From: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
Currently neither clocksource nor scheduler clock kernel framework
support the clocks with variable frequency. Needless to say how many
problems may cause the sudden base clocks frequency change. In a
simplest case the system time will either slow down or speed up.
Since on CM2.5 and earlier MIPS GIC timer is synchronously clocked
with CPU we must set some limitations on using it for these frameworks
if CPU frequency may change. First of all it's not safe to have the
MIPS GIC used for scheduler timings. So we shouldn't proceed with
the clocks registration in the sched-subsystem. Secondly we must
significantly decrease the MIPS GIC clocksource rating. This will let
the system to use it only as a last resort.
Note CM3.x-based systems may also experience the problems with MIPS GIC
if the CPU-frequency change is activated for the whole CPU cluster
instead of using the individual CPC core clocks divider.
Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
Cc: Alexey Malahov <Alexey.Malahov@xxxxxxxxxxxxxxxxxxxx>
Cc: Thomas Bogendoerfer <tsbogend@xxxxxxxxxxxxxxxx>
Cc: Paul Burton <paulburton@xxxxxxxxxx>
Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>
Cc: Thomas Gleixner <tglx@xxxxxxxxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
Cc: Rob Herring <robh+dt@xxxxxxxxxx>
Cc: Mark Rutland <mark.rutland@xxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
---
drivers/clocksource/mips-gic-timer.c | 13 +++++++++----
1 file changed, 9 insertions(+), 4 deletions(-)
diff --git a/drivers/clocksource/mips-gic-timer.c b/drivers/clocksource/mips-gic-timer.c
index 8239ff99cfe4..5eb241b8b28d 100644
--- a/drivers/clocksource/mips-gic-timer.c
+++ b/drivers/clocksource/mips-gic-timer.c
@@ -185,7 +185,10 @@ static int __init __gic_clocksource_init(void)
gic_clocksource.mask = CLOCKSOURCE_MASK(count_width);
/* Calculate a somewhat reasonable rating value. */
- gic_clocksource.rating = 200 + gic_frequency / 10000000;
+ if (mips_cm_revision() >= CM_REV_CM3 || !IS_ENABLED(CONFIG_CPU_FREQ))
+ gic_clocksource.rating = 200 + gic_frequency / 10000000;
+ else
+ gic_clocksource.rating = 99;
ret = clocksource_register_hz(&gic_clocksource, gic_frequency);
if (ret < 0)
@@ -239,9 +242,11 @@ static int __init gic_clocksource_of_init(struct device_node *node)
/* And finally start the counter */
clear_gic_config(GIC_CONFIG_COUNTSTOP);
- sched_clock_register(mips_cm_is64 ?
- gic_read_count_64 : gic_read_count_2x32,
- 64, gic_frequency);
+ if (mips_cm_revision() >= CM_REV_CM3 || !IS_ENABLED(CONFIG_CPU_FREQ)) {
+ sched_clock_register(mips_cm_is64 ?
+ gic_read_count_64 : gic_read_count_2x32,
+ 64, gic_frequency);
+ }
return 0;
}
--
2.25.1
