[PATCH v4 9/9] power: supply: Support ROHM bd99954 charger

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.

Support ROHM BD99954 Charger IC.

Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
---

no changes since rfc-v3

 drivers/power/supply/Kconfig           |   10 +
 drivers/power/supply/Makefile          |    1 +
 drivers/power/supply/bd99954-charger.c | 1171 ++++++++++++++++++++++++
 include/linux/power/bd99954-charger.h  | 1075 ++++++++++++++++++++++
 4 files changed, 2257 insertions(+)
 create mode 100644 drivers/power/supply/bd99954-charger.c
 create mode 100644 include/linux/power/bd99954-charger.h

diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 8781c674ed07..0b3bad6fc736 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -702,6 +702,16 @@ config CHARGER_BD70528
 	 information and altering charger configurations from charger
 	 block of the ROHM BD70528 Power Management IC.
 
+config CHARGER_BD99954
+	tristate "ROHM bd99954 charger driver"
+	depends on I2C
+	select LINEAR_RANGES
+	default n
+	help
+	 Say Y here to enable support for getting battery and charger
+	 information and altering charger configurations from the ROHM
+	 BD99954 charger IC.
+
 config CHARGER_WILCO
 	tristate "Wilco EC based charger for ChromeOS"
 	depends on WILCO_EC
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 6c7da920ea83..eed11ca1bd7d 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -91,4 +91,5 @@ obj-$(CONFIG_CHARGER_SC2731)	+= sc2731_charger.o
 obj-$(CONFIG_FUEL_GAUGE_SC27XX)	+= sc27xx_fuel_gauge.o
 obj-$(CONFIG_CHARGER_UCS1002)	+= ucs1002_power.o
 obj-$(CONFIG_CHARGER_BD70528)	+= bd70528-charger.o
+obj-$(CONFIG_CHARGER_BD99954)	+= bd99954-charger.o
 obj-$(CONFIG_CHARGER_WILCO)	+= wilco-charger.o
diff --git a/drivers/power/supply/bd99954-charger.c b/drivers/power/supply/bd99954-charger.c
new file mode 100644
index 000000000000..abcf47194e34
--- /dev/null
+++ b/drivers/power/supply/bd99954-charger.c
@@ -0,0 +1,1171 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * ROHM BD99954 charger driver
+ *
+ * Copyright (C) 2020 Rohm Semiconductors
+ *	Originally written by:
+ *		Mikko Mutanen <mikko.mutanen@xxxxxxxxxxxxxxxxx>
+ *		Markus Laine <markus.laine@xxxxxxxxxxxxxxxxx>
+ *	Bugs added by:
+ *		Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
+ */
+
+/*
+ *   The battery charging profile of BD99954.
+ *
+ *   Curve (1) represents charging current.
+ *   Curve (2) represents battery voltage.
+ *
+ *   The BD99954 data sheet divides charging to three phases.
+ *   a) Trickle-charge with constant current (8).
+ *   b) pre-charge with constant current (6)
+ *   c) fast-charge, first with constant current (5) phase. After
+ *      the battery voltage has reached target level (4) we have constant
+ *      voltage phase until charging current has dropped to termination
+ *      level (7)
+ *
+ *    V ^                                                        ^ I
+ *      .                                                        .
+ *      .                                                        .
+ *(4)` `.` ` ` ` ` ` ` ` ` ` ` ` ` ` ----------------------------.
+ *      .                           :/                           .
+ *      .                     o----+/:/ ` ` ` ` ` ` ` ` ` ` ` ` `.` ` (5)
+ *      .                     +   ::  +                          .
+ *      .                     +  /-   --                         .
+ *      .                     +`/-     +                         .
+ *      .                     o/-      -:                        .
