On Tue, Mar 17, 2020 at 04:17:06PM +0100, Christophe Roullier wrote:
> Convert stm32 dwmac to DT schema.
>
> Signed-off-by: Christophe Roullier <christophe.roullier@xxxxxx>
> ---
> .../devicetree/bindings/net/stm32-dwmac.txt | 44 -----
> .../devicetree/bindings/net/stm32-dwmac.yaml | 160 ++++++++++++++++++
> 2 files changed, 160 insertions(+), 44 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/net/stm32-dwmac.txt
> create mode 100644 Documentation/devicetree/bindings/net/stm32-dwmac.yaml
>
> diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt
> deleted file mode 100644
> index a90eef11dc46..000000000000
> --- a/Documentation/devicetree/bindings/net/stm32-dwmac.txt
> +++ /dev/null
> @@ -1,44 +0,0 @@
> -STMicroelectronics STM32 / MCU DWMAC glue layer controller
> -
> -This file documents platform glue layer for stmmac.
> -Please see stmmac.txt for the other unchanged properties.
> -
> -The device node has following properties.
> -
> -Required properties:
> -- compatible: For MCU family should be "st,stm32-dwmac" to select glue, and
> - "snps,dwmac-3.50a" to select IP version.
> - For MPU family should be "st,stm32mp1-dwmac" to select
> - glue, and "snps,dwmac-4.20a" to select IP version.
> -- clocks: Must contain a phandle for each entry in clock-names.
> -- clock-names: Should be "stmmaceth" for the host clock.
> - Should be "mac-clk-tx" for the MAC TX clock.
> - Should be "mac-clk-rx" for the MAC RX clock.
> - For MPU family need to add also "ethstp" for power mode clock
> -- interrupt-names: Should contain a list of interrupt names corresponding to
> - the interrupts in the interrupts property, if available.
> - Should be "macirq" for the main MAC IRQ
> - Should be "eth_wake_irq" for the IT which wake up system
> -- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which
> - encompases the glue register, and the offset of the control register.
> -
> -Optional properties:
> -- clock-names: For MPU family "eth-ck" for PHY without quartz
> -- st,eth-clk-sel (boolean) : set this property in RGMII PHY when you want to select RCC clock instead of ETH_CLK125.
> -- st,eth-ref-clk-sel (boolean) : set this property in RMII mode when you have PHY without crystal 50MHz and want to select RCC clock instead of ETH_REF_CLK.
> -
> -Example:
> -
> - ethernet@40028000 {
> - compatible = "st,stm32-dwmac", "snps,dwmac-3.50a";
> - reg = <0x40028000 0x8000>;
> - reg-names = "stmmaceth";
> - interrupts = <0 61 0>, <0 62 0>;
> - interrupt-names = "macirq", "eth_wake_irq";
> - clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
> - clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>;
> - st,syscon = <&syscfg 0x4>;
> - snps,pbl = <8>;
> - snps,mixed-burst;
> - dma-ranges;
> - };
> diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.yaml b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
> new file mode 100644
> index 000000000000..4440216917b3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
> @@ -0,0 +1,160 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +# Copyright 2019 BayLibre, SAS
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/net/stm32-dwmac.yaml#";
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#";
> +
> +title: STMicroelectronics STM32 / MCU DWMAC glue layer controller
> +
> +maintainers:
> + - Alexandre Torgue <alexandre.torgue@xxxxxx>
> + - Christophe Roullier <christophe.roullier@xxxxxx>
> +
> +description:
> + This file documents platform glue layer for stmmac.
> +
> +# We need a select here so we don't match all nodes with 'snps,dwmac'
> +select:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - st,stm32-dwmac
> + - st,stm32mp1-dwmac
> + required:
> + - compatible
> +
> +allOf:
> + - $ref: "snps,dwmac.yaml#"
> + - if:
> + properties:
> + compatible:
> + contains:
> + enum:
> + - st,stm32-dwmac
> + - st,stm32mp1-dwmac
This schema is only applied when these compatibles are present, so you
don't need the 'if' and all this can move to the main section.
