Convert the usb-connector.txt bindings file to YAML format. This allows it to be used in dt_bindings_check verification. This patch was born out of a patch series for the addition of a Type C connector class port driver[1]. An attempt has been made to maintain the same documentation text and example structure as was in the .txt file, but wherever needed modifications have been made to satisfy dt_bindings_check. Also, update all references to usb-connector.txt to now use usb-connector.yaml. [1]: https://lkml.org/lkml/2020/2/19/1232 Signed-off-by: Prashant Malani <pmalani@xxxxxxxxxxxx> --- .../connector/samsung,usb-connector-11pin.txt | 2 +- .../bindings/connector/usb-connector.txt | 135 ------------ .../bindings/connector/usb-connector.yaml | 193 ++++++++++++++++++ .../devicetree/bindings/usb/fcs,fusb302.txt | 2 +- .../devicetree/bindings/usb/generic.txt | 2 +- .../devicetree/bindings/usb/mediatek,mtu3.txt | 2 +- .../devicetree/bindings/usb/mediatek,musb.txt | 2 +- .../bindings/usb/richtek,rt1711h.txt | 2 +- .../devicetree/bindings/usb/ti,hd3ss3220.txt | 2 +- .../devicetree/bindings/usb/typec-tcpci.txt | 2 +- .../devicetree/bindings/usb/usb-conn-gpio.txt | 4 +- 11 files changed, 203 insertions(+), 145 deletions(-) delete mode 100644 Documentation/devicetree/bindings/connector/usb-connector.txt create mode 100644 Documentation/devicetree/bindings/connector/usb-connector.yaml diff --git a/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt index 22256e295a7a1..3dd8961154abf 100644 --- a/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt +++ b/Documentation/devicetree/bindings/connector/samsung,usb-connector-11pin.txt @@ -19,7 +19,7 @@ Required nodes: 0: High Speed (HS), 3: Mobile High-Definition Link (MHL), specific to 11-pin Samsung micro-USB. -[1]: bindings/connector/usb-connector.txt +[1]: bindings/connector/usb-connector.yaml Example ------- diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt deleted file mode 100644 index 88578ac1a8a76..0000000000000 --- a/Documentation/devicetree/bindings/connector/usb-connector.txt +++ /dev/null @@ -1,135 +0,0 @@ -USB Connector -============= - -A USB connector node represents a physical USB connector. It should be -a child of a USB interface controller. - -Required properties: -- compatible: describes type of the connector, must be one of: - "usb-a-connector", - "usb-b-connector", - "usb-c-connector". - -Optional properties: -- label: symbolic name for the connector, -- type: size of the connector, should be specified in case of USB-A, USB-B - non-fullsize connectors: "mini", "micro". -- self-powered: Set this property if the usb device that has its own power - source. - -Optional properties for usb-b-connector: -- id-gpios: an input gpio for USB ID pin. -- vbus-gpios: an input gpio for USB VBUS pin, used to detect presence of - VBUS 5V. - see gpio/gpio.txt. -- vbus-supply: a phandle to the regulator for USB VBUS if needed when host - mode or dual role mode is supported. - Particularly, if use an output GPIO to control a VBUS regulator, should - model it as a regulator. - see regulator/fixed-regulator.yaml -- pinctrl-names : a pinctrl state named "default" is optional -- pinctrl-0 : pin control group - see pinctrl/pinctrl-bindings.txt - -Optional properties for usb-c-connector: -- power-role: should be one of "source", "sink" or "dual"(DRP) if typec - connector has power support. -- try-power-role: preferred power role if "dual"(DRP) can support Try.SNK - or Try.SRC, should be "sink" for Try.SNK or "source" for Try.SRC. -- data-role: should be one of "host", "device", "dual"(DRD) if typec - connector supports USB data. - -Required properties for usb-c-connector with power delivery support: -- source-pdos: An array of u32 with each entry providing supported power - source data object(PDO), the detailed bit definitions of PDO can be found - in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 - Source_Capabilities Message, the order of each entry(PDO) should follow - the PD spec chapter 6.4.1. Required for power source and power dual role. - User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() - defined in dt-bindings/usb/pd.h. -- sink-pdos: An array of u32 with each entry providing supported power - sink data object(PDO), the detailed bit definitions of PDO can be found - in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 - Sink Capabilities Message, the order of each entry(PDO) should follow - the PD spec chapter 6.4.1. Required for power sink and power dual role. - User can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined - in dt-bindings/usb/pd.h. -- op-sink-microwatt: Sink required operating power in microwatt, if source - can't offer the power, Capability Mismatch is set. Required for power - sink and power dual role. - -Required nodes: -- any data bus to the connector should be modeled using the OF graph bindings - specified in bindings/graph.txt, unless the bus is between parent node and - the connector. Since single connector can have multiple data buses every bus - has assigned OF graph port number as follows: - 0: High Speed (HS), present in all connectors, - 1: Super Speed (SS), present in SS capable connectors, - 2: Sideband use (SBU), present in USB-C. - -Examples --------- - -1. Micro-USB connector with HS lines routed via controller (MUIC): - -muic-max77843@66 { - ... - usb_con: connector { - compatible = "usb-b-connector"; - label = "micro-USB"; - type = "micro"; - }; -}; - -2. USB-C connector attached to CC controller (s2mm005), HS lines routed -to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. -DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. - -ccic: s2mm005@33 { - ... - usb_con: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - usb_con_hs: endpoint { - remote-endpoint = <&max77865_usbc_hs>; - }; - }; - port@1 { - reg = <1>; - usb_con_ss: endpoint { - remote-endpoint = <&usbdrd_phy_ss>; - }; - }; - port@2 { - reg = <2>; - usb_con_sbu: endpoint { - remote-endpoint = <&dp_aux>; - }; - }; - }; - }; -}; - -3. USB-C connector attached to a typec port controller(ptn5110), which has -power delivery support and enables drp. - -typec: ptn5110@50 { - ... - usb_con: connector { - compatible = "usb-c-connector"; - label = "USB-C"; - power-role = "dual"; - try-power-role = "sink"; - source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; - sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) - PDO_VAR(5000, 12000, 2000)>; - op-sink-microwatt = <10000000>; - }; -}; diff --git a/Documentation/devicetree/bindings/connector/usb-connector.yaml b/Documentation/devicetree/bindings/connector/usb-connector.yaml new file mode 100644 index 0000000000000..f0fac9bd63364 --- /dev/null +++ b/Documentation/devicetree/bindings/connector/usb-connector.yaml @@ -0,0 +1,193 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/connector/usb-connector.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB Connector + +maintainers: + - linux-usb@xxxxxxxxxxxxxxx + +description: + A USB connector node represents a physical USB connector. It should be a child + of a USB interface controller. + +properties: + compatible: + enum: + - usb-a-connector + - usb-b-connector + - usb-c-connector + + label: + description: Symbolic name for the connector. + + type: + description: Size of the connector, should be specified in case of USB-A, + USB-B non-fullsize connectors. + enum: + - mini + - micro + + self-powered: + description: Set this property if the USB device has its own power source. + + # The following are optional properties for "usb-b-connector". + id-gpios: + description: An input gpio for USB ID pin. + + vbus-gpios: + description: An input gpio for USB VBus pin, used to detect presence of + VBUS 5V. See gpio/gpio.txt. + + vbus-supply: + description: A phandle to the regulator for USB VBUS if needed when host + mode or dual role mode is supported. + Particularly, if use an output GPIO to control a VBUS regulator, should + model it as a regulator. See regulator/fixed-regulator.yaml + + pinctrl-names: + description: A pinctrl state named "default" is optional. + + pinctrl-0: + description: Pin control group. See pinctrl/pinctrl-bindings.txt + + # The following are optional properties for "usb-c-connector". + power-role: + description: Determines the power role that the Type C connector will + support. + contains: + source: + description: Connector is a power source. + sink: + description: Connector is a power sink. + dual: + description: Connector is a Dual Role Port (DRP). + + try-power-role: + description: Preferred power role. + contains: + sink: + description: Try.SNK is preferred power role. + source: + description: Try.SRC is preferred power role. + dual: + description: DRP can support Try.SNK or Try.SRC. + + data-role: + description: Data role if Type C connector supports USB data. + contains: + host: + description: Connector is a host. + device: + description: Connector is a device. + dual: + description: Connector is Dual Role Device (DRD). + + # The following are optional properties for "usb-c-connector" with power + # delivery support. + source-pdos: + description: An array of u32 with each entry providing supported power + source data object(PDO), the detailed bit definitions of PDO can be found + in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 + Source_Capabilities Message, the order of each entry(PDO) should follow + the PD spec chapter 6.4.1. Required for power source and power dual role. + User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() + defined in dt-bindings/usb/pd.h. + minItems: 1 + maxItems: 7 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + + + sink-pdos: + description: An array of u32 with each entry providing supported power sink + data object(PDO), the detailed bit definitions of PDO can be found in + "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 + Sink Capabilities Message, the order of each entry(PDO) should follow the + PD spec chapter 6.4.1. Required for power sink and power dual role. User + can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined + in dt-bindings/usb/pd.h. + minItems: 1 + maxItems: 7 + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + + op-sink-microwatt: + description: Sink required operating power in microwatt, if source can't + offer the power, Capability Mismatch is set. Required for power sink and + power dual role. + +# Any data bus to the connector should be modeled using the OF graph bindings +# specified in bindings/graph.txt, unless the bus is between parent node and +# the connector. Since single connector can have multiple data buses every bus +# has assigned OF graph port number as follows: +# 0: High Speed (HS), present in all connectors, +# 1: Super Speed (SS), present in SS capable connectors, +# 2: Sideband use (SBU), present in USB-C. +required: + - compatible + +examples: + # Micro-USB connector with HS lines routed via controller (MUIC). + - |+ + muic-max77843@66 { + usb_con1: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; + }; + + # USB-C connector attached to CC controller (s2mm005), HS lines routed + # to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. + # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. + - |+ + ccic: s2mm005@33 { + usb_con2: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + usb_con_hs: endpoint { + remote-endpoint = <&max77865_usbc_hs>; + }; + }; + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usbdrd_phy_ss>; + }; + }; + port@2 { + reg = <2>; + usb_con_sbu: endpoint { + remote-endpoint = <&dp_aux>; + }; + }; + }; + }; + }; + + # USB-C connector attached to a typec port controller(ptn5110), which has + # power delivery support and enables drp. + - |+ + #include <dt-bindings/usb/pd.h> + typec: ptn5110@50 { + usb_con3: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index ba2e32d500c02..60e4654297af7 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -9,7 +9,7 @@ Required sub-node: - connector : The "usb-c-connector" attached to the FUSB302 IC. The bindings of the connector node are specified in: - Documentation/devicetree/bindings/connector/usb-connector.txt + Documentation/devicetree/bindings/connector/usb-connector.yaml Example: diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index e6790d2a4da9b..474e74c06522d 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -34,7 +34,7 @@ Optional properties: - usb-role-switch: boolean, indicates that the device is capable of assigning the USB data role (USB host or USB device) for a given USB connector, such as Type-C, Type-B(micro). - see connector/usb-connector.txt. + see connector/usb-connector.yaml. This is an attribute to a USB controller such as: diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt index e0ae6096f7ac8..a82ca438aec1f 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -34,7 +34,7 @@ Optional properties: dual-role mode. it's considered valid for compatibility reasons, not allowed for new bindings, and put into a usb-connector node. - see connector/usb-connector.txt. + see connector/usb-connector.yaml. - pinctrl-names : a pinctrl state named "default" is optional, and need be defined if auto drd switch is enabled, that means the property dr_mode is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt index 2b8a87c90d9ea..5eedb02965622 100644 --- a/Documentation/devicetree/bindings/usb/mediatek,musb.txt +++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt @@ -23,7 +23,7 @@ Optional properties: MTCMOS Required child nodes: - usb connector node as defined in bindings/connector/usb-connector.txt + usb connector node as defined in bindings/connector/usb-connector.yaml Optional properties: - id-gpios : input GPIO for USB ID pin. - vbus-gpios : input GPIO for USB VBUS pin. diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt index e3fc57e605ed6..6f8115db2ea9b 100644 --- a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -9,7 +9,7 @@ Required properties: Required sub-node: - connector: The "usb-c-connector" attached to the tcpci chip, the bindings of connector node are specified in - Documentation/devicetree/bindings/connector/usb-connector.txt + Documentation/devicetree/bindings/connector/usb-connector.yaml Example : rt1711h@4e { diff --git a/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt b/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt index 25780e945b154..2bd21b22ce95b 100644 --- a/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt +++ b/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt @@ -9,7 +9,7 @@ Required sub-node: - connector: The "usb-c-connector" attached to the hd3ss3220 chip. The bindings of the connector node are specified in: - Documentation/devicetree/bindings/connector/usb-connector.txt + Documentation/devicetree/bindings/connector/usb-connector.yaml Example: hd3ss3220@47 { diff --git a/Documentation/devicetree/bindings/usb/typec-tcpci.txt b/Documentation/devicetree/bindings/usb/typec-tcpci.txt index 0dd1469e73180..2082522b1c326 100644 --- a/Documentation/devicetree/bindings/usb/typec-tcpci.txt +++ b/Documentation/devicetree/bindings/usb/typec-tcpci.txt @@ -13,7 +13,7 @@ Required properties: Required sub-node: - connector: The "usb-c-connector" attached to the tcpci chip, the bindings of connector node are specified in - Documentation/devicetree/bindings/connector/usb-connector.txt + Documentation/devicetree/bindings/connector/usb-connector.yaml Example: diff --git a/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt b/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt index 3d05ae56cb0dc..ec80641208a53 100644 --- a/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt +++ b/Documentation/devicetree/bindings/usb/usb-conn-gpio.txt @@ -8,11 +8,11 @@ Required properties: - compatible : should include "gpio-usb-b-connector" and "usb-b-connector". - id-gpios, vbus-gpios : input gpios, either one of them must be present, and both can be present as well. - see connector/usb-connector.txt + see connector/usb-connector.yaml Optional properties: - vbus-supply : can be present if needed when supports dual role mode. - see connector/usb-connector.txt + see connector/usb-connector.yaml - Sub-nodes: - port : can be present. -- 2.25.0.265.gbab2e86ba0-goog
