Hi Alex,
(CC'ing Morimoto-san)
On Fri, Mar 06, 2020 at 02:41:54PM +0100, Alex Riesen wrote:
> Laurent Pinchart, Fri, Mar 06, 2020 14:16:32 +0100:
> > On Thu, Mar 05, 2020 at 03:36:28PM +0100, Alex Riesen wrote:
> >> Geert Uytterhoeven, Mon, Mar 02, 2020 17:13:30 +0100:
> >>> On Mon, Mar 2, 2020 at 5:09 PM Alex Riesen <alexander.riesen@xxxxxxxxxxx> wrote:
> >>>> Geert Uytterhoeven, Mon, Mar 02, 2020 16:32:32 +0100:
> >>>>>
> >>>>> The #clock-cells should be in the main video-receiver node.
> >>>>> Probably there is more than one clock output, so #clock-cells may be 1?
> >>>>
> >>>> AFAICS, the device can provide only this one clock line (audio master clock
> >>>> for I2S output)... I shall re-check, just in case.
> >>
> >> And you're right, of course: the audio output formatting module of the ADV748x
> >> devices provides a set of clock lines related to the I2S pins: the already
> >> discussed master clock, left-right channel clock and the serial clock (bit
> >> clock?).
> >
> > I don't think we need to model the last two clocks through CCF though,
> > they're part of the I2S protocol, not clock sources that need to be
> > explicitly controlled (or queried).
>
> That's good, because I'm right now having hard time finding out how to
> calculate the frequencies!
>
> >> Just to try it out (I'll set #clock-cells to 1), I registered a fixed rate
> >> clock in the driver, added a clock provider:
> >>
> >> adv748x_probe:
> >>
> >> clk = clk_register_fixed_rate(state->dev,
> >> "clk-hdmi-i2s-mclk",
> >> NULL /* parent_name */,
> >> 0 /* flags */,
> >> 12288000 /* rate */);
> >> of_clk_add_provider(state->dev->of_node, of_clk_src_simple_get, clk);
> >>
> >> And removed the audio_clk_c frequency setting. I also replaced the audio_clk_c
> >> in the list of input clocks of the R-Car-side sound card with the phandle of
> >> the adv7482 main node:
> >>
> >> salvator-common.dtsi:
> >>
> >> &i2c4 {
> >> status = "okay";
> >>
> >> adv7482_hdmi_decoder: video-receiver@70 {
> >> #clock-cells = <0>; // to be replaced with <1>
> >> };
> >> };
> >>
> >> &rcar_sound {
> >> clocks = ..., <&adv7482_hdmi_decoder>, ...;
> >> };
> >>
> >> As everything continues to work as before, I assume that at least the clock
> >> dependencies were resolved.
> >
> > This looks good to me.
>
> Ok, I settle on this than.
>
> >> Is there a way to verify that the added input clock is actually used?
> >> IOW, if its frequency is actually has been programmed into the ssi4 (R-Car
> >> receiving hardware) registers, and not just a left-over from previuos attempts
> >> or plain default setting?
> >>
> >> As the ADV748x devices seem to provide also the clocks for video outputs, will
> >> it make any sense to place the clock definition into the port node?
> >> Or should all provided clocks be indexed in the main device node?
> >
> > Those clocks are part of the CSI-2 protocol and also don't need to be
> > explicitly controlled. As far as I can tell from a quick check of the
> > ADV7482 documentation, only the I2S MCLK is a general-purpose clock that
> > needs to be exposed.
>
> Thanks, that's good to know!
>
> Do you know, by chance, which of the snd_soc* callbacks should be used to
> implement setting of the MCLK? The one in snd_soc_component_driver or
> snd_soc_dai_driver->ops (snd_soc_dai_ops)?
>
> Or how the userspace interface looks like? Or, if there is no userspace
> interface for this, how the MCLK is supposed to be set? Through mclk-fs?
I'm afraid my knowledge of the sound subsystem is limited. Morimoto-san
is the main developer and maintainer of Renesas sound drivers.
Morimoto-sensei, would you have an answer to that question ? :-)
--
Regards,
Laurent Pinchart