> + then:
> + properties:
> + clocks:
> + minItems: 3
> + maxItems: 5
> + items:
> + - description: GMAC main clock
> + - description: MAC TX clock
> + - description: MAC RX clock
> + - description: For MPU family, used for power mode
> + - description: For MPU family, used for PHY without quartz
> +
> + clock-names:
> + minItems: 3
> + maxItems: 5
> + contains:
> + enum:
> + - stmmaceth
> + - mac-clk-tx
> + - mac-clk-rx
> + - ethstp
> + - eth-ck
> +
> +properties:
> + compatible:
> + oneOf:
> + - items:
> + - enum:
> + - st,stm32mp1-dwmac
> + - const: snps,dwmac-4.20a
> + - items:
> + - enum:
> + - st,stm32-dwmac
> + - const: snps,dwmac-4.10a
> + - items:
> + - enum:
> + - st,stm32-dwmac
> + - const: snps,dwmac-3.50a
> +
> + st,syscon:
> + allOf:
> + - $ref: "/schemas/types.yaml#/definitions/phandle-array"
> + description:
> + Should be phandle/offset pair. The phandle to the syscon node which
> + encompases the glue register, and the offset of the control register
> +
> + st,eth-clk-sel:
> + description:
> + set this property in RGMII PHY when you want to select RCC clock instead of ETH_CLK125.
> + type: boolean
> +
> + st,eth-ref-clk-sel:
> + description:
> + set this property in RMII mode when you have PHY without crystal 50MHz and want to
> + select RCC clock instead of ETH_REF_CLK.
> + type: boolean
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - st,syscon
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/clock/stm32mp1-clks.h>
> + #include <dt-bindings/reset/stm32mp1-resets.h>
> + #include <dt-bindings/mfd/stm32h7-rcc.h>
> + //Example 1
> + ethernet0: ethernet@5800a000 {
> + compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
> + reg = <0x5800a000 0x2000>;
> + reg-names = "stmmaceth";
> + interrupts = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "macirq";
> + clock-names = "stmmaceth",
> + "mac-clk-tx",
> + "mac-clk-rx",
> + "ethstp",
> + "eth-ck";
> + clocks = <&rcc ETHMAC>,
> + <&rcc ETHTX>,
> + <&rcc ETHRX>,
> + <&rcc ETHSTP>,
> + <&rcc ETHCK_K>;
> + st,syscon = <&syscfg 0x4>;
> + snps,pbl = <2>;
> + snps,axi-config = <&stmmac_axi_config_0>;
> + snps,tso;
> + status = "disabled";
Don't show status in examples.
> + phy-mode = "rgmii";
> + };
Wrong indentation.
> +
> + //Example 2 (MCU example)
> + ethernet1: ethernet@40028000 {
> + compatible = "st,stm32-dwmac", "snps,dwmac-3.50a";
> + reg = <0x40028000 0x8000>;
> + reg-names = "stmmaceth";
> + interrupts = <0 61 0>, <0 62 0>;
> + interrupt-names = "macirq", "eth_wake_irq";
> + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
> + clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>;
> + st,syscon = <&syscfg 0x4>;
> + snps,pbl = <8>;
> + snps,mixed-burst;
> + dma-ranges;
> + phy-mode = "mii";
> + };
> +
> + //Example 3
> + ethernet2: ethernet@40027000 {
> + compatible = "st,stm32-dwmac", "snps,dwmac-4.10a";
> + reg = <0x40028000 0x8000>;
> + reg-names = "stmmaceth";
> + interrupts = <61>;
> + interrupt-names = "macirq";
> + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx";
> + clocks = <&rcc 62>, <&rcc 61>, <&rcc 60>;
> + st,syscon = <&syscfg 0x4>;
> + snps,pbl = <8>;
> + status = "disabled";
> + phy-mode = "mii";
> + };
> --
> 2.17.1
>
