x60000000 0x4000000>,
+ <1 0 0x64000000 0x4000000>,
+ <2 0 0x68000000 0x4000000>,
+ <3 0 0x6c000000 0x4000000>;
+
+ psram-ebi@0,0 {
+ compatible = "mtd-ram";
+ reg = <0 0x00000000 0x100000>;
+ bank-width = <2>;
+
+ st,fmc2_ebi_cs_transaction_type = <1>;
+ st,fmc2_ebi_cs_address_setup = <60>;
+ st,fmc2_ebi_cs_data_setup = <30>;
+ st,fmc2_ebi_cs_bus_turnaround = <5>;
+ };
+ };
+
+ nand-controller@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "st,stm32mp1-fmc2-nand";
+ reg = <0x80000000 0x1000>,
+ <0x88010000 0x1000>,
+ <0x88020000 0x1000>,
+ <0x81000000 0x1000>,
+ <0x89010000 0x1000>,
+ <0x89020000 0x1000>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+ <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+ <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+ dma-names = "tx", "rx", "ecc";
+
+ nand@0 {
+ reg = <0>;
+ nand-on-flash-bbt;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+ };
+
+...
--
1.9.1
