On Tue, Mar 10, 2020 at 1:36 AM Shawn Guo <shawnguo@xxxxxxxxxx> wrote:
>
> On Thu, Feb 20, 2020 at 06:02:06AM -0600, Adam Ford wrote:
> > Beacon Embeddedworks is launching a development kit based on the
> > i.MX8M Mini SoC. The kit consists of a System on Module (SOM)
> > + baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard
> > has an wm8962 audio CODEC, a single USB OTG, and three USB host ports.
> >
> > Signed-off-by: Adam Ford <aford173@xxxxxxxxx>
> >
> > diff --git a/arch/arm64/boot/dts/freescale/beacon-imx8mm-baseboard.dtsi b/arch/arm64/boot/dts/freescale/beacon-imx8mm-baseboard.dtsi
> > new file mode 100644
> > index 000000000000..6f6a3e8ebb91
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/beacon-imx8mm-baseboard.dtsi
> > @@ -0,0 +1,289 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2020 Compass Electronics Group, LLC
> > + */
> > +
> > +/ {
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + led0 {
> > + label = "gen_led0";
> > + gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
> > + default-state = "none";
> > + };
> > +
> > + led1 {
> > + label = "gen_led1";
> > + gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
> > + default-state = "none";
> > + };
> > +
> > + led2 {
> > + label = "gen_led2";
> > + gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
> > + default-state = "none";
> > + };
> > +
> > + led3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_led3>;
> > + label = "heartbeat";
> > + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +
> > + reg_audio: regulator-audio {
> > + compatible = "regulator-fixed";
> > + regulator-name = "3v3_aud";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + reg_usdhc2_vmmc: regulator-usdhc2 {
> > + compatible = "regulator-fixed";
> > + regulator-name = "VSD_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > + };
> > +
> > + sound {
> > + compatible = "fsl,imx-audio-wm8962";
> > + model = "wm8962-audio";
> > + audio-cpu = <&sai3>;
> > + audio-codec = <&wm8962>;
> > + audio-routing =
> > + "Headphone Jack", "HPOUTL",
> > + "Headphone Jack", "HPOUTR",
> > + "Ext Spk", "SPKOUTL",
> > + "Ext Spk", "SPKOUTR",
> > + "AMIC", "MICBIAS",
> > + "IN3R", "AMIC";
> > + };
> > +};
> > +
> > +&ecspi2 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_espi2>;
> > + status = "okay";
>
> 'status' goes to the last of property list.
>
> > + cs-gpios = <&gpio5 9 0>;
> > +
> > + at25@0 {
> > + compatible = "atmel,at25";
> > + reg = <0>;
> > + spi-max-frequency = <5000000>;
> > + spi-cpha;
> > + spi-cpol;
> > +
>
> Drop the newline.
>
> > + pagesize = <32>;
> > + size = <2048>;
> > + address-width = <16>;
> > + };
> > +};
> > +
> > +&i2c2 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c2>;
> > + status = "okay";
> > +};
> > +
> > +&i2c4 {
> > +
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c4>;
>
> Two names with only one pinctrl handle?
>
> > + status = "okay";
> > +
> > + pca6416_0: gpio@20 {
> > + compatible = "nxp,pcal6416";
> > + reg = <0x20>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pcal6414>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupt-parent = <&gpio4>;
> > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +
> > + pca6416_1: gpio@21 {
> > + compatible = "nxp,pcal6416";
> > + reg = <0x21>;
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + interrupt-parent = <&gpio4>;
> > + interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +
> > + wm8962: audio-codec@1a {
>
> Sort the nodes in unit-address.
>
> > + compatible = "wlf,wm8962";
> > + reg = <0x1a>;
> > + clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
> > + clock-names = "xclk";
> > + DCVDD-supply = <®_audio>;
> > + DBVDD-supply = <®_audio>;
> > + AVDD-supply = <®_audio>;
> > + CPVDD-supply = <®_audio>;
> > + MICVDD-supply = <®_audio>;
> > + PLLVDD-supply = <®_audio>;
> > + SPKVDD1-supply = <®_audio>;
> > + SPKVDD2-supply = <®_audio>;
> > + gpio-cfg = <
> > + 0x0000 /* 0:Default */
> > + 0x0000 /* 1:Default */
> > + 0x0000 /* 2:FN_DMICCLK */
> > + 0x0000 /* 3:Default */
> > + 0x0000 /* 4:FN_DMICCDAT */
> > + 0x0000 /* 5:Default */
> > + >;
> > + };
> > +};
> > +
> > +&sai3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_sai3>;
> > + assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> > + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> > + assigned-clock-rates = <24576000>;
> > + fsl,sai-mclk-direction-output;
> > + status = "okay";
> > +};
> > +
> > +&snvs_pwrkey {
> > + status = "okay";
> > +};
> > +
> > +&uart2 { /* console */
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart2>;
> > + status = "okay";
> > +};
> > +
> > +&uart3 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart3>;
> > + assigned-clocks = <&clk IMX8MM_CLK_UART3>;
> > + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> > + status = "okay";
> > +};
> > +
> > +&usdhc2 {
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
>
> As pinctrl_usdhc2_gpio is not going to change anyway in state of 100mhz
> and 200mhz, we do not need to put it in those state, right?
>
> > + bus-width = <4>;
> > + vmmc-supply = <®_usdhc2_vmmc>;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > +
>
> Drop the newline.
>
> > + pinctrl_i2c2: i2c2grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_i2c4: i2c4grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_espi2: espi2grp {
>
> Sort the pinctrl entries alphabetically.
>
> > + fsl,pins = <
> > + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82
> > + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82
> > + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82
> > + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41
> > + >;
> > + };
> > +
> > + pinctrl_led3: led3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x41
> > + >;
> > + };
> > +
> > + pinctrl_pcal6414: pcal6414-gpio {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19
> > + >;
> > + };
> > +
> > + pinctrl_sai3: sai3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
> > + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
> > + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6
> > + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
> > + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6
> > + >;
> > + };
> > +
> > + pinctrl_uart2: uart2grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> > + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> > + >;
> > + };
> > +
> > + pinctrl_uart3: uart3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x40
> > + MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x40
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x41
> > + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2: usdhc2grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> > + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> > + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
> > + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
> > + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
> > + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0
> > + >;
> > + };
> > +};
> > +
> > diff --git a/arch/arm64/boot/dts/freescale/beacon-imx8mm-kit.dts b/arch/arm64/boot/dts/freescale/beacon-imx8mm-kit.dts
> > new file mode 100644
> > index 000000000000..417b15d345d5
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/beacon-imx8mm-kit.dts
> > @@ -0,0 +1,19 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2020 Compass Electronics Group, LLC
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "imx8mm.dtsi"
> > +#include "beacon-imx8mm-som.dtsi"
> > +#include "beacon-imx8mm-baseboard.dtsi"
> > +
> > +/ {
> > + model = "Beacon EmbeddedWorks i.MX8M Mini Development Kit";
> > + compatible = "fsl,imx8mm";
> > +
> > + chosen {
> > + stdout-path = &uart2;
> > + };
> > +};
>
> Do we really need this level abstraction or we can just merge -baseboard
> and -kit?
On the surface, I see why you'd ask, but we want separate kit and
baseboard, because once the DSI video interface is working, we'll have
different variants for HDMI video and LVDS video using DSI bridge
chips. Since they will be mutually exclusive, they'll go at the kit
level and share the common baseboard items between them.
>
> > diff --git a/arch/arm64/boot/dts/freescale/beacon-imx8mm-som.dtsi b/arch/arm64/boot/dts/freescale/beacon-imx8mm-som.dtsi
> > new file mode 100644
> > index 000000000000..a2028322c2a3
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/beacon-imx8mm-som.dtsi
> > @@ -0,0 +1,411 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2020 Compass Electronics Group, LLC
> > + */
> > +
> > +/ {
> > + usdhc1_pwrseq: usdhc1_pwrseq {
> > + compatible = "mmc-pwrseq-simple";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1_gpio>;
> > + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
> > + clocks = <&osc_32k>;
> > + clock-names = "ext_clock";
> > + post-power-on-delay-ms = <80>;
> > + };
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + reg = <0x0 0x40000000 0 0x80000000>;
> > + };
> > +};
> > +
> > +&A53_0 {
> > + cpu-supply = <&buck2_reg>;
> > +};
> > +
> > +&ddrc {
> > + operating-points-v2 = <&ddrc_opp_table>;
> > +
> > + ddrc_opp_table: opp-table {
> > + compatible = "operating-points-v2";
> > +
> > + opp-25M {
> > + opp-hz = /bits/ 64 <25000000>;
> > + };
> > +
> > + opp-100M {
> > + opp-hz = /bits/ 64 <100000000>;
> > + };
> > +
> > + opp-750M {
> > + opp-hz = /bits/ 64 <750000000>;
> > + };
> > + };
> > +};
> > +
> > +&fec1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_fec1>;
> > + phy-mode = "rgmii-id";
> > + phy-handle = <ðphy0>;
> > + fsl,magic-packet;
> > + status = "okay";
> > +
> > + mdio {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + ethphy0: ethernet-phy@0 {
> > + compatible = "ethernet-phy-ieee802.3-c22";
> > + reg = <0>;
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c1>;
> > + status = "okay";
> > +
> > + pmic@4b {
> > + compatible = "rohm,bd71847";
> > + reg = <0x4b>;
> > + pinctrl-0 = <&pinctrl_pmic>;
> > + interrupt-parent = <&gpio1>;
> > + interrupts = <3 GPIO_ACTIVE_LOW>;
> > + rohm,reset-snvs-powered;
> > +
> > + regulators {
> > + buck1_reg: BUCK1 {
> > + regulator-name = "BUCK1";
> > + regulator-min-microvolt = <700000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <1250>;
> > + };
> > +
> > + buck2_reg: BUCK2 {
> > + regulator-name = "BUCK2";
> > + regulator-min-microvolt = <700000>;
> > + regulator-max-microvolt = <1300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + regulator-ramp-delay = <1250>;
> > + rohm,dvs-run-voltage = <1000000>;
> > + rohm,dvs-idle-voltage = <900000>;
> > + };
> > +
> > + buck3_reg: BUCK3 {
> > + // BUCK5 in datasheet
> > + regulator-name = "BUCK3";
> > + regulator-min-microvolt = <700000>;
> > + regulator-max-microvolt = <1350000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + buck4_reg: BUCK4 {
> > + // BUCK6 in datasheet
> > + regulator-name = "BUCK4";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + buck5_reg: BUCK5 {
> > + // BUCK7 in datasheet
> > + regulator-name = "BUCK5";
> > + regulator-min-microvolt = <1605000>;
> > + regulator-max-microvolt = <1995000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + buck6_reg: BUCK6 {
> > + // BUCK8 in datasheet
> > + regulator-name = "BUCK6";
> > + regulator-min-microvolt = <800000>;
> > + regulator-max-microvolt = <1400000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo1_reg: LDO1 {
> > + regulator-name = "LDO1";
> > + regulator-min-microvolt = <3000000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo2_reg: LDO2 {
> > + regulator-name = "LDO2";
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <900000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo3_reg: LDO3 {
> > + regulator-name = "LDO3";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo4_reg: LDO4 {
> > + regulator-name = "LDO4";
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > +
> > + ldo6_reg: LDO6 {
> > + regulator-name = "LDO6";
> > + regulator-min-microvolt = <900000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-boot-on;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c3 {
> > + clock-frequency = <400000>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_i2c3>;
> > + status = "okay";
> > +
> > + eeprom@50 {
> > + compatible = "atmel,24c64";
> > + pagesize = <32>;
> > + read-only; /* Manufacturing EEPROM programmed at factory */
> > + reg = <0x50>;
> > + };
> > +
> > + rtc@51 {
> > + compatible = "nxp,pcf85263";
> > + reg = <0x51>;
> > + };
> > +};
> > +
> > +&uart1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_uart1>;
> > + assigned-clocks = <&clk IMX8MM_CLK_UART1>;
> > + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> > + fsl,uart-has-rtscts;
>
> uart-has-rtscts
>
> Shawn
>
> > + status = "okay";
> > +
> > + bluetooth {
> > + compatible = "brcm,bcm43438-bt";
> > + shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
> > + host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
> > + device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
> > + clocks = <&osc_32k>;
> > + clock-names = "extclk";
> > + };
> > +};
> > +
> > +&usdhc1 {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_usdhc1>;
> > + bus-width = <4>;
> > + non-removable;
> > + cap-power-off-card;
> > + pm-ignore-notify;
> > + keep-power-in-suspend;
> > + mmc-pwrseq = <&usdhc1_pwrseq>;
> > + status = "okay";
> > +
> > + brcmf: bcrmf@1 {
> > + reg = <1>;
> > + compatible = "brcm,bcm4329-fmac";
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wlan>;
> > + interrupt-parent = <&gpio2>;
> > + interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-names = "host-wake";
> > + };
> > +};
> > +
> > +&usdhc3 {
> > + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> > + pinctrl-0 = <&pinctrl_usdhc3>;
> > + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> > + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> > + bus-width = <8>;
> > + non-removable;
> > + status = "okay";
> > +};
> > +
> > +&wdog1 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_wdog>;
> > + fsl,ext-reset-output;
> > + status = "okay";
> > +};
> > +
> > +&iomuxc {
> > +
> > + pinctrl_fec1: fec1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> > + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> > + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> > + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> > + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> > + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> > + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> > + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> > + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> > + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> > + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> > + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> > + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> > + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> > + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19
> > + >;
> > + };
> > +
> > + pinctrl_i2c1: i2c1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_i2c3: i2c3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> > + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> > + >;
> > + };
> > +
> > + pinctrl_pmic: pmicirq {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41
> > + >;
> > + };
> > +
> > + pinctrl_uart1: uart1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
> > + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
> > + MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
> > + MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
> > + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19
> > + MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7 0x19
> > + MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x19
> > + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_gpio: usdhc1grpgpio {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1: usdhc1grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
> > + >;
> > + };
> > +
> > + pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
> > + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
> > + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3: usdhc3grp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0
> > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0
> > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0
> > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0
> > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194
> > + >;
> > + };
> > +
> > + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> > + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> > + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> > + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6
> > + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6
> > + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6
> > + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6
> > + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196
> > + >;
> > + };
> > +
> > + pinctrl_wdog: wdoggrp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
> > + >;
> > + };
> > +
> > + pinctrl_wlan: wlangrp {
> > + fsl,pins = <
> > + MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x111
> > + >;
> > + };
> > +};
> > --
> > 2.25.0
> >
