Re: [PATCH v2 6/6] dt-bindings: iio: Add adis16475 documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Mar 16, 2020 at 01:53:12PM +0100, Nuno Sá wrote:
> Document the ADIS16475 device devicetree bindings.
> 
> Signed-off-by: Nuno Sá <nuno.sa@xxxxxxxxxx>
> ---
> Changes in v2:
>  * Remove burst32 property;
>  * Rename clk-mode to adi,sync-mode;
>  * Remove clock-names;
>  * Add conditionals to state that clocks is only needed depending on adi,sync-mode property
> 
>  .../bindings/iio/imu/adi,adis16475.yaml       | 146 ++++++++++++++++++
>  MAINTAINERS                                   |   1 +
>  2 files changed, 147 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
> 
> diff --git a/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml b/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
> new file mode 100644
> index 000000000000..9eeb42773edd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
> @@ -0,0 +1,146 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/imu/adi,adis16475.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Analog Devices ADIS16475 and similar IMUs
> +
> +maintainers:
> +  - Nuno Sá <nuno.sa@xxxxxxxxxx>
> +
> +description: |
> +  Analog Devices ADIS16475 and similar IMUs
> +  https://www.analog.com/media/en/technical-documentation/data-sheets/ADIS16475.pdf
> +
> +properties:
> +  compatible:
> +    enum:
> +      - adi,adis16475-1
> +      - adi,adis16475-2
> +      - adi,adis16475-3
> +      - adi,adis16477-1
> +      - adi,adis16477-2
> +      - adi,adis16477-3
> +      - adi,adis16470
> +      - adi,adis16465-1
> +      - adi,adis16465-2
> +      - adi,adis16465-3
> +      - adi,adis16467-1
> +      - adi,adis16467-2
> +      - adi,adis16467-3
> +      - adi,adis16500
> +      - adi,adis16505-1
> +      - adi,adis16505-2
> +      - adi,adis16505-3
> +      - adi,adis16507-1
> +      - adi,adis16507-2
> +      - adi,adis16507-3
> +
> +  reg:
> +    maxItems: 1
> +
> +  spi-cpha: true
> +
> +  spi-cpol: true
> +
> +  spi-max-frequency:
> +    maximum: 2000000
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  reset-gpios:
> +    description:
> +      Must be the device tree identifier of the RESET pin. If specified,
> +      it will be asserted during driver probe. As the line is active low,
> +      it should be marked GPIO_ACTIVE_LOW.
> +    maxItems: 1
> +
> +  adi,sync-mode:
> +    description:
> +      Configures the device SYNC pin. The following modes are supported
> +      0 - output_sync
> +      1 - direct_sync
> +      2 - scaled_sync
> +      3 - pulse_sync
> +    allOf:
> +      - $ref: /schemas/types.yaml#/definitions/uint32
> +    minimum: 0
> +    maximum: 3
> +
> +  adi,scaled-output-hz:
> +    description:
> +      This property must be present if the clock mode is scaled-sync through
> +      clock-names property. In this mode, the input clock can have a range
> +      of 1Hz to 128HZ which must be scaled to originate an allowable sample
> +      rate. This property specifies that rate.
> +    minimum: 1900
> +    maximum: 2100
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - spi-cpha
> +  - spi-cpol
> +
> +if:
> +  properties:
> +    compatible:
> +      contains:
> +        enum:
> +          - adi,adis16500
> +          - adi,adis16505-1
> +          - adi,adis16505-2
> +          - adi,adis16505-3
> +          - adi,adis16507-1
> +          - adi,adis16507-2
> +          - adi,adis16507-3
> +
> +then:
> +  properties:
> +    adi,sync-mode:
> +      minimum: 0
> +      maximum: 2
> +
> +  if:
> +    properties:
> +      adi,sync-mode:
> +        enum: [1, 2]
> +
> +  then:
> +    dependencies:
> +      adi,sync-mode: [ clocks ]

You can remove this if/then if you...

> +
> +else:

> +  if:
> +    properties:
> +      adi,sync-mode:
> +        enum: [1, 2, 3]
> +
> +  then:
> +    dependencies:
> +      adi,sync-mode: [ clocks ]

...put this if by itself under an 'allOf'. (And then the 1st if should 
go under the 'allOf' too).

> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    spi {
> +            #address-cells = <1>;
> +            #size-cells = <0>;
> +
> +            adis16475: adis16475-3@0 {
> +                    compatible = "adi,adis16475-3";
> +                    reg = <0>;
> +                    spi-cpha;
> +                    spi-cpol;
> +                    spi-max-frequency = <2000000>;
> +                    interrupts = <4 IRQ_TYPE_EDGE_RISING>;
> +                    interrupt-parent = <&gpio>;
> +            };
> +    };
> +...
> diff --git a/MAINTAINERS b/MAINTAINERS
> index f11262f1f3bb..f8ccc92ab378 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -1015,6 +1015,7 @@ W:	http://ez.analog.com/community/linux-device-drivers
>  S:	Supported
>  F:	drivers/iio/imu/adis16475.c
>  F:	Documentation/ABI/testing/sysfs-bus-iio-imu-adis16475
> +F:	Documentation/devicetree/bindings/iio/imu/adi,adis16475.yaml
>  
>  ANALOG DEVICES INC ADM1177 DRIVER
>  M:	Beniamin Bia <beniamin.bia@xxxxxxxxxx>
> -- 
> 2.25.1
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux