Re: [PATCH v5 2/6] PCI: iproc: Add INTx support with better modeling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2020-03-26 06:48, Srinath Mannam wrote:
From: Ray Jui <ray.jui@xxxxxxxxxxxx>

Add PCIe legacy interrupt INTx support to the iProc PCIe driver by
modeling it with its own IRQ domain. All 4 interrupts INTA, INTB, INTC,
INTD share the same interrupt line connected to the GIC in the system,
while the status of each INTx can be obtained through the INTX CSR
register.

Signed-off-by: Ray Jui <ray.jui@xxxxxxxxxxxx>
Signed-off-by: Srinath Mannam <srinath.mannam@xxxxxxxxxxxx>
Reviewed-by: Andrew Murray <andrew.murray@xxxxxxx>
---
drivers/pci/controller/pcie-iproc.c | 147 +++++++++++++++++++++++++++++++++++-
 drivers/pci/controller/pcie-iproc.h |   8 ++
 2 files changed, 153 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/controller/pcie-iproc.c
b/drivers/pci/controller/pcie-iproc.c
index 0a468c7..62d8f43 100644
--- a/drivers/pci/controller/pcie-iproc.c
+++ b/drivers/pci/controller/pcie-iproc.c
@@ -14,6 +14,7 @@
 #include <linux/delay.h>
 #include <linux/interrupt.h>
 #include <linux/irqchip/arm-gic-v3.h>
+#include <linux/irqchip/chained_irq.h>
 #include <linux/platform_device.h>
 #include <linux/of_address.h>
 #include <linux/of_pci.h>
@@ -270,6 +271,7 @@ enum iproc_pcie_reg {

 	/* enable INTx */
 	IPROC_PCIE_INTX_EN,
+	IPROC_PCIE_INTX_CSR,

 	/* outbound address mapping */
 	IPROC_PCIE_OARR0,
@@ -314,6 +316,7 @@ static const u16 iproc_pcie_reg_paxb_bcma[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_LINK_STATUS]	= 0xf0c,
 };

@@ -325,6 +328,7 @@ static const u16 iproc_pcie_reg_paxb[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_OARR0]		= 0xd20,
 	[IPROC_PCIE_OMAP0]		= 0xd40,
 	[IPROC_PCIE_OARR1]		= 0xd28,
@@ -341,6 +345,7 @@ static const u16 iproc_pcie_reg_paxb_v2[] = {
 	[IPROC_PCIE_CFG_ADDR]		= 0x1f8,
 	[IPROC_PCIE_CFG_DATA]		= 0x1fc,
 	[IPROC_PCIE_INTX_EN]		= 0x330,
+	[IPROC_PCIE_INTX_CSR]		= 0x334,
 	[IPROC_PCIE_OARR0]		= 0xd20,
 	[IPROC_PCIE_OMAP0]		= 0xd40,
 	[IPROC_PCIE_OARR1]		= 0xd28,
@@ -846,9 +851,142 @@ static int iproc_pcie_check_link(struct iproc_pcie *pcie)
 	return link_is_active ? 0 : -ENODEV;
 }

-static void iproc_pcie_enable(struct iproc_pcie *pcie)
+static void iproc_pcie_mask_irq(struct irq_data *d)
 {
+	struct iproc_pcie *pcie = irq_data_get_irq_chip_data(d);
+	u32 val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&pcie->intx_lock, flags);

As Arnd already noticed, this needs to be defined as  a raw spinlock.

+	val =  iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_EN);
+	val &= ~(BIT(irqd_to_hwirq(d)));
+	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, val);
+	spin_unlock_irqrestore(&pcie->intx_lock, flags);
+}
+
+static void iproc_pcie_unmask_irq(struct irq_data *d)
+{
+	struct iproc_pcie *pcie = irq_data_get_irq_chip_data(d);
+	u32 val;
+	unsigned long flags;
+
+	spin_lock_irqsave(&pcie->intx_lock, flags);
+	val =  iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_EN);
+	val |= (BIT(irqd_to_hwirq(d)));
+	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, val);
+	spin_unlock_irqrestore(&pcie->intx_lock, flags);
+}
+
+static struct irq_chip iproc_pcie_irq_chip = {
+	.name = "pcie-iproc-intc",
+	.irq_enable = iproc_pcie_unmask_irq,
+	.irq_disable = iproc_pcie_mask_irq,

No. Either the enable/disable callbacks are different from unmask/mask,
or they don't exist.

- A disabled interrupt is free to loose pending interrupts
- A masked interrupt doesn't loose interrupts.

I'm pretty sure yours is the latter.

+	.irq_mask = iproc_pcie_mask_irq,
+	.irq_unmask = iproc_pcie_unmask_irq,
+};
+
+static int iproc_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
+			       irq_hw_number_t hwirq)
+{
+ irq_set_chip_and_handler(irq, &iproc_pcie_irq_chip, handle_level_irq);
+	irq_set_chip_data(irq, domain->host_data);
+
+	return 0;
+}
+
+static const struct irq_domain_ops intx_domain_ops = {
+	.map = iproc_pcie_intx_map,
+};
+
+static void iproc_pcie_isr(struct irq_desc *desc)
+{
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	struct iproc_pcie *pcie;
+	struct device *dev;
+	unsigned long status;
+	u32 bit, virq;
+
+	chained_irq_enter(chip, desc);
+	pcie = irq_desc_get_handler_data(desc);
+	dev = pcie->dev;
+
+	/* go through INTx A, B, C, D until all interrupts are handled */
+	do {
+		status = iproc_pcie_read_reg(pcie, IPROC_PCIE_INTX_CSR);
+		for_each_set_bit(bit, &status, PCI_NUM_INTX) {
+			virq = irq_find_mapping(pcie->irq_domain, bit);
+			if (virq)
+				generic_handle_irq(virq);
+			else
+				dev_err(dev, "unexpected INTx%u\n", bit);

I'd rather you avoid this kind of unlimited console screaming in interrupt context. Either ratelimit it, or even better turn it into a debug statement.

+		}
+	} while ((status & SYS_RC_INTX_MASK) != 0);
+
+	chained_irq_exit(chip, desc);
+}
+
+static int iproc_pcie_intx_enable(struct iproc_pcie *pcie)
+{
+	struct device *dev = pcie->dev;
+	struct device_node *node;
+	int ret;
+
+	/*
+	 * BCMA devices do not map INTx the same way as platform devices. All
+	 * BCMA needs below line to enable INTx
+	 */
 	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, SYS_RC_INTX_MASK);
+
+	node = of_get_compatible_child(dev->of_node, "brcm,iproc-intc");
+	if (node)
+		pcie->irq = of_irq_get(node, 0);
+
+	if (!node || pcie->irq <= 0)
+		return 0;
+
+	spin_lock_init(&pcie->intx_lock);
+
+	/* set IRQ handler */
+	irq_set_chained_handler_and_data(pcie->irq, iproc_pcie_isr, pcie);

Please do this last, once the domain is allocated (you leave a window where
a screaming interrupt can fire here).

+
+	/* add IRQ domain for INTx */
+	pcie->irq_domain = irq_domain_add_linear(node, PCI_NUM_INTX,
+						 &intx_domain_ops, pcie);
+	if (!pcie->irq_domain) {
+		dev_err(dev, "failed to add INTx IRQ domain\n");
+		ret = -ENOMEM;
+		goto err_rm_handler_data;
+	}
+
+	return 0;
+
+err_rm_handler_data:
+	of_node_put(node);
+	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);
+
+	return ret;
+}
+
+static void iproc_pcie_intx_disable(struct iproc_pcie *pcie)
+{
+	uint32_t offset, virq;
+	unsigned long flags;
+
+	spin_lock_irqsave(&pcie->intx_lock, flags);
+	iproc_pcie_write_reg(pcie, IPROC_PCIE_INTX_EN, 0x0);
+	spin_unlock_irqrestore(&pcie->intx_lock, flags);

What's the reason for this lock/unlock? What are you racing against?

+
+	if (pcie->irq <= 0)
+		return;
+
+	for (offset = 0; offset < PCI_NUM_INTX; offset++) {
+		virq = irq_find_mapping(pcie->irq_domain, offset);
+		if (virq)
+			irq_dispose_mapping(virq);
+	}
+
+	irq_domain_remove(pcie->irq_domain);
+	irq_set_chained_handler_and_data(pcie->irq, NULL, NULL);

The other way around: first you disconnect the interrupt, then you
free the data that the interrupt can make use of.

 }

 static inline bool iproc_pcie_ob_is_valid(struct iproc_pcie *pcie,
@@ -1518,7 +1656,11 @@ int iproc_pcie_setup(struct iproc_pcie *pcie,
struct list_head *res)
 		goto err_power_off_phy;
 	}

-	iproc_pcie_enable(pcie);
+	ret = iproc_pcie_intx_enable(pcie);
+	if (ret) {
+		dev_err(dev, "failed to enable INTx\n");
+		goto err_power_off_phy;
+	}

 	if (IS_ENABLED(CONFIG_PCI_MSI))
 		if (iproc_pcie_msi_enable(pcie))
@@ -1562,6 +1704,7 @@ int iproc_pcie_remove(struct iproc_pcie *pcie)
 	pci_remove_root_bus(pcie->root_bus);

 	iproc_pcie_msi_disable(pcie);
+	iproc_pcie_intx_disable(pcie);

 	phy_power_off(pcie->phy);
 	phy_exit(pcie->phy);
diff --git a/drivers/pci/controller/pcie-iproc.h
b/drivers/pci/controller/pcie-iproc.h
index 4f03ea5..787bfba 100644
--- a/drivers/pci/controller/pcie-iproc.h
+++ b/drivers/pci/controller/pcie-iproc.h
@@ -74,9 +74,13 @@ struct iproc_msi;
  * @ib: inbound mapping related parameters
  * @ib_map: outbound mapping region related parameters
  *
+ * @irq: interrupt line wired to the generic GIC for INTx
+ * @irq_domain: IRQ domain for INTx
+ *
* @need_msi_steer: indicates additional configuration of the iProc PCIe * controller is required to steer MSI writes to external interrupt controller
  * @msi: MSI data
+ * @intx_lock: spinlock to protect access to INTx related registers
  */
 struct iproc_pcie {
 	struct device *dev;
@@ -102,8 +106,12 @@ struct iproc_pcie {
 	struct iproc_pcie_ib ib;
 	const struct iproc_pcie_ib_map *ib_map;

+	int irq;
+	struct irq_domain *irq_domain;
+
 	bool need_msi_steer;
 	struct iproc_msi *msi;
+	spinlock_t intx_lock;
 };

 int iproc_pcie_setup(struct iproc_pcie *pcie, struct list_head *res);

Thanks,

        M.
--
Jazz is not dead. It just smells funny...



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux