[PATCH 3/3] ARM: dts: kirkwood: add kirkwood-km_fixedeth DTS file

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Besides our Kirkwood Reference design, there is another group of board
on which the eth interface is not connected to a phy but to a swtich for
some board internal communication.

The configuration of the switch is handled by an EEPROM or by the
bootloader, but on the kirkwood side, the port is always configured as
1000 Mbits, full duplex.

Signed-off-by: Valentin Longchamp <valentin.longchamp@xxxxxxxxxxx>

---

 arch/arm/boot/dts/kirkwood-km_fixedeth.dts | 70 ++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 arch/arm/boot/dts/kirkwood-km_fixedeth.dts

diff --git a/arch/arm/boot/dts/kirkwood-km_fixedeth.dts b/arch/arm/boot/dts/kirkwood-km_fixedeth.dts
new file mode 100644
index 0000000..3d54d9b
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-km_fixedeth.dts
@@ -0,0 +1,70 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-98dx4122.dtsi"
+
+/ {
+	model = "Keymile Kirkwood Fixed Eth";
+	compatible = "keymile,km_fixedeth", "marvell,kirkwood-98DX4122", "marvell,kirkwood";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		stdout-path = &uart0;
+	};
+
+	mbus {
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				status = "okay";
+			};
+		};
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-0 = < &pmx_i2c_gpio_sda &pmx_i2c_gpio_scl >;
+			pinctrl-names = "default";
+
+			pmx_i2c_gpio_sda: pmx-gpio-sda {
+				marvell,pins = "mpp8";
+				marvell,function = "gpio";
+			};
+			pmx_i2c_gpio_scl: pmx-gpio-scl {
+				marvell,pins = "mpp9";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "ok";
+		};
+	};
+
+	i2c@0 {
+		compatible = "i2c-gpio";
+		gpios = < &gpio0 8 GPIO_ACTIVE_HIGH		/* sda */
+			  &gpio0 9 GPIO_ACTIVE_HIGH>;		/* scl */
+		i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <25>;
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <>;
+		speed = <1000>;  /* <SPEED_1000> */
+		duplex = <0x01>; /* <DUPLEX_FULL> */
+	};
+};
-- 
1.8.0.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux