Hi Sakari,
Thanks for the review and apologies for the delayed response.
> -----Original Message-----
> From: Sakari Ailus <sakari.ailus@xxxxxx>
> Sent: Thursday, August 15, 2019 9:40 PM
> To: Vishal Sagar <vsagar@xxxxxxxxxx>
> Cc: Hyun Kwon <hyunk@xxxxxxxxxx>; laurent.pinchart@xxxxxxxxxxxxxxxx;
> mchehab@xxxxxxxxxx; robh+dt@xxxxxxxxxx; mark.rutland@xxxxxxx; Michal
> Simek <michals@xxxxxxxxxx>; linux-media@xxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; hans.verkuil@xxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; Dinesh Kumar
> <dineshk@xxxxxxxxxx>; Sandip Kothari <sandipk@xxxxxxxxxx>; Luca Ceresoli
> <luca@xxxxxxxxxxxxxxxx>; Jacopo Mondi <jacopo@xxxxxxxxxx>; Hyun Kwon
> <hyunk@xxxxxxxxxx>
> Subject: Re: [PATCH v10 2/2] media: v4l: xilinx: Add Xilinx MIPI CSI-2 Rx
> Subsystem driver
>
> Hi Vishal,
>
> Thanks for the update.
>
> On Thu, Jul 11, 2019 at 02:46:12PM +0530, Vishal Sagar wrote:
> > The Xilinx MIPI CSI-2 Rx Subsystem soft IP is used to capture images
> > from MIPI CSI-2 camera sensors and output AXI4-Stream video data ready
> > for image processing. Please refer to PG232 for details.
> >
> > The CSI2 Rx controller filters out all packets except for the packets
> > with data type fixed in hardware. RAW8 packets are always allowed to
> > pass through.
> >
> > It is also used to setup and handle interrupts and enable the core. It
> > logs all the events in respective counters between streaming on and off.
> >
> > The driver supports only the video format bridge enabled configuration.
> > Some data types like YUV 422 10bpc, RAW16, RAW20 are supported when
> > the CSI v2.0 feature is enabled in design. When the VCX feature is
> > enabled, the maximum number of virtual channels becomes 16 from 4.
> >
> > Signed-off-by: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > Reviewed-by: Hyun Kwon <hyun.kwon@xxxxxxxxxx>
> > ---
> > v10
> > - Removed all V4L2 controls and events based on Sakari's comments.
> > - Now stop_stream() before toggling rst_gpio
> > - Updated init_mbus() to throw error on array out of bound access
> > - Make events and vcx_events as counters instead of structures
> > - Minor fixes in set_format() enum_mbus_code() as suggested by Sakari
> >
> > v9
> > - Moved all controls and events to xilinx-csi2rxss.h
> > - Updated name and description of controls and events
> > - Get control base address from v4l2-controls.h (0x10c0)
> > - Fix KConfig for dependency on VIDEO_XILINX
> > - Added enum_mbus_code() support
> > - Added default format to be returned on open()
> > - Mark variables are const
> > - Remove references to short packet in comments
> > - Add check for streaming before setting active lanes control
> > - strlcpy -> strscpy
> > - Fix xcsi2rxss_set_format()
> >
> > v8
> > - Use clk_bulk* APIs
> > - Add gpio reset for asserting video_aresetn when stream line buffer
> > occurs
> > - Removed short packet related events and irq handling
> > - V4L2_EVENT_XLNXCSIRX_SPKT and V4L2_EVENT_XLNXCSIRX_SPKT_OVF
> > removed
> > - Removed frame counter control
> V4L2_CID_XILINX_MIPICSISS_FRAME_COUNTER
> > and xcsi2rxss_g_volatile_ctrl()
> > - Minor formatting fixes
> >
> > v7
> > - No change
> >
> > v6
> > - No change
> >
> > v5
> > - Removed bayer and updated related parts like set default format based
> > on Luca Cersoli's comments.
> > - Added correct YUV422 10bpc media bus format
> >
> > v4
> > - Removed irq member from core structure
> > - Consolidated IP config prints in xcsi2rxss_log_ipconfig()
> > - Return -EINVAL in case of invalid ioctl
> > - Code formatting
> > - Added reviewed by Hyun Kwon
> >
> > v3
> > - Fixed comments given by Hyun.
> > - Removed DPHY 200 MHz clock. This will be controlled by DPHY driver
> > - Minor code formatting
> > - en_csi_v20 and vfb members removed from struct and made local to dt
> > parsing
> > - lock description updated
> > - changed to ratelimited type for all dev prints in irq handler
> > - Removed YUV 422 10bpc media format
> >
> > v2
> > - Fixed comments given by Hyun and Sakari.
> > - Made all bitmask using BIT() and GENMASK()
> > - Removed unused definitions
> > - Removed DPHY access. This will be done by separate DPHY PHY driver.
> > - Added support for CSI v2.0 for YUV 422 10bpc, RAW16, RAW20 and extra
> > virtual channels
> > - Fixed the ports as sink and source
> > - Now use the v4l2fwnode API to get number of data-lanes
> > - Added clock framework support
> > - Removed the close() function
> > - updated the set format function
> > - support only VFB enabled configuration
> > drivers/media/platform/xilinx/Kconfig | 11 +
> > drivers/media/platform/xilinx/Makefile | 1 +
> > .../media/platform/xilinx/xilinx-csi2rxss.c | 1230 +++++++++++++++++
> > 3 files changed, 1242 insertions(+)
> > create mode 100644 drivers/media/platform/xilinx/xilinx-csi2rxss.c
> >
> > diff --git a/drivers/media/platform/xilinx/Kconfig
> > b/drivers/media/platform/xilinx/Kconfig
> > index a2773ad7c185..349da877c846 100644
> > --- a/drivers/media/platform/xilinx/Kconfig
> > +++ b/drivers/media/platform/xilinx/Kconfig
> > @@ -10,6 +10,17 @@ config VIDEO_XILINX
> >
> > if VIDEO_XILINX
> >
> > +config VIDEO_XILINX_CSI2RXSS
> > + tristate "Xilinx CSI2 Rx Subsystem"
> > + depends on VIDEO_XILINX
>
> You don't need to depend on VIDEO_XILINX here due to the condition above.
>
[Vishal Sagar]
Ok. I will remove the depends line in next version.
> > + help
> > + Driver for Xilinx MIPI CSI2 Rx Subsystem. This is a V4L sub-device
> > + based driver that takes input from CSI2 Tx source and converts
> > + it into an AXI4-Stream. The subsystem comprises of a CSI2 Rx
> > + controller, DPHY, an optional I2C controller and a Video Format
> > + Bridge. The driver is used to set the number of active lanes and
> > + get short packet data.
> > +
> > config VIDEO_XILINX_TPG
> > tristate "Xilinx Video Test Pattern Generator"
> > depends on VIDEO_XILINX
> > diff --git a/drivers/media/platform/xilinx/Makefile
> > b/drivers/media/platform/xilinx/Makefile
> > index 4cdc0b1ec7a5..6119a34f3043 100644
> > --- a/drivers/media/platform/xilinx/Makefile
> > +++ b/drivers/media/platform/xilinx/Makefile
> > @@ -3,5 +3,6 @@
> > xilinx-video-objs += xilinx-dma.o xilinx-vip.o xilinx-vipp.o
> >
> > obj-$(CONFIG_VIDEO_XILINX) += xilinx-video.o
> > +obj-$(CONFIG_VIDEO_XILINX_CSI2RXSS) += xilinx-csi2rxss.o
> > obj-$(CONFIG_VIDEO_XILINX_TPG) += xilinx-tpg.o
> > obj-$(CONFIG_VIDEO_XILINX_VTC) += xilinx-vtc.o diff --git
> > a/drivers/media/platform/xilinx/xilinx-csi2rxss.c
> > b/drivers/media/platform/xilinx/xilinx-csi2rxss.c
> > new file mode 100644
> > index 000000000000..1a22ca80382e
> > --- /dev/null
> > +++ b/drivers/media/platform/xilinx/xilinx-csi2rxss.c
> > @@ -0,0 +1,1230 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Driver for Xilinx MIPI CSI2 Rx Subsystem
> > + *
> > + * Copyright (C) 2016 - 2019 Xilinx, Inc.
