Hi, On Thursday 15 May 2014 12:32 PM, Sebastian Hesselbarth wrote: > On 05/15/2014 08:45 AM, Kishon Vijay Abraham I wrote: >> On Thursday 15 May 2014 12:12 AM, Sebastian Hesselbarth wrote: >>> On 05/14/2014 08:12 PM, Arnd Bergmann wrote: >>>> On Wednesday 14 May 2014 19:57:46 Sebastian Hesselbarth wrote: >>>>> On 05/14/2014 06:57 PM, Antoine Ténart wrote: >>>>>> On Wed, May 14, 2014 at 06:11:24PM +0200, Arnd Bergmann wrote: >>>>>>> On Wednesday 14 May 2014 17:49:29 Antoine Ténart wrote: >>>>>>>> On Wed, May 14, 2014 at 05:31:24PM +0200, Arnd Bergmann wrote: > [...] >>>>> Now, thinking about the PHY binding and the (possible) multi-protocol >>>>> support, it can be possible that on BG2Q there is a generic 2-lane >>>>> LVDS PHY that can be configured to support SATA or PCIe. Both are >>>>> electrically and bit-level compatible, so they could be internally >>>>> wired-up with AHCI and PCIe controller. >>>> >>>> Sounds like a reasonable guess. We have other PHY drivers doing the >>>> same thing already. > [...] >>>>> From a DT point-of-view, we need a way to (a) link each SATA or PCIe >>>>> port to the PHY, (b) specify the PHY lane to be used, and (c) specify >>>>> the protocol to be used on that lane. If I got it right, Arnd already >>>>> mentioned to use the phy-specifier to deal with it: >>>>> >>>>> e.g. phy = <&genphy 0 MODE_SATA> or phy = <&genphy 1 MODE_PCIE> >>>> >>>> Right. >>>> >>>>> Let's assume we have one dual-port SATA controller and one PCIe >>>>> controller with either x1 or x2 support. The only sane DT binding, >>>>> I can think of then would be: >>>>> >>>>> berlin2q.dtsi: >>>>> >>>>> genphy: lvds@ea00ff { >>>>> compatible = "marvell,berlin-lvds-phy"; >>>>> reg = <0xea00ff 0x100>; >>>>> #phy-cells = <2>; >>>>> }; >>>>> >>>>> sata: sata@ab00ff { >>>>> compatible = "ahci-platform"; >>>>> reg = <0xab00ff 0x100>; >>>>> >>>>> sata0: sata-port@0 { >>>>> reg = <0>; >>>>> phy = <&genphy 0 MODE_SATA>; >>>>> status = "disabled"; >>>>> }; >>>>> >>>>> sata1: sata-port@1 { >>>>> reg = <1>; >>>>> phy = <&genphy 1 MODE_SATA>; >>>>> status = "disabled"; >>>>> }; >>>>> }; >>>>> >>>>> pcie: pcie@ab01ff { >>>>> compatible = "marvell,berlin-pcie"; >>>>> reg = <0xab01ff 0x100>; >>>>> >>>>> pcie0: pcie-port@0 { >>>>> reg = <0>; >>>>> /* set phy on a per-board basis */ >>>>> /* PCIe x1 on Lane 0 : phy = <&genphy 0 MODE_PCIE>; */ >>>>> /* PCIe x2 on Lane 0 and 1 : phy = <&genphy 0 MODE_PCIE>, <&genphy 1 >>>>> MODE_PCIE>; */ >>>>> status = "disabled"; >>>>> }; >>>>> }; >>>>> >>>>> berlin2q-dmp.dts: >>>>> >>>>> &sata1 { >>>>> status = "okay"; >>>>> }; >>>>> >>>>> &pcie0 { >>>>> phy = <&genphy 1 MODE_PCIE>; >>>>> }; >>>>> >>>>> berlin2q-foo.dts: >>>>> >>>>> &pcie0 { >>>>> phy = <&genphy 0 MODE_PCIE>, <&genphy 1 MODE_PCIE>; >>>>> }; >>>> >>>> Exactly. I would also be fine with keeping the sub-nodes of the >>>> phy device as in v3 and using #phy-cells=<1> instead of #phy-cells. >>>> The result would be pretty much the same, it just depends on how >>>> closely connected the two logical phys are. >> >> huh.. even with sub-nodes you'll need #phy-cells=<2> if we use a single *PHY >> PROVIDER*. Because with just PHYs node pointer we won't be able to get the PHY. >> We'll need PHY providers node pointer. >> >> However I'd prefer to have sub-nodes for each individual PHYs and register a >> single PHY PROVIDER. > > Depends on what you call PHY. In the example above the PHY is what > allows you to control both lanes. > > So you want sub-nodes for each individual lane given the nomenclature > of the example? > > Or like it is used in the example above, a single PHY node with an index > in the phy-specifier to pick an individual lane. > > IMHO, having both phy-specifier index _and_ PHY sub-node per lane > has no benefit at all. You cannot even use the PHY sub-nodes for any > setup properties, as they depend on the consumer claiming the lane. IMO the dt data should completely describe the HW. So just by looking at the PHY node, we won't be able to tell the no of PHYs implemented in the IP if we have a single PHY node (In this case the lanes in the IP). However if you think it's an overkill for having sub-nodes for each lane then single PHY node is fine too. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html