Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.
This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.
Signed-off-by: Marek Behún <marek.behun@xxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
---
arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 1 -
arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts | 1 -
arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 1 +
3 files changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
index c92ad664cb0e..b97218c72727 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi
@@ -44,7 +44,6 @@ vcc_sd_reg1: regulator {
/* J9 */
&pcie0 {
status = "okay";
- phys = <&comphy1 0>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index e496bd9d4737..15c1cf5c5b69 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -134,7 +134,6 @@ &pcie0 {
status = "okay";
max-link-speed = <2>;
reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
- phys = <&comphy1 0>;
/* enabled by U-Boot if PCIe module is present */
status = "disabled";
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index 7909c146eabf..5aaad64a793d 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -493,6 +493,7 @@ pcie0: pcie@d0070000 {
<0 0 0 2 &pcie_intc 1>,
<0 0 0 3 &pcie_intc 2>,
<0 0 0 4 &pcie_intc 3>;
+ phys = <&comphy1 0>;
pcie_intc: interrupt-controller {
interrupt-controller;
#interrupt-cells = <1>;
--
2.24.1