> > + *
> > + * Contacts: Vishal Sagar <vishal.sagar@xxxxxxxxxx>
> > + *
> > + */
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/module.h>
> > +#include <linux/mutex.h>
> > +#include <linux/of.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/v4l2-subdev.h>
> > +#include <media/media-entity.h>
> > +#include <media/v4l2-common.h>
> > +#include <media/v4l2-ctrls.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-subdev.h>
> > +#include "xilinx-vip.h"
> > +
> > +/* Register register map */
> > +#define XCSI_CCR_OFFSET 0x00
> > +#define XCSI_CCR_SOFTRESET BIT(1)
> > +#define XCSI_CCR_ENABLE BIT(0)
> > +
> > +#define XCSI_PCR_OFFSET 0x04
> > +#define XCSI_PCR_MAXLANES_MASK GENMASK(4, 3)
> > +#define XCSI_PCR_ACTLANES_MASK GENMASK(1, 0)
> > +
> > +#define XCSI_CSR_OFFSET 0x10
> > +#define XCSI_CSR_PKTCNT GENMASK(31, 16)
> > +#define XCSI_CSR_SPFIFOFULL BIT(3)
> > +#define XCSI_CSR_SPFIFONE BIT(2)
> > +#define XCSI_CSR_SLBF BIT(1)
> > +#define XCSI_CSR_RIPCD BIT(0)
> > +
> > +#define XCSI_GIER_OFFSET 0x20
> > +#define XCSI_GIER_GIE BIT(0)
> > +
> > +#define XCSI_ISR_OFFSET 0x24
> > +#define XCSI_IER_OFFSET 0x28
> > +
> > +#define XCSI_ISR_FR BIT(31)
> > +#define XCSI_ISR_VCXFE BIT(30)
> > +#define XCSI_ISR_WCC BIT(22)
> > +#define XCSI_ISR_ILC BIT(21)
> > +#define XCSI_ISR_SPFIFOF BIT(20)
> > +#define XCSI_ISR_SPFIFONE BIT(19)
> > +#define XCSI_ISR_SLBF BIT(18)
> > +#define XCSI_ISR_STOP BIT(17)
> > +#define XCSI_ISR_SOTERR BIT(13)
> > +#define XCSI_ISR_SOTSYNCERR BIT(12)
> > +#define XCSI_ISR_ECC2BERR BIT(11)
> > +#define XCSI_ISR_ECC1BERR BIT(10)
> > +#define XCSI_ISR_CRCERR BIT(9)
> > +#define XCSI_ISR_DATAIDERR BIT(8)
> > +#define XCSI_ISR_VC3FSYNCERR BIT(7)
> > +#define XCSI_ISR_VC3FLVLERR BIT(6)
> > +#define XCSI_ISR_VC2FSYNCERR BIT(5)
> > +#define XCSI_ISR_VC2FLVLERR BIT(4)
> > +#define XCSI_ISR_VC1FSYNCERR BIT(3)
> > +#define XCSI_ISR_VC1FLVLERR BIT(2)
> > +#define XCSI_ISR_VC0FSYNCERR BIT(1)
> > +#define XCSI_ISR_VC0FLVLERR BIT(0)
> > +
> > +#define XCSI_INTR_PROT_MASK (XCSI_ISR_VC3FSYNCERR |
> XCSI_ISR_VC3FLVLERR |\
> > + XCSI_ISR_VC2FSYNCERR |
> XCSI_ISR_VC2FLVLERR |\
> > + XCSI_ISR_VC1FSYNCERR |
> XCSI_ISR_VC1FLVLERR |\
> > + XCSI_ISR_VC0FSYNCERR |
> XCSI_ISR_VC0FLVLERR |\
> > + XCSI_ISR_VCXFE)
> > +
> > +#define XCSI_INTR_PKTLVL_MASK (XCSI_ISR_ECC2BERR |
> XCSI_ISR_ECC1BERR |\
> > + XCSI_ISR_CRCERR | XCSI_ISR_DATAIDERR)
> > +
> > +#define XCSI_INTR_DPHY_MASK (XCSI_ISR_SOTERR |
> XCSI_ISR_SOTSYNCERR)
> > +
> > +#define XCSI_INTR_SPKT_MASK (XCSI_ISR_SPFIFOF |
> XCSI_ISR_SPFIFONE)
> > +
> > +#define XCSI_INTR_ERR_MASK (XCSI_ISR_WCC | XCSI_ISR_ILC |
> XCSI_ISR_SLBF |\
> > + XCSI_ISR_STOP)
> > +
> > +#define XCSI_INTR_FRAMERCVD_MASK (XCSI_ISR_FR)
> > +
> > +#define XCSI_ISR_ALLINTR_MASK (XCSI_INTR_PROT_MASK |
> XCSI_INTR_PKTLVL_MASK |\
> > + XCSI_INTR_DPHY_MASK |
> XCSI_INTR_SPKT_MASK |\
> > + XCSI_INTR_ERR_MASK |
> XCSI_INTR_FRAMERCVD_MASK)
> > +
> > +/*
> > + * Removed VCXFE mask as it doesn't exist in IER
> > + * Removed STOP state irq as this will keep driver in irq handler
> > +only */
> > +#define XCSI_IER_INTR_MASK (XCSI_ISR_ALLINTR_MASK &\
> > + ~(XCSI_ISR_STOP | XCSI_ISR_VCXFE))
> > +
> > +#define XCSI_SPKTR_OFFSET 0x30
> > +#define XCSI_SPKTR_DATA GENMASK(23, 8)
> > +#define XCSI_SPKTR_VC GENMASK(7, 6)
> > +#define XCSI_SPKTR_DT GENMASK(5, 0)
> > +
> > +#define XCSI_VCXR_OFFSET 0x34
> > +#define XCSI_VCXR_VCERR GENMASK(23, 0)
> > +#define XCSI_VCXR_VCSTART 4
> > +#define XCSI_VCXR_VCEND 15
> > +#define XCSI_VCXR_FSYNCERR BIT(1)
> > +#define XCSI_VCXR_FLVLERR BIT(0)
> > +
> > +#define XCSI_CLKINFR_OFFSET 0x3C
> > +#define XCSI_CLKINFR_STOP BIT(1)
> > +
> > +#define XCSI_DLXINFR_OFFSET 0x40
> > +#define XCSI_DLXINFR_STOP BIT(5)
> > +#define XCSI_DLXINFR_SOTERR BIT(1)
> > +#define XCSI_DLXINFR_SOTSYNCERR BIT(0)
> > +#define XCSI_MAXDL_COUNT 0x4
> > +
> > +#define XCSI_VCXINF1R_OFFSET 0x60
> > +#define XCSI_VCXINF1R_LINECOUNT GENMASK(31, 16)
> > +#define XCSI_VCXINF1R_LINECOUNT_SHIFT 16
> > +#define XCSI_VCXINF1R_BYTECOUNT GENMASK(15, 0)
> > +
> > +#define XCSI_VCXINF2R_OFFSET 0x64
> > +#define XCSI_VCXINF2R_DT GENMASK(5, 0)
> > +#define XCSI_MAXVCX_COUNT 16
> > +
> > +/*
> > + * The core takes less than 100 video clock cycles to reset.
> > + * So choosing a timeout value larger than this.
> > + */
> > +#define XCSI_TIMEOUT_VAL 1000 /* us */
> > +
> > +/*
> > + * Sink pad connected to sensor source pad.
> > + * Source pad connected to next module like demosaic.
