On Fri, Apr 17, 2020 at 11:21 PM Artur Rojek <contact@xxxxxxxxxxxxxx> wrote:
>
> The SADC component in JZ47xx SoCs provides support for touchscreen
> operations (pen position and pen down pressure) in single-ended and
> differential modes.
>
> Of the known hardware to use this controller, GCW Zero and Anbernic RG-350
> utilize the touchscreen mode by having their joystick(s) attached to the
> X/Y positive/negative input pins.
> GCW Zero comes with a single joystick and is sufficiently handled with the
> currently implemented single-ended mode. Support for boards with two
> joysticks, where one is hooked up to Xn/Yn and the other to Xp/Yp channels
> will need to be provided in the future.
>
> The touchscreen component of SADC takes a significant time to stabilize
> after first receiving the clock and a delay of 50ms has been empirically
> proven to be a safe value before data sampling can begin.
>
> All the boards which probe this driver have the interrupt provided from
> devicetree, with no need to handle a case where the irq was not provided.
Device Tree
IRQ
...
> + .scan_type = {
> + .sign = 'u',
> + .realbits = 12,
> + .storagebits = 16
It's slightly better to leave comma in such cases.
> + },
> + .scan_type = {
> + .sign = 'u',
> + .realbits = 12,
> + .storagebits = 16
Ditto.
> + },
...
> .indexed = 1,
> .channel = INGENIC_ADC_AUX,
> + .scan_index = -1
Ditto. You see above? Isn't it nice that you didn't touch that line?
So, perhaps next developer can leverage this subtle kind of things.
> .indexed = 1,
> .channel = INGENIC_ADC_BATTERY,
> + .scan_index = -1
Ditto.
> .indexed = 1,
> .channel = INGENIC_ADC_AUX2,
> + .scan_index = -1
Ditto.
...
> +static int ingenic_adc_buffer_enable(struct iio_dev *iio_dev)
> +{
> + struct ingenic_adc *adc = iio_priv(iio_dev);
> +
> + clk_enable(adc->clk);
Error check?
> + /* It takes significant time for the touchscreen hw to stabilize. */
> + msleep(50);
> + ingenic_adc_set_config(adc, JZ_ADC_REG_CFG_TOUCH_OPS_MASK,
> + JZ_ADC_REG_CFG_SAMPLE_NUM(4) |
> + JZ_ADC_REG_CFG_PULL_UP(4));
> + writew(80, adc->base + JZ_ADC_REG_ADWAIT);
> + writew(2, adc->base + JZ_ADC_REG_ADSAME);
> + writeb((u8)~JZ_ADC_IRQ_TOUCH, adc->base + JZ_ADC_REG_CTRL);
Why casting?
> + writel(0, adc->base + JZ_ADC_REG_ADTCH);
> + ingenic_adc_enable(adc, 2, true);
> +
> + return 0;
> +}
> + irq = platform_get_irq(pdev, 0);
Before it worked w/o IRQ, here is a regression you introduced.
> + if (irq < 0) {
> + dev_err(dev, "Failed to get irq: %d\n", irq);
Redundant message.
> + return irq;
> + }
--
With Best Regards,
Andy Shevchenko