+ *      .                    .s.        +`                       .
+ *      .                  .--+         `/                       .
+ *      .               ..``  +          .:                      .
+ *      .             -`      +           --                     .
+ *      .    (2)  ...``       +            :-                    .
+ *      .    ...``            +             -:                   .
+ *(3)` `.`.""  ` ` ` `+-------- ` ` ` ` ` ` `.:` ` ` ` ` ` ` ` ` .` ` (6)
+ *      .             +                       `:.                .
+ *      .             +                         -:               .
+ *      .             +                           -:.            .
+ *      .             +                             .--.         .
+ *      .   (1)       +                                `.+` ` ` `.` ` (7)
+ *      -..............` ` ` ` ` ` ` ` ` ` ` ` ` ` ` ` ` + ` ` ` .` ` (8)
+ *      .                                                +       -
+ *      -------------------------------------------------+++++++++-->
+ *      |   trickle   |  pre  |          fast            |
+ *
+ * Details of DT properties for different limits can be found from BD99954
+ * device tree binding documentation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/linear_range.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/power/bd99954-charger.h>
+#include <linux/power_supply.h>
+#include <linux/regmap.h>
+#include <linux/types.h>
+
+struct battery_data {
+	u16 precharge_current;	/* Trickle-charge Current */
+	u16 fc_reg_voltage;	/* Fast Charging Regulation Voltage */
+	u16 voltage_min;
+	u16 voltage_max;
+};
+
+/* initial field values, converted to initial register values */
+struct bd9995x_init_data {
+	u16 vsysreg_set;	/* VSYS Regulation Setting */
+	u16 ibus_lim_set;	/* VBUS input current limitation */
+	u16 icc_lim_set;	/* VCC/VACP Input Current Limit Setting */
+	u16 itrich_set;		/* Trickle-charge Current Setting */
+	u16 iprech_set;		/* Pre-Charge Current Setting */
+	u16 ichg_set;		/* Fast-Charge constant current */
+	u16 vfastchg_reg_set1;	/* Fast Charging Regulation Voltage */
+	u16 vprechg_th_set;	/* Pre-charge Voltage Threshold Setting */
+	u16 vrechg_set;		/* Re-charge Battery Voltage Setting */
+	u16 vbatovp_set;	/* Battery Over Voltage Threshold Setting */
+	u16 iterm_set;		/* Charging termination current */
+};
+
+struct bd9995x_state {
+	u8 online;
+	u16 chgstm_status;
+	u16 vbat_vsys_status;
+	u16 vbus_vcc_status;
+};
+
+struct bd9995x_device {
+	struct i2c_client *client;
+	struct device *dev;
+	struct power_supply *charger;
+
+	struct regmap *rmap;
+	struct regmap_field *rmap_fields[F_MAX_FIELDS];
+
+	int chip_id;
+	int chip_rev;
+	struct bd9995x_init_data init_data;
+	struct bd9995x_state state;
+
+	struct mutex lock; /* protect state data */
+};
+
+static const struct regmap_range bd9995x_readonly_reg_ranges[] = {
+	regmap_reg_range(CHGSTM_STATUS, SEL_ILIM_VAL),
+	regmap_reg_range(IOUT_DACIN_VAL, IOUT_DACIN_VAL),
+	regmap_reg_range(VCC_UCD_STATUS, VCC_IDD_STATUS),
+	regmap_reg_range(VBUS_UCD_STATUS, VBUS_IDD_STATUS),
+	regmap_reg_range(CHIP_ID, CHIP_REV),
+	regmap_reg_range(SYSTEM_STATUS, SYSTEM_STATUS),
+	regmap_reg_range(IBATP_VAL, VBAT_AVE_VAL),
+	regmap_reg_range(VTH_VAL, EXTIADP_AVE_VAL),
+};
+
+static const struct regmap_access_table bd9995x_writeable_regs = {
+	.no_ranges = bd9995x_readonly_reg_ranges,
+	.n_no_ranges = ARRAY_SIZE(bd9995x_readonly_reg_ranges),
+};
+
+static const struct regmap_range bd9995x_volatile_reg_ranges[] = {