> > + */
> > +#define XCSI_MEDIA_PADS 2
> > +#define XCSI_DEFAULT_WIDTH 1920
> > +#define XCSI_DEFAULT_HEIGHT 1080
> > +
> > +/* Max media bus formats supported for enumeration */
> > +#define XCSI_MAX_MBUS_FMTS 16
> > +
> > +/* Max string length for CSI Data type string */
> > +#define XCSI_PXLFMT_STRLEN_MAX 16
> > +
> > +/* MIPI CSI2 Data Types from spec */
> > +#define XCSI_DT_YUV4228B 0x1E
> > +#define XCSI_DT_YUV42210B 0x1F
> > +#define XCSI_DT_RGB444 0x20
> > +#define XCSI_DT_RGB555 0x21
> > +#define XCSI_DT_RGB565 0x22
> > +#define XCSI_DT_RGB666 0x23
> > +#define XCSI_DT_RGB888 0x24
> > +#define XCSI_DT_RAW6 0x28
> > +#define XCSI_DT_RAW7 0x29
> > +#define XCSI_DT_RAW8 0x2A
> > +#define XCSI_DT_RAW10 0x2B
> > +#define XCSI_DT_RAW12 0x2C
> > +#define XCSI_DT_RAW14 0x2D
> > +#define XCSI_DT_RAW16 0x2E
> > +#define XCSI_DT_RAW20 0x2F
> > +
> > +#define XCSI_VCX_START 4
> > +#define XCSI_MAX_VC 4
> > +#define XCSI_MAX_VCX 16
> > +
> > +#define XCSI_NEXTREG_OFFSET 4
> > +
> > +/* There are 2 events frame sync and frame level error per VC */
> > +#define XCSI_VCX_NUM_EVENTS ((XCSI_MAX_VCX - XCSI_MAX_VC) *
> 2)
> > +
> > +/* Macro to return "true" or "false" string if bit is set */
> > +#define XCSI_GET_BITSET_STR(val, mask) (val) & (mask) ? "true" :
> "false"
> > +
> > +#define XADD_MBUS(state, mbus_fmt)
> \
> > + do { \
> > + if ((state)->mbus_fmts_count < XCSI_MAX_MBUS_FMTS) {
> \
> > + (state)->mbus_fmts[(state)->mbus_fmts_count++] =\
> > + (mbus_fmt); \
> > + } else { \
> > + dev_err((state)->core.dev, \
> > + "accessing array out of bounds!\n"); \
> > + } \
> > + } while (0)
> > +
> > +/**
> > + * struct xcsi2rxss_event - Event log structure
> > + * @mask: Event mask
> > + * @name: Name of the event
> > + */
> > +struct xcsi2rxss_event {
> > + u32 mask;
> > + const char *name;
> > +};
> > +
> > +static const struct xcsi2rxss_event xcsi2rxss_events[] = {
> > + { XCSI_ISR_FR, "Frame Received" },
> > + { XCSI_ISR_VCXFE, "VCX Frame Errors" },
> > + { XCSI_ISR_WCC, "Word Count Errors" },
> > + { XCSI_ISR_ILC, "Invalid Lane Count Error" },
> > + { XCSI_ISR_SPFIFOF, "Short Packet FIFO OverFlow Error" },
> > + { XCSI_ISR_SPFIFONE, "Short Packet FIFO Not Empty" },
> > + { XCSI_ISR_SLBF, "Streamline Buffer Full Error" },
> > + { XCSI_ISR_STOP, "Lane Stop State" },
> > + { XCSI_ISR_SOTERR, "SOT Error" },
> > + { XCSI_ISR_SOTSYNCERR, "SOT Sync Error" },
> > + { XCSI_ISR_ECC2BERR, "2 Bit ECC Unrecoverable Error" },
> > + { XCSI_ISR_ECC1BERR, "1 Bit ECC Recoverable Error" },
> > + { XCSI_ISR_CRCERR, "CRC Error" },
> > + { XCSI_ISR_DATAIDERR, "Data Id Error" },
> > + { XCSI_ISR_VC3FSYNCERR, "Virtual Channel 3 Frame Sync Error" },
> > + { XCSI_ISR_VC3FLVLERR, "Virtual Channel 3 Frame Level Error" },
> > + { XCSI_ISR_VC2FSYNCERR, "Virtual Channel 2 Frame Sync Error" },
> > + { XCSI_ISR_VC2FLVLERR, "Virtual Channel 2 Frame Level Error" },
> > + { XCSI_ISR_VC1FSYNCERR, "Virtual Channel 1 Frame Sync Error" },
> > + { XCSI_ISR_VC1FLVLERR, "Virtual Channel 1 Frame Level Error" },
> > + { XCSI_ISR_VC0FSYNCERR, "Virtual Channel 0 Frame Sync Error" },
> > + { XCSI_ISR_VC0FLVLERR, "Virtual Channel 0 Frame Level Error" } };
> > +
> > +#define XCSI_NUM_EVENTS ARRAY_SIZE(xcsi2rxss_events)
> > +
> > +/*
> > + * struct xcsi2rxss_core - Core configuration CSI2 Rx Subsystem
> > +device structure
> > + * @dev: Platform structure
> > + * @iomem: Base address of subsystem
> > + * @enable_active_lanes: If number of active lanes can be modified
> > + * @max_num_lanes: Maximum number of lanes present
> > + * @datatype: Data type filter
> > + * @events: counter for events
> > + * @vcx_events: counter for vcx_events
> > + * @en_vcx: If more than 4 VC are enabled
> > + * @clks: array of clocks
> > + * @num_clks: number of clocks
> > + * @rst_gpio: reset to video_aresetn
> > + */
> > +struct xcsi2rxss_core {
> > + struct device *dev;
> > + void __iomem *iomem;
> > + bool enable_active_lanes;
> > + u32 max_num_lanes;
> > + u32 datatype;
> > + u32 events[XCSI_NUM_EVENTS];
> > + u32 vcx_events[XCSI_VCX_NUM_EVENTS];
> > + bool en_vcx;
> > + struct clk_bulk_data *clks;
> > + int num_clks;
> > + struct gpio_desc *rst_gpio;
> > +};
> > +
> > +/**
> > + * struct xcsi2rxss_state - CSI2 Rx Subsystem device structure
> > + * @core: Core structure for MIPI CSI2 Rx Subsystem
> > + * @subdev: The v4l2 subdev structure
> > + * @format: Active V4L2 formats on each pad
> > + * @default_format: Default V4L2 format
> > + * @lock: mutex for accessing this structure
> > + * @pads: media pads
> > + * @mbus_fmts: List of media bus formats for enum_mbus_code
> > + * @mbus_fmts_count: Number of media bus formats
> > + * @streaming: Flag for storing streaming state
> > + *
> > + * This structure contains the device driver related parameters */
> > +struct xcsi2rxss_state {
> > + struct xcsi2rxss_core core;
> > + struct v4l2_subdev subdev;
> > + struct v4l2_mbus_framefmt format;
> > + struct v4l2_mbus_framefmt default_format;
> > + /* used to protect access to this struct */
> > + struct mutex lock;
> > + struct media_pad pads[XCSI_MEDIA_PADS];
> > + u32 mbus_fmts[XCSI_MAX_MBUS_FMTS];
> > + u32 mbus_fmts_count;
> > + bool streaming;
> > +};
> > +
> > +static const struct clk_bulk_data xcsi2rxss_clks[] = {
> > + { .id = "lite_aclk" },
> > + { .id = "video_aclk" },
> > +};
> > +
> > +static inline struct xcsi2rxss_state * to_xcsi2rxssstate(struct
> > +v4l2_subdev *subdev) {
> > + return container_of(subdev, struct xcsi2rxss_state, subdev); }
> > +
> > +/*
> > + * Register related operations
> > + */
> > +static inline u32 xcsi2rxss_read(struct xcsi2rxss_core *xcsi2rxss,
> > +u32 addr) {
> > + return ioread32(xcsi2rxss->iomem + addr); }
> > +
> > +static inline void xcsi2rxss_write(struct xcsi2rxss_core *xcsi2rxss, u32
> addr,
> > + u32 value)
> > +{
> > + iowrite32(value, xcsi2rxss->iomem + addr); }
> > +
> > +static inline void xcsi2rxss_clr(struct xcsi2rxss_core *xcsi2rxss, u32 addr,
> > + u32 clr)
> > +{
> > + xcsi2rxss_write(xcsi2rxss, addr,
> > + xcsi2rxss_read(xcsi2rxss, addr) & ~clr); }
> > +
> > +static inline void xcsi2rxss_set(struct xcsi2rxss_core *xcsi2rxss, u32 addr,
> > + u32 set)
> > +{
> > + xcsi2rxss_write(xcsi2rxss, addr,
> > + xcsi2rxss_read(xcsi2rxss, addr) | set);
>
> Fits on a single line.
Yes. I will fix in next version.
>
> > +}
> > +
> > +static void xcsi2rxss_enable(struct xcsi2rxss_core *core) {
> > + xcsi2rxss_set(core, XCSI_CCR_OFFSET, XCSI_CCR_ENABLE); }
> > +
> > +static void xcsi2rxss_disable(struct xcsi2rxss_core *core) {
> > + xcsi2rxss_clr(core, XCSI_CCR_OFFSET, XCSI_CCR_ENABLE); }
> > +
> > +static void xcsi2rxss_intr_enable(struct xcsi2rxss_core *core) {
> > + xcsi2rxss_clr(core, XCSI_GIER_OFFSET, XCSI_GIER_GIE);
> > + xcsi2rxss_write(core, XCSI_IER_OFFSET, XCSI_IER_INTR_MASK);
> > + xcsi2rxss_set(core, XCSI_GIER_OFFSET, XCSI_GIER_GIE); }
> > +
> > +static void xcsi2rxss_intr_disable(struct xcsi2rxss_core *core) {
> > + xcsi2rxss_clr(core, XCSI_IER_OFFSET, XCSI_IER_INTR_MASK);
> > + xcsi2rxss_clr(core, XCSI_GIER_OFFSET, XCSI_GIER_GIE); }
> > +
> > +/**
> > + * xcsi2rxss_reset - Does a soft reset of the MIPI CSI2 Rx Subsystem
> > + * @core: Core Xilinx CSI2 Rx Subsystem structure pointer
> > + *
> > + * Core takes less than 100 video clock cycles to reset.
> > + * So a larger timeout value is chosen for margin.
> > + *
> > + * Return: 0 - on success OR -ETIME if reset times out */ static int
> > +xcsi2rxss_reset(struct xcsi2rxss_core *core) {
> > + u32 timeout = XCSI_TIMEOUT_VAL;
> > +
> > + xcsi2rxss_set(core, XCSI_CCR_OFFSET, XCSI_CCR_SOFTRESET);
> > +
> > + while (xcsi2rxss_read(core, XCSI_CSR_OFFSET) & XCSI_CSR_RIPCD) {
> > + if (timeout == 0) {
> > + dev_err(core->dev, "soft reset timed out!\n");
> > + return -ETIME;
> > + }
> > +
> > + timeout--;
> > + udelay(1);
> > + }
> > +
> > + xcsi2rxss_clr(core, XCSI_CCR_OFFSET, XCSI_CCR_SOFTRESET);
> > + return 0;
> > +}
> > +
> > +static void xcsi2rxss_reset_event_counters(struct xcsi2rxss_state
> > +*state) {
> > + unsigned int i;
> > +
> > + for (i = 0; i < XCSI_NUM_EVENTS; i++)
> > + state->core.events[i] = 0;
> > +
> > + for (i = 0; i < XCSI_VCX_NUM_EVENTS; i++)
> > + state->core.vcx_events[i] = 0;
> > +}
> > +
> > +/* Print event counters */
> > +static void xcsi2rxss_log_counters(struct xcsi2rxss_state *state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > + unsigned int i;
> > +
> > + for (i = 0; i < XCSI_NUM_EVENTS; i++) {
> > + if (core->events[i] > 0) {
> > + dev_info(core->dev, "%s events: %d\n",
> > + xcsi2rxss_events[i].name,
> > + core->events[i]);
> > + }
> > + }
> > +
> > + if (core->en_vcx) {
> > + for (i = 0; i < XCSI_VCX_NUM_EVENTS; i++) {
> > + if (core->vcx_events[i] > 0) {
> > + dev_info(core->dev,
> > + "VC %d Frame %s err vcx events:
> %d\n",
> > + (i / 2) + XCSI_VCX_START,
> > + i & 1 ? "Sync" : "Level",
> > + core->vcx_events[i]);
> > + }
> > + }
> > + }
> > +}
> > +
> > +static void xcsi2rxss_log_ipconfig(struct xcsi2rxss_state *state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > +
> > + dev_dbg(core->dev, "****** Xilinx MIPI CSI2 Rx SS IP Config
> ******\n");
> > + dev_dbg(core->dev, "vcx is %s", core->en_vcx ? "enabled" :
> "disabled");
> > + dev_dbg(core->dev, "Enable active lanes property is %s\n",
> > + core->enable_active_lanes ? "present" : "absent");
> > + dev_dbg(core->dev, "Max lanes = %d", core->max_num_lanes);
> > + dev_dbg(core->dev, "Pixel format set as 0x%x\n", core->datatype);
> > + dev_dbg(core->dev,
> > +"**********************************************\n");
> > +}
> > +
> > +/**
> > + * xcsi2rxss_log_status - Logs the status of the CSI-2 Receiver
> > + * @sd: Pointer to V4L2 subdevice structure
> > + *
> > + * This function prints the current status of Xilinx MIPI CSI-2
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xcsi2rxss_log_status(struct v4l2_subdev *sd) {
> > + struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
> > + struct xcsi2rxss_core *core = &xcsi2rxss->core;
> > + u32 reg, data;
> > + unsigned int i, max_vc;
> > +
> > + mutex_lock(&xcsi2rxss->lock);
> > +
> > + xcsi2rxss_log_ipconfig(xcsi2rxss);
> > +
> > + xcsi2rxss_log_counters(xcsi2rxss);
> > +
> > + dev_info(core->dev, "***** Core Status *****\n");
> > + data = xcsi2rxss_read(core, XCSI_CSR_OFFSET);
> > + dev_info(core->dev, "Short Packet FIFO Full = %s\n",
> > + XCSI_GET_BITSET_STR(data, XCSI_CSR_SPFIFOFULL));
> > + dev_info(core->dev, "Short Packet FIFO Not Empty = %s\n",
> > + XCSI_GET_BITSET_STR(data, XCSI_CSR_SPFIFONE));
> > + dev_info(core->dev, "Stream line buffer full = %s\n",
> > + XCSI_GET_BITSET_STR(data, XCSI_CSR_SLBF));
> > + dev_info(core->dev, "Soft reset/Core disable in progress = %s\n",
> > + XCSI_GET_BITSET_STR(data, XCSI_CSR_RIPCD));
> > +
> > + /* Clk & Lane Info */
> > + dev_info(core->dev, "******** Clock Lane Info *********\n");
> > + data = xcsi2rxss_read(core, XCSI_CLKINFR_OFFSET);
> > + dev_info(core->dev, "Clock Lane in Stop State = %s\n",
> > + XCSI_GET_BITSET_STR(data, XCSI_CLKINFR_STOP));
> > +
> > + dev_info(core->dev, "******** Data Lane Info *********\n");
> > + dev_info(core->dev, "Lane\tSoT Error\tSoT Sync Error\tStop
> State\n");
> > + reg = XCSI_DLXINFR_OFFSET;
> > + for (i = 0; i < XCSI_MAXDL_COUNT; i++) {
> > + data = xcsi2rxss_read(core, reg);
> > +
> > + dev_info(core->dev, "%d\t%s\t\t%s\t\t%s\n", i,
> > + XCSI_GET_BITSET_STR(data, XCSI_DLXINFR_SOTERR),
> > + XCSI_GET_BITSET_STR(data,
> XCSI_DLXINFR_SOTSYNCERR),
> > + XCSI_GET_BITSET_STR(data, XCSI_DLXINFR_STOP));
> > +
> > + reg += XCSI_NEXTREG_OFFSET;
> > + }
> > +
> > + /* Virtual Channel Image Information */
> > + dev_info(core->dev, "********** Virtual Channel Info
> ************\n");
> > + dev_info(core->dev, "VC\tLine Count\tByte Count\tData Type\n");
> > + if (core->en_vcx)
> > + max_vc = XCSI_MAX_VCX;
> > + else
> > + max_vc = XCSI_MAX_VC;
> > +
> > + reg = XCSI_VCXINF1R_OFFSET;
> > + for (i = 0; i < max_vc; i++) {
> > + u32 line_count, byte_count, data_type;
> > +
> > + /* Get line and byte count from VCXINFR1 Register */
> > + data = xcsi2rxss_read(core, reg);
> > + byte_count = data & XCSI_VCXINF1R_BYTECOUNT;
> > + line_count = data & XCSI_VCXINF1R_LINECOUNT;
> > + line_count >>= XCSI_VCXINF1R_LINECOUNT_SHIFT;
> > +
> > + /* Get data type from VCXINFR2 Register */
> > + reg += XCSI_NEXTREG_OFFSET;
> > + data = xcsi2rxss_read(core, reg);
> > + data_type = data & XCSI_VCXINF2R_DT;
> > +
> > + dev_info(core->dev, "%d\t%d\t\t%d\t\t0x%x\n", i,
> line_count,
> > + byte_count, data_type);
> > +
> > + /* Move to next pair of VC Info registers */
> > + reg += XCSI_NEXTREG_OFFSET;
> > + }
> > +
> > + mutex_unlock(&xcsi2rxss->lock);
> > +
> > + return 0;
> > +}
> > +
> > +static int xcsi2rxss_start_stream(struct xcsi2rxss_state *state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > + int ret = 0;
> > +
> > + xcsi2rxss_enable(core);
> > +
> > + ret = xcsi2rxss_reset(core);
> > + if (ret < 0) {
> > + state->streaming = false;
> > + return ret;
> > + }
>
> You'll need to start streaming on the upstream sub-device somewhere in this
> function.
>
> > +
> > + xcsi2rxss_intr_enable(core);
> > + state->streaming = true;
> > +
> > + return ret;
> > +}
> > +
> > +static void xcsi2rxss_stop_stream(struct xcsi2rxss_state *state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > +
> > + xcsi2rxss_intr_disable(core);
> > + xcsi2rxss_disable(core);
> > + state->streaming = false;
>
> And stop it here.
Though this taken care by xvip_pipeline_start_stop() in xilinx-dma.c,
I will add the code here in next version.
>
> > +}
> > +
> > +/**
> > + * xcsi2rxss_irq_handler - Interrupt handler for CSI-2
> > + * @irq: IRQ number
> > + * @dev_id: Pointer to device state
> > + *
> > + * In the interrupt handler, a list of event counters are updated for
> > + * corresponding interrupts. This is useful to get status / debug.
> > + *
> > + * Return: IRQ_HANDLED after handling interrupts
> > + * IRQ_NONE is no interrupts
> > + */
> > +static irqreturn_t xcsi2rxss_irq_handler(int irq, void *dev_id) {
> > + struct xcsi2rxss_state *state = (struct xcsi2rxss_state *)dev_id;
> > + struct xcsi2rxss_core *core = &state->core;
> > + u32 status;
> > +
> > + status = xcsi2rxss_read(core, XCSI_ISR_OFFSET) &
> XCSI_ISR_ALLINTR_MASK;
> > + dev_dbg_ratelimited(core->dev, "interrupt status = 0x%08x\n",
> > +status);
> > +
> > + if (!status)
> > + return IRQ_NONE;
> > +
> > + /* Received a short packet */
> > + if (status & XCSI_ISR_SPFIFONE) {
> > + dev_dbg_ratelimited(core->dev, "Short packet = 0x%08x\n",
> > + xcsi2rxss_read(core, XCSI_SPKTR_OFFSET));
> > + }
> > +
> > + /* Short packet FIFO overflow */
> > + if (status & XCSI_ISR_SPFIFOF)
> > + dev_dbg_ratelimited(core->dev, "Short packet FIFO
> overflowed\n");
> > +
> > + /*
> > + * Stream line buffer full
> > + * This means there is a backpressure from downstream IP
> > + */
> > + if (status & XCSI_ISR_SLBF) {
> > + dev_alert_ratelimited(core->dev, "Stream Line Buffer
> Full!\n");
> > + xcsi2rxss_stop_stream(state);
> > + if (core->rst_gpio) {
> > + gpiod_set_value(core->rst_gpio, 1);
> > + /* minimum 40 dphy_clk_200M cycles */
> > + ndelay(250);
> > + gpiod_set_value(core->rst_gpio, 0);
> > + }
> > + }
> > +
> > + /* Increment event counters */
> > + if (status & XCSI_ISR_ALLINTR_MASK) {
> > + unsigned int i;
> > +
> > + for (i = 0; i < XCSI_NUM_EVENTS; i++) {
> > + if (!(status & xcsi2rxss_events[i].mask))
> > + continue;
> > + core->events[i]++;
> > + dev_dbg_ratelimited(core->dev, "%s: %d\n",
> > + xcsi2rxss_events[i].name,
> > + core->events[i]);
> > + }
> > +
> > + if (status & XCSI_ISR_VCXFE && core->en_vcx) {
> > + u32 vcxstatus;
> > +
> > + vcxstatus = xcsi2rxss_read(core, XCSI_VCXR_OFFSET);
> > + vcxstatus &= XCSI_VCXR_VCERR;
> > + for (i = 0; i < XCSI_VCX_NUM_EVENTS; i++) {
> > + if (!(vcxstatus & (1 << i)))
> > + continue;
> > + core->vcx_events[i]++;
> > + }
> > + xcsi2rxss_write(core, XCSI_VCXR_OFFSET, vcxstatus);
> > + }
> > + }
> > +
> > + xcsi2rxss_write(core, XCSI_ISR_OFFSET, status);
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/**
> > + * xcsi2rxss_s_stream - It is used to start/stop the streaming.
> > + * @sd: V4L2 Sub device
> > + * @enable: Flag (True / False)
> > + *
> > + * This function controls the start or stop of streaming for the
> > + * Xilinx MIPI CSI-2 Rx Subsystem.
> > + *
> > + * Return: 0 on success, errors otherwise */ static int
> > +xcsi2rxss_s_stream(struct v4l2_subdev *sd, int enable) {
> > + struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
> > + int ret = 0;
> > +
> > + mutex_lock(&xcsi2rxss->lock);
> > +
> > + if (enable) {
> > + if (!xcsi2rxss->streaming) {
> > + /* reset the event counters */
> > + xcsi2rxss_reset_event_counters(xcsi2rxss);
> > + ret = xcsi2rxss_start_stream(xcsi2rxss);
> > + }
> > + } else {
> > + if (xcsi2rxss->streaming) {
> > + struct gpio_desc *rst = xcsi2rxss->core.rst_gpio;
> > +
> > + xcsi2rxss_stop_stream(xcsi2rxss);
> > + if (rst) {
> > + gpiod_set_value_cansleep(rst, 1);
> > + usleep_range(1, 2);
> > + gpiod_set_value_cansleep(rst, 0);
> > + }
> > + }
> > + }
> > +
> > + mutex_unlock(&xcsi2rxss->lock);
> > + return ret;
> > +}
> > +
> > +static struct v4l2_mbus_framefmt *
> > +__xcsi2rxss_get_pad_format(struct xcsi2rxss_state *xcsi2rxss,
> > + struct v4l2_subdev_pad_config *cfg,
> > + unsigned int pad, u32 which)
> > +{
> > + switch (which) {
> > + case V4L2_SUBDEV_FORMAT_TRY:
> > + return v4l2_subdev_get_try_format(&xcsi2rxss->subdev, cfg,
> pad);
> > + case V4L2_SUBDEV_FORMAT_ACTIVE:
> > + return &xcsi2rxss->format;
> > + default:
> > + return NULL;
> > + }
> > +}
> > +
> > +/**
> > + * xcsi2rxss_get_format - Get the pad format
> > + * @sd: Pointer to V4L2 Sub device structure
> > + * @cfg: Pointer to sub device pad information structure
> > + * @fmt: Pointer to pad level media bus format
> > + *
> > + * This function is used to get the pad format information.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xcsi2rxss_get_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
> > +
> > + mutex_lock(&xcsi2rxss->lock);
> > + fmt->format = *__xcsi2rxss_get_pad_format(xcsi2rxss, cfg, fmt->pad,
> > + fmt->which);
> > + mutex_unlock(&xcsi2rxss->lock);
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xcsi2rxss_set_format - This is used to set the pad format
> > + * @sd: Pointer to V4L2 Sub device structure
> > + * @cfg: Pointer to sub device pad information structure
> > + * @fmt: Pointer to pad level media bus format
> > + *
> > + * This function is used to set the pad format. Since the pad format
> > +is fixed
> > + * in hardware, it can't be modified on run time. So when a format
> > +set is
> > + * requested by application, all parameters except the format type is
> > +saved
> > + * for the pad and the original pad format is sent back to the application.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xcsi2rxss_set_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *fmt)
> > +{
> > + struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
> > + struct xcsi2rxss_core *core = &xcsi2rxss->core;
> > + struct v4l2_mbus_framefmt *__format;
> > +
> > + /* only sink pad format can be updated */
> > + mutex_lock(&xcsi2rxss->lock);
> > +
> > + /*
> > + * Only the format->code parameter matters for CSI as the
> > + * CSI format cannot be changed at runtime.
> > + * Ensure that format to set is copied to over to CSI pad format
> > + */
> > + __format = __xcsi2rxss_get_pad_format(xcsi2rxss, cfg,
> > + fmt->pad, fmt->which);
> > +
> > + if (fmt->pad == XVIP_PAD_SOURCE) {
> > + fmt->format = *__format;
> > + mutex_unlock(&xcsi2rxss->lock);
> > + return 0;
> > + }
> > +
> > + /*
> > + * RAW8 is supported in all datatypes. So if requested media bus
> format
> > + * is of RAW8 type, then allow to be set. In case core is configured to
> > + * other RAW, YUV422 8/10 or RGB888, set appropriate media bus
> format.
> > + */
> > + if (!((fmt->format.code == MEDIA_BUS_FMT_SBGGR8_1X8 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGBRG8_1X8 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGRBG8_1X8 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SRGGB8_1X8) ||
> > + (core->datatype == XCSI_DT_RAW10 &&
> > + (fmt->format.code == MEDIA_BUS_FMT_SBGGR10_1X10 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGBRG10_1X10 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGRBG10_1X10 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SRGGB10_1X10)) ||
> > + (core->datatype == XCSI_DT_RAW12 &&
> > + (fmt->format.code == MEDIA_BUS_FMT_SBGGR12_1X12 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGBRG12_1X12 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGRBG12_1X12 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SRGGB12_1X12)) ||
> > + (core->datatype == XCSI_DT_RAW14 &&
> > + (fmt->format.code == MEDIA_BUS_FMT_SBGGR14_1X14 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGBRG14_1X14 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGRBG14_1X14 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SRGGB14_1X14)) ||
> > + (core->datatype == XCSI_DT_RAW16 &&
> > + (fmt->format.code == MEDIA_BUS_FMT_SBGGR16_1X16 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGBRG16_1X16 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SGRBG16_1X16 ||
> > + fmt->format.code == MEDIA_BUS_FMT_SRGGB16_1X16)) ||
> > + (core->datatype == XCSI_DT_YUV4228B &&
> > + fmt->format.code == MEDIA_BUS_FMT_UYVY8_1X16) ||
> > + (core->datatype == XCSI_DT_YUV42210B &&
> > + fmt->format.code == MEDIA_BUS_FMT_UYVY10_1X20) ||
> > + (core->datatype == XCSI_DT_RGB888 &&
> > + fmt->format.code == MEDIA_BUS_FMT_RBG888_1X24))) {
> > + /* Restore the original pad format code */
> > + dev_dbg(core->dev, "Unsupported media bus format");
> > + fmt->format.code = __format->code;
> > + }
> > +
> > + *__format = fmt->format;
>
> Did I already ask whether there are any limits on width or height for this
> device?
>
There is no limit on width and height from the protocol perspective.
> > + mutex_unlock(&xcsi2rxss->lock);
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > + * xcsi2rxss_enum_mbus_code - Handle pixel format enumeration
> > + * @sd : pointer to v4l2 subdev structure
> > + * @cfg: V4L2 subdev pad configuration
> > + * @code : pointer to v4l2_subdev_mbus_code_enum structure
> > + *
> > + * Return: -EINVAL or zero on success */ int
> > +xcsi2rxss_enum_mbus_code(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_mbus_code_enum *code) {
> > + struct xcsi2rxss_state *state = to_xcsi2rxssstate(sd);
> > +
> > + if (code->index >= state->mbus_fmts_count)
> > + return -EINVAL;
> > +
> > + code->code = state->mbus_fmts[code->index];
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * xcsi2rxss_open - Called on v4l2_open()
> > + * @sd: Pointer to V4L2 sub device structure
> > + * @fh: Pointer to V4L2 File handle
> > + *
> > + * This function is called on v4l2_open(). It sets the default format
> > + * for both pads.
> > + *
> > + * Return: 0 on success
> > + */
> > +static int xcsi2rxss_open(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_fh *fh)
> > +{
> > + struct xcsi2rxss_state *xcsi2rxss = to_xcsi2rxssstate(sd);
> > + struct v4l2_mbus_framefmt *format;
> > + unsigned int i;
> > +
> > + for (i = 0; i < XCSI_MEDIA_PADS; i++) {
> > + format = v4l2_subdev_get_try_format(sd, fh->pad, i);
> > + *format = xcsi2rxss->default_format;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +/*
> > +---------------------------------------------------------------------
> > +--------
> > + * Media Operations
> > + */
> > +
> > +static const struct media_entity_operations xcsi2rxss_media_ops = {
> > + .link_validate = v4l2_subdev_link_validate };
> > +
> > +static const struct v4l2_subdev_core_ops xcsi2rxss_core_ops = {
> > + .log_status = xcsi2rxss_log_status,
> > +};
> > +
> > +static const struct v4l2_subdev_video_ops xcsi2rxss_video_ops = {
> > + .s_stream = xcsi2rxss_s_stream
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops xcsi2rxss_pad_ops = {
> > + .get_fmt = xcsi2rxss_get_format,
> > + .set_fmt = xcsi2rxss_set_format,
> > + .enum_mbus_code = xcsi2rxss_enum_mbus_code,
>
> You'll need link_validate set to v4l2_subdev_link_validate_default here.
I will add this in the next version.
>
> > +};
> > +
> > +static const struct v4l2_subdev_ops xcsi2rxss_ops = {
> > + .core = &xcsi2rxss_core_ops,
> > + .video = &xcsi2rxss_video_ops,
> > + .pad = &xcsi2rxss_pad_ops
> > +};
> > +
> > +static const struct v4l2_subdev_internal_ops xcsi2rxss_internal_ops = {
> > + .open = xcsi2rxss_open,
> > +};
> > +
> > +static void xcsi2rxss_set_default_format(struct xcsi2rxss_state
> > +*state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > +
> > + memset(&state->default_format, 0, sizeof(state->default_format));
> > +
> > + switch (core->datatype) {
> > + case XCSI_DT_YUV4228B:
> > + state->default_format.code =
> MEDIA_BUS_FMT_UYVY8_1X16;
> > + break;
> > + case XCSI_DT_RGB888:
> > + state->default_format.code =
> MEDIA_BUS_FMT_RBG888_1X24;
> > + break;
> > + case XCSI_DT_YUV42210B:
> > + state->default_format.code =
> MEDIA_BUS_FMT_UYVY10_1X20;
> > + break;
> > + case XCSI_DT_RAW10:
> > + state->default_format.code =
> MEDIA_BUS_FMT_SRGGB10_1X10;
> > + break;
> > + case XCSI_DT_RAW12:
> > + state->default_format.code =
> MEDIA_BUS_FMT_SRGGB12_1X12;
> > + break;
> > + case XCSI_DT_RAW14:
> > + state->default_format.code =
> MEDIA_BUS_FMT_SRGGB14_1X14;
> > + break;
> > + case XCSI_DT_RAW16:
> > + state->default_format.code =
> MEDIA_BUS_FMT_SRGGB16_1X16;
> > + break;
> > + case XCSI_DT_RAW8:
> > + case XCSI_DT_RGB444:
> > + case XCSI_DT_RGB555:
> > + case XCSI_DT_RGB565:
> > + case XCSI_DT_RGB666:
> > + state->default_format.code =
> MEDIA_BUS_FMT_SRGGB8_1X8;
> > + break;
> > + }
> > +
> > + state->default_format.field = V4L2_FIELD_NONE;
> > + state->default_format.colorspace = V4L2_COLORSPACE_SRGB;
> > + state->default_format.width = XCSI_DEFAULT_WIDTH;
> > + state->default_format.height = XCSI_DEFAULT_HEIGHT;
> > +
> > + dev_dbg(core->dev, "default mediabus format = 0x%x",
> > + state->default_format.code);
> > +}
> > +
> > +static void xcsi2rxss_init_mbus_fmts(struct xcsi2rxss_state *state) {
> > + struct xcsi2rxss_core *core = &state->core;
> > +
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SRGGB8_1X8);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SBGGR8_1X8);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGRBG8_1X8);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGBRG8_1X8);
> > +
> > + switch (core->datatype) {
> > + case XCSI_DT_RAW10:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SRGGB10_1X10);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SBGGR10_1X10);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGRBG10_1X10);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGBRG10_1X10);
> > + break;
> > + case XCSI_DT_RAW12:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SRGGB12_1X12);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SBGGR12_1X12);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGRBG12_1X12);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGBRG12_1X12);
> > + break;
> > + case XCSI_DT_RAW14:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SRGGB14_1X14);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SBGGR14_1X14);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGRBG14_1X14);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGBRG14_1X14);
> > + break;
> > + case XCSI_DT_RAW16:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SRGGB16_1X16);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SBGGR16_1X16);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGRBG16_1X16);
> > + XADD_MBUS(state, MEDIA_BUS_FMT_SGBRG16_1X16);
> > + break;
> > + case XCSI_DT_YUV4228B:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_UYVY8_1X16);
> > + break;
> > + case XCSI_DT_RGB888:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_RBG888_1X24);
> > + break;
> > + case XCSI_DT_YUV42210B:
> > + XADD_MBUS(state, MEDIA_BUS_FMT_UYVY10_1X20);
> > + break;
> > + default:
> > + dev_err(core->dev, "Invalid data type!\n");
> > + }
> > +}
> > +
> > +static int xcsi2rxss_parse_of(struct xcsi2rxss_state *xcsi2rxss) {
> > + struct xcsi2rxss_core *core = &xcsi2rxss->core;
> > + struct device_node *node = xcsi2rxss->core.dev->of_node;
> > + struct device_node *ports = NULL;
> > + struct device_node *port = NULL;
> > + unsigned int nports, irq;
> > + bool en_csi_v20, vfb;
> > + int ret;
> > +
> > + en_csi_v20 = of_property_read_bool(node, "xlnx,en-csi-v2-0");
> > + if (en_csi_v20)
> > + core->en_vcx = of_property_read_bool(node, "xlnx,en-vcx");
> > +
> > + core->enable_active_lanes =
> > + of_property_read_bool(node, "xlnx,en-active-lanes");
> > +
> > + ret = of_property_read_u32(node, "xlnx,csi-pxl-format",
> > + &core->datatype);
> > + if (ret < 0) {
> > + dev_err(core->dev, "missing xlnx,csi-pxl-format property\n");
> > + return ret;
> > + }
> > +
> > + switch (core->datatype) {
> > + case XCSI_DT_YUV4228B:
> > + case XCSI_DT_RGB444:
> > + case XCSI_DT_RGB555:
> > + case XCSI_DT_RGB565:
> > + case XCSI_DT_RGB666:
> > + case XCSI_DT_RGB888:
> > + case XCSI_DT_RAW6:
> > + case XCSI_DT_RAW7:
> > + case XCSI_DT_RAW8:
> > + case XCSI_DT_RAW10:
> > + case XCSI_DT_RAW12:
> > + case XCSI_DT_RAW14:
> > + break;
> > + case XCSI_DT_YUV42210B:
> > + case XCSI_DT_RAW16:
> > + case XCSI_DT_RAW20:
> > + if (!en_csi_v20) {
> > + ret = -EINVAL;
> > + dev_dbg(core->dev, "enable csi v2 for this pixel
> format");
> > + }
> > + break;
> > + default:
> > + ret = -EINVAL;
> > + }
> > + if (ret < 0) {
> > + dev_err(core->dev, "invalid csi-pxl-format property!\n");
> > + return ret;
> > + }
> > +
> > + vfb = of_property_read_bool(node, "xlnx,vfb");
> > + if (!vfb) {
> > + dev_err(core->dev, "failed as VFB is disabled!\n");
> > + return -EINVAL;
> > + }
> > +
> > + ports = of_get_child_by_name(node, "ports");
> > + if (!ports)
> > + ports = node;
> > +
> > + nports = 0;
> > + for_each_child_of_node(ports, port) {
> > + struct device_node *endpoint;
> > + struct v4l2_fwnode_endpoint v4lendpoint;
> > + int ret;
> > +
> > + if (!port->name || of_node_cmp(port->name, "port"))
> > + continue;
> > +
> > + endpoint = of_get_next_child(port, NULL);
> > + if (!endpoint) {
> > + dev_err(core->dev, "No port at\n");
> > + return -EINVAL;
> > + }
>
> You shouldn't parse the graph data structure yourself.
>
> Could you use fwnode_graph_get_endpoint_by_id(), and work it from there
> without using an enumeration? You have two endpoints in there after all in
> two ports.
>
> Please see drivers/media/pci/intel/ipu3/ipu3-cio2.c for an example.
>
Thanks for sharing this. I will update accordingly in next version.
> > +
> > + /*
> > + * since first port is sink port and it contains
> > + * all info about data-lanes and cfa-pattern,
> > + * don't parse second port but only check if exists
> > + */
> > + if (nports == XVIP_PAD_SOURCE) {
> > + dev_dbg(core->dev, "no need to parse source port");
> > + nports++;
> > + of_node_put(endpoint);
> > + continue;
> > + }
> > +
> > + ret =
> v4l2_fwnode_endpoint_parse(of_fwnode_handle(endpoint),
> > + &v4lendpoint);
>
> Please set the bus_type to what you need on that port, e.g.
> V4L2_MBUS_CSI2_DPHY, and set the rest to zero.
>
Ok will do this too.
> > + of_node_put(endpoint);
> > + if (ret)
> > + return ret;
> > +
> > + dev_dbg(core->dev, "%s : port %d bus type = %d\n",
> > + __func__, nports, v4lendpoint.bus_type);
> > +
> > + if (v4lendpoint.bus_type == V4L2_MBUS_CSI2_DPHY) {
> > + dev_dbg(core->dev, "%s : base.port = %d base.id =
> %d\n",
> > + __func__, v4lendpoint.base.port,
> > + v4lendpoint.base.id);
> > +
> > + dev_dbg(core->dev, "%s : mipi number lanes =
> %d\n",
> > + __func__,
> > + v4lendpoint.bus.mipi_csi2.num_data_lanes);
> > +
> > + core->max_num_lanes =
> > + v4lendpoint.bus.mipi_csi2.num_data_lanes;
> > + }
> > +
> > + /* Count the number of ports. */
> > + nports++;
> > + }
> > +
> > + if (nports != XCSI_MEDIA_PADS) {
> > + dev_err(core->dev, "invalid number of ports %u\n", nports);
> > + return -EINVAL;
> > + }
> > +
> > + /* Register interrupt handler */
> > + irq = irq_of_parse_and_map(node, 0);
> > + ret = devm_request_irq(core->dev, irq, xcsi2rxss_irq_handler,
> > + IRQF_SHARED, "xilinx-csi2rxss", xcsi2rxss);
> > + if (ret) {
> > + dev_err(core->dev, "Err = %d Interrupt handler reg
> failed!\n",
> > + ret);
> > + return ret;
> > + }
> > +
> > + xcsi2rxss_log_ipconfig(xcsi2rxss);
> > +
> > + return 0;
> > +}
> > +
> > +static int xcsi2rxss_probe(struct platform_device *pdev) {
> > + struct v4l2_subdev *subdev;
> > + struct xcsi2rxss_state *xcsi2rxss;
> > + struct xcsi2rxss_core *core;
> > + struct resource *res;
> > + int ret;
> > +
> > + xcsi2rxss = devm_kzalloc(&pdev->dev, sizeof(*xcsi2rxss),
> GFP_KERNEL);
> > + if (!xcsi2rxss)
> > + return -ENOMEM;
> > +
> > + core = &xcsi2rxss->core;
> > + core->dev = &pdev->dev;
> > +
> > + core->clks = devm_kmemdup(core->dev, xcsi2rxss_clks,
> > + sizeof(xcsi2rxss_clks), GFP_KERNEL);
> > + if (!core->clks)
> > + return -ENOMEM;
> > +
> > + /* Reset GPIO */
> > + core->rst_gpio = devm_gpiod_get_optional(core->dev, "reset",
> > + GPIOD_OUT_HIGH);
> > + if (IS_ERR(core->rst_gpio)) {
> > + if (PTR_ERR(core->rst_gpio) != -EPROBE_DEFER)
> > + dev_err(core->dev, "Video Reset GPIO not setup in
> DT");
> > + return PTR_ERR(core->rst_gpio);
> > + }
> > +
> > + mutex_init(&xcsi2rxss->lock);
> > +
> > + ret = xcsi2rxss_parse_of(xcsi2rxss);
> > + if (ret < 0)
> > + return ret;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + core->iomem = devm_ioremap_resource(core->dev, res);
> > + if (IS_ERR(core->iomem))
> > + return PTR_ERR(core->iomem);
> > +
> > + core->num_clks = ARRAY_SIZE(xcsi2rxss_clks);
>
> num_clks never changes, please drop it and use ARRAY_SIZE(...) instead.
Right. I will drop num_clks from core in next version and use ARRAY_SIZE().
>
> > +
> > + ret = clk_bulk_get(core->dev, core->num_clks, core->clks);
> > + if (ret)
> > + return ret;
> > +
> > + ret = clk_bulk_prepare_enable(core->num_clks, core->clks);
> > + if (ret)
> > + goto err_clk_put;
> > +
> > + if (core->rst_gpio) {
> > + gpiod_set_value_cansleep(core->rst_gpio, 1);
> > + /* minimum of 40 dphy_clk_200M cycles */
> > + usleep_range(1, 2);
> > + gpiod_set_value_cansleep(core->rst_gpio, 0);
> > + }
> > +
> > + xcsi2rxss_reset(core);
> > +
> > + /* Initialize V4L2 subdevice and media entity */
> > + xcsi2rxss->pads[XVIP_PAD_SINK].flags = MEDIA_PAD_FL_SINK;
> > + xcsi2rxss->pads[XVIP_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE;
> > +
> > + /* Initialize the default format */
> > + xcsi2rxss_set_default_format(xcsi2rxss);
> > +
> > + /* Initialize the mbus formats supported */
> > + xcsi2rxss_init_mbus_fmts(xcsi2rxss);
> > +
> > + /* Initialize V4L2 subdevice and media entity */
> > + subdev = &xcsi2rxss->subdev;
> > + v4l2_subdev_init(subdev, &xcsi2rxss_ops);
> > + subdev->dev = &pdev->dev;
> > + subdev->internal_ops = &xcsi2rxss_internal_ops;
> > + strscpy(subdev->name, dev_name(&pdev->dev), sizeof(subdev-
> >name));
> > + subdev->flags |= V4L2_SUBDEV_FL_HAS_EVENTS |
> V4L2_SUBDEV_FL_HAS_DEVNODE;
> > + subdev->entity.ops = &xcsi2rxss_media_ops;
> > + v4l2_set_subdevdata(subdev, xcsi2rxss);
> > +
> > + ret = media_entity_pads_init(&subdev->entity, XCSI_MEDIA_PADS,
> > + xcsi2rxss->pads);
> > + if (ret < 0)
> > + goto error;
> > +
> > + platform_set_drvdata(pdev, xcsi2rxss);
> > +
> > + ret = v4l2_async_register_subdev(subdev);
> > + if (ret < 0) {
> > + dev_err(core->dev, "failed to register subdev\n");
> > + goto error;
> > + }
> > +
> > + dev_info(core->dev, "Xilinx CSI2 Rx Subsystem device found!\n");
> > +
> > + return 0;
> > +error:
> > + media_entity_cleanup(&subdev->entity);
> > + mutex_destroy(&xcsi2rxss->lock);
> > + clk_bulk_disable_unprepare(core->num_clks, core->clks);
> > +err_clk_put:
> > + clk_bulk_put(core->num_clks, core->clks);
> > + return ret;
> > +}
> > +
> > +static int xcsi2rxss_remove(struct platform_device *pdev) {
> > + struct xcsi2rxss_state *xcsi2rxss = platform_get_drvdata(pdev);
> > + struct xcsi2rxss_core *core = &xcsi2rxss->core;
> > + struct v4l2_subdev *subdev = &xcsi2rxss->subdev;
> > +
> > + v4l2_async_unregister_subdev(subdev);
> > + media_entity_cleanup(&subdev->entity);
> > + mutex_destroy(&xcsi2rxss->lock);
> > + clk_bulk_disable_unprepare(core->num_clks, core->clks);
> > + clk_bulk_put(core->num_clks, core->clks);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id xcsi2rxss_of_id_table[] = {
> > + { .compatible = "xlnx,mipi-csi2-rx-subsystem-4.0", },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, xcsi2rxss_of_id_table);
> > +
> > +static struct platform_driver xcsi2rxss_driver = {
> > + .driver = {
> > + .name = "xilinx-csi2rxss",
> > + .of_match_table = xcsi2rxss_of_id_table,
> > + },
> > + .probe = xcsi2rxss_probe,
> > + .remove = xcsi2rxss_remove,
> > +};
> > +
> > +module_platform_driver(xcsi2rxss_driver);
> > +
> > +MODULE_AUTHOR("Vishal Sagar <vsagar@xxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Xilinx MIPI CSI2 Rx Subsystem Driver");
> > +MODULE_LICENSE("GPL v2");
>
> This does not align with the SPDX header. v2 or v2+?
I will change the SPDX header to GPL-v2.0 as it is similar to other files in this folder.
Regards
Vishal Sagar
>
> --
> Regards,
>
> Sakari Ailus
