[PATCH v2 08/10] arm64: dts: renesas: salvator: add a connection from adv748x codec (HDMI input) to the R-Car SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



As all known variants of the Salvator board have the HDMI decoder
chip (the ADV7482) connected to the SSI4 on R-Car SoC, the ADV7482
endpoint and the connection definitions are placed in the common board
file.
For the same reason, the CLK_C clock line and I2C configuration (similar
to the ak4613, on the same interface) are added into the common file.

Signed-off-by: Alexander Riesen <alexander.riesen@xxxxxxxxxxx>
Reviewed-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>

--

v2:

Also add ssi4_ctrl pin group in the sound pins. The pins are
responsible for SCK4 (sample clock) WS4 and (word boundary input),
and are required for SSI audio input over I2S.

Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>

The adv748x shall provide its own implementation of the output clock
(MCLK), connected to the audio_clk_c line of the R-Car SoC.

If the frequency of the ADV748x MCLK were fixed, the clock
implementation were not necessary, but it does not seem so: the MCLK
depends on the value in a speed multiplier register and the input sample
rate (48kHz).

Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>

Remove audio clock C from the clocks of adv7482.

The clocks property of the video-receiver node lists the input
clocks of the device, which is quite the opposite from the
original intention: the adv7482 on Salvator X boards is a
provide of the MCLK clock for I2S audio output.

Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>

Remove old definition of &sound_card.dais and reduce size of changes
in the Salvator-X specific device tree source.

Declare video-receiver a clock producer, as the adv748x driver
implements the master clock used I2S audio output.

Suggested-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>

The driver provides only MCLK clock, not the SCLK and LRCLK,
which are part of the I2S protocol.

Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
---
 .../boot/dts/renesas/r8a77950-salvator-x.dts  |  3 +-
 .../boot/dts/renesas/salvator-common.dtsi     | 47 +++++++++++++++++--
 2 files changed, 44 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
index 2438825c9b22..e16c146808b6 100644
--- a/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77950-salvator-x.dts
@@ -146,7 +146,8 @@ &sata {
 &sound_card {
 	dais = <&rsnd_port0	/* ak4613 */
 		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2>;	/* HDMI1  */
+		&rsnd_port2	/* HDMI1  */
+		&rsnd_port3>;	/* adv7482 hdmi-in  */
 };
 
 &usb2_phy2 {
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index 98bbcafc8c0d..ead7f8d7a929 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -460,7 +460,7 @@ pca9654: gpio@20 {
 		#gpio-cells = <2>;
 	};
 
-	video-receiver@70 {
+	adv7482_hdmi_in: video-receiver@70 {
 		compatible = "adi,adv7482";
 		reg = <0x70 0x71 0x72 0x73 0x74 0x75
 		       0x60 0x61 0x62 0x63 0x64 0x65>;
@@ -469,6 +469,7 @@ video-receiver@70 {
 
 		#address-cells = <1>;
 		#size-cells = <0>;
+		#clock-cells = <0>; /* the MCLK for I2S output */
 
 		interrupt-parent = <&gpio6>;
 		interrupt-names = "intrq1", "intrq2";
@@ -510,6 +511,15 @@ adv7482_txb: endpoint {
 				remote-endpoint = <&csi20_in>;
 			};
 		};
+
+		port@c {
+			reg = <12>;
+
+			adv7482_i2s: endpoint {
+				remote-endpoint = <&rsnd_endpoint3>;
+				system-clock-direction-out;
+			};
+		};
 	};
 
 	csa_vdd: adc@7c {
@@ -684,7 +694,8 @@ sdhi3_pins_uhs: sd3_uhs {
 	};
 
 	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
+			 "ssi4_data", "ssi4_ctrl";
 		function = "ssi";
 	};
 
@@ -733,8 +744,8 @@ &rcar_sound {
 	pinctrl-0 = <&sound_pins &sound_clk_pins>;
 	pinctrl-names = "default";
 
-	/* Single DAI */
-	#sound-dai-cells = <0>;
+	/* multi DAI */
+	#sound-dai-cells = <1>;
 
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
@@ -758,8 +769,19 @@ &rcar_sound {
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
+		 <&adv7482_hdmi_in>,
 		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+	clock-names = "ssi-all",
+		      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+		      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+		      "ssi.1", "ssi.0",
+		      "src.9", "src.8", "src.7", "src.6",
+		      "src.5", "src.4", "src.3", "src.2",
+		      "src.1", "src.0",
+		      "mix.1", "mix.0",
+		      "ctu.1", "ctu.0",
+		      "dvc.0", "dvc.1",
+		      "clk_a", "clk_b", "clk_c", "clk_i";
 
 	ports {
 		#address-cells = <1>;
@@ -777,6 +799,21 @@ rsnd_endpoint0: endpoint {
 				capture  = <&ssi1 &src1 &dvc1>;
 			};
 		};
+		rsnd_port3: port@3 {
+			reg = <3>;
+			rsnd_endpoint3: endpoint {
+				remote-endpoint = <&adv7482_i2s>;
+
+				dai-tdm-slot-num = <8>;
+				dai-tdm-slot-width = <32>;
+				dai-format = "left_j";
+				mclk-fs = <256>;
+				bitclock-master = <&adv7482_i2s>;
+				frame-master = <&adv7482_i2s>;
+
+				capture = <&ssi4>;
+			};
+		};
 	};
 };
 
-- 
2.25.1.25.g9ecbe7eb18





[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux