Re: [PATCH v2 07/10] PCIe: qcom: fix init problem with missing PARF programming

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Ansuel,

Please fix the patch subject for all patches in the series per Bjorn H.
request.

PCI: qcom: Fix init problem with missing PARF programming

Also the patch subject is misleading to me. Actually you change few phy
parameters: Tx De-Emphasis, Tx Swing and Rx equalization. On the other
side I guess those parameters are board specific and I'm not sure how
this change will reflect on apq8064 boards.

On 4/2/20 3:11 PM, Ansuel Smith wrote:
> PARF programming was missing and this cause initilizzation problem on
> some ipq806x based device (Netgear R7800 for example). This cause a
> total lock of the system on kernel load.
> 
> Fixes: 82a82383 PCI: qcom: Add Qualcomm PCIe controller driver
> Signed-off-by: Ansuel Smith <ansuelsmth@xxxxxxxxx>
> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 48 +++++++++++++++++++++-----
>  1 file changed, 39 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 211a1aa7d0f1..77b1ab7e23a3 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -46,6 +46,9 @@
>  
>  #define PCIE20_PARF_PHY_CTRL			0x40
>  #define PCIE20_PARF_PHY_REFCLK			0x4C
> +#define REF_SSP_EN				BIT(16)
> +#define REF_USE_PAD				BIT(12)

Could you rename this to:

PHY_REFCLK_SSP_EN
PHY_REFCLK_USE_PAD

> +
>  #define PCIE20_PARF_DBI_BASE_ADDR		0x168
>  #define PCIE20_PARF_SLV_ADDR_SPACE_SIZE		0x16C
>  #define PCIE20_PARF_MHI_CLOCK_RESET_CTRL	0x174
> @@ -77,6 +80,18 @@
>  #define DBI_RO_WR_EN				1
>  
>  #define PERST_DELAY_US				1000
> +/* PARF registers */
> +#define PCIE20_PARF_PCS_DEEMPH			0x34
> +#define PCS_DEEMPH_TX_DEEMPH_GEN1(x)		(x << 16)
> +#define PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(x)	(x << 8)
> +#define PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(x)	(x << 0)
> +
> +#define PCIE20_PARF_PCS_SWING			0x38
> +#define PCS_SWING_TX_SWING_FULL(x)		(x << 8)
> +#define PCS_SWING_TX_SWING_LOW(x)		(x << 0)
> +
> +#define PCIE20_PARF_CONFIG_BITS		0x50
> +#define PHY_RX0_EQ(x)				(x << 24)
>  
>  #define PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE	0x358
>  #define SLV_ADDR_SPACE_SZ			0x10000000
> @@ -184,6 +199,16 @@ struct qcom_pcie {
>  
>  #define to_qcom_pcie(x)		dev_get_drvdata((x)->dev)
>  
> +static inline void qcom_clear_and_set_dword(void __iomem *addr,

drop 'inline' the compiler is smart enough to decide.

> +				 u32 clear_mask, u32 set_mask)
> +{
> +	u32 val = readl(addr);
> +
> +	val &= ~clear_mask;
> +	val |= set_mask;
> +	writel(val, addr);
> +}
> +

If you add such function you should introduce it in a separate patch and
use it in the whole driver where it is applicable. After that we can see
what is the benefit of it.

>  static void qcom_ep_reset_assert(struct qcom_pcie *pcie)
>  {
>  	gpiod_set_value_cansleep(pcie->reset, 1);
> @@ -304,7 +329,6 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
>  	struct qcom_pcie_resources_2_1_0 *res = &pcie->res.v2_1_0;
>  	struct dw_pcie *pci = pcie->pci;
>  	struct device *dev = pci->dev;
> -	u32 val;
>  	int ret;
>  
>  	ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
> @@ -355,15 +379,21 @@ static int qcom_pcie_init_2_1_0(struct qcom_pcie *pcie)
>  		goto err_deassert_ahb;
>  	}
>  
> -	/* enable PCIe clocks and resets */
> -	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> -	val &= ~BIT(0);
> -	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +	qcom_clear_and_set_dword(pcie->parf + PCIE20_PARF_PHY_CTRL, BIT(0), 0);

please keep the comment.

> +
> +	/* PARF programming */

pointless comment, please drop it.

> +	writel(PCS_DEEMPH_TX_DEEMPH_GEN1(0x18) |
> +	       PCS_DEEMPH_TX_DEEMPH_GEN2_3_5DB(0x18) |
> +	       PCS_DEEMPH_TX_DEEMPH_GEN2_6DB(0x22),
> +	       pcie->parf + PCIE20_PARF_PCS_DEEMPH);
> +	writel(PCS_SWING_TX_SWING_FULL(0x78) |
> +	       PCS_SWING_TX_SWING_LOW(0x78),
> +	       pcie->parf + PCIE20_PARF_PCS_SWING);
> +	writel(PHY_RX0_EQ(0x4), pcie->parf + PCIE20_PARF_CONFIG_BITS);
>  
> -	/* enable external reference clock */
> -	val = readl(pcie->parf + PCIE20_PARF_PHY_REFCLK);
> -	val |= BIT(16);
> -	writel(val, pcie->parf + PCIE20_PARF_PHY_REFCLK);
> +	/* enable reference clock */

Why you dropped 'external' ?

> +	qcom_clear_and_set_dword(pcie->parf + PCIE20_PARF_PHY_REFCLK,
> +		      REF_USE_PAD, REF_SSP_EN);
>  
>  	ret = reset_control_deassert(res->phy_reset);
>  	if (ret) {
> 

-- 
regards,
Stan



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux