On Mon, Mar 02, 2020 at 04:34:40PM +0000, Ajay.Kathat@xxxxxxxxxxxxx wrote: > From: Ajay Singh <ajay.kathat@xxxxxxxxxxxxx> > > Moved '/drivers/staging/wilc1000/microchip,wilc1000,sdio.yaml' to > 'Documentation/devicetree/bindings/net/wireless/microchip,wilc1000,sdio.yaml'. > > Signed-off-by: Ajay Singh <ajay.kathat@xxxxxxxxxxxxx> > --- > .../net/wireless/microchip,wilc1000,sdio.yaml | 68 +++++++++++++++++++ > 1 file changed, 68 insertions(+) > create mode 100644 Documentation/devicetree/bindings/net/wireless/microchip,wilc1000,sdio.yaml > > diff --git a/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000,sdio.yaml b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000,sdio.yaml > new file mode 100644 > index 000000000000..b338f569f7e2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/wireless/microchip,wilc1000,sdio.yaml > @@ -0,0 +1,68 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000,sdio.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Microchip WILC wireless SDIO devicetree bindings > + > +maintainers: > + - Adham Abozaeid <adham.abozaeid@xxxxxxxxxxxxx> > + - Ajay Singh <ajay.kathat@xxxxxxxxxxxxx> > + > +description: > + The wilc1000 chips can be connected via SDIO. The node is used to > + specify child node to the SDIO controller that connects the device > + to the system. > + > +properties: > + compatible: > + const: microchip,wilc1000-sdio > + > + irq-gpios: Unless you need GPIO control of the line, use 'interrupts' instead. > + description: The GPIO phandle connect to a host IRQ. > + maxItems: 1 > + > + reg: > + description: Slot ID used in the controller. No, it's the function number. But you can just drop this. > + maxItems: 1 > + > + clocks: > + description: phandle to the clock connected on rtc clock line. > + maxItems: 1 > + > + bus-width: I believe this is defined to go in the parent node. > + description: The number of data lines wired up the slot. > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - enum: [1, 4, 8] > + - default: 1 > + > +required: > + - compatible > + - irq-gpios > + - reg > + > +examples: > + - | > + mmc1: mmc@fc000000 { > + #address-cells = <1>; > + #size-cells = <0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>; > + non-removable; > + vmmc-supply = <&vcc_mmc1_reg>; > + vqmmc-supply = <&vcc_3v3_reg>; > + status = "okay"; Don't show 'status' in examples. > + wilc_sdio@0 { wifi@0 > + compatible = "microchip,wilc1000-sdio"; > + irq-gpios = <&pioC 27 0>; > + reg = <0>; > + clocks = <&pck1>; > + clock-names = "rtc_clk"; > + assigned-clocks = <&pck1>; > + assigned-clock-rates = <32768>; > + status = "okay"; > + bus-width = <4>; > + }; > + }; > -- > 2.24.0