+	regmap_reg_range(CHGSTM_STATUS, WDT_STATUS),
+	regmap_reg_range(VCC_UCD_STATUS, VCC_IDD_STATUS),
+	regmap_reg_range(VBUS_UCD_STATUS, VBUS_IDD_STATUS),
+	regmap_reg_range(INT0_STATUS, INT7_STATUS),
+	regmap_reg_range(SYSTEM_STATUS, SYSTEM_CTRL_SET),
+	regmap_reg_range(IBATP_VAL, EXTIADP_AVE_VAL), /* measurement regs */
+};
+
+static const struct regmap_access_table bd9995x_volatile_regs = {
+	.yes_ranges = bd9995x_volatile_reg_ranges,
+	.n_yes_ranges = ARRAY_SIZE(bd9995x_volatile_reg_ranges),
+};
+
+static const struct regmap_range_cfg regmap_range_cfg[] = {
+	{
+	.selector_reg     = MAP_SET,
+	.selector_mask    = 0xFFFF,
+	.selector_shift   = 0,
+	.window_start     = 0,
+	.window_len       = 0x100,
+	.range_min        = 0 * 0x100,
+	.range_max        = 3 * 0x100,
+	},
+};
+
+static const struct regmap_config bd9995x_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 16,
+	.reg_stride = 1,
+
+	.max_register = 3*0x100,
+	.cache_type = REGCACHE_RBTREE,
+
+	.ranges = regmap_range_cfg,
+	.num_ranges = ARRAY_SIZE(regmap_range_cfg),
+	.val_format_endian = REGMAP_ENDIAN_LITTLE,
+	.wr_table = &bd9995x_writeable_regs,
+	.volatile_table = &bd9995x_volatile_regs,
+};
+
+#define IDI0T_BIT 0x1
+
+enum bd9995x_chrg_fault {
+	CHRG_FAULT_NORMAL,
+	CHRG_FAULT_INPUT,
+	CHRG_FAULT_THERMAL_SHUTDOWN,
+	CHRG_FAULT_TIMER_EXPIRED,
+};
+
+static int bd9995x_get_prop_batt_health(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_BATTEMP], &tmp);
+	if (ret)
+		return POWER_SUPPLY_HEALTH_UNKNOWN;
+
+	/* TODO: Check these against datasheet page 34 */
+
+	switch (tmp) {
+	case ROOM:
+		return POWER_SUPPLY_HEALTH_GOOD;
+	case HOT1:
+	case HOT2:
+	case HOT3:
+		return POWER_SUPPLY_HEALTH_OVERHEAT;
+	case COLD1:
+	case COLD2:
+		return POWER_SUPPLY_HEALTH_COLD;
+	case TEMP_DIS:
+	case BATT_OPEN:
+	default:
+		return POWER_SUPPLY_HEALTH_UNKNOWN;
+	}
+}
+
+static int bd9995x_get_prop_charge_type(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_CHGSTM_STATE], &tmp);
+	if (ret)
+		return POWER_SUPPLY_CHARGE_TYPE_UNKNOWN;
+
+	switch (tmp) {
+	case CHGSTM_TRICKLE_CHARGE:
+	case CHGSTM_PRE_CHARGE:
+		return POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
+	case CHGSTM_FAST_CHARGE:
+		return POWER_SUPPLY_CHARGE_TYPE_FAST;
+	case CHGSTM_TOP_OFF:
+	case CHGSTM_DONE:
+	case CHGSTM_SUSPEND:
+		return POWER_SUPPLY_CHARGE_TYPE_NONE;
+	default: /* rest of the states are error related, no charging */
+		return POWER_SUPPLY_CHARGE_TYPE_NONE;
+	}
+}
+
+static int bd9995x_get_prop_batt_present(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_BATTEMP], &tmp);
+	if (ret)
+		return false;
+
+	return (tmp != BATT_OPEN) ? true : false;
+}
+
+static int bd9995x_get_prop_batt_voltage(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_VBAT_VAL], &tmp);
+	if (ret)
+		return 0;
+
+	tmp = min(tmp, 19200);
+
+	return tmp * 1000;
+}
+
+static int bd9995x_get_prop_batt_current(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_IBATP_VAL], &tmp);
+	if (ret)
+		return 0;
+
+	return tmp * 1000;
+}
+
+#define DEFAULT_BATTERY_TEMPERATURE 250
+
+static int bd9995x_get_prop_batt_temp(struct bd9995x_device *bd)
+{
+	int ret, tmp;
+
+	ret = regmap_field_read(bd->rmap_fields[F_THERM_VAL], &tmp);
+	if (ret)
+		return DEFAULT_BATTERY_TEMPERATURE;
+
+	return (200 - tmp) * 10;
+}
+
+static int bd9995x_power_supply_get_property(struct power_supply *psy,
+					     enum power_supply_property psp,
+					     union power_supply_propval *val)
+{
+	int ret, tmp;
+	struct bd9995x_device *bd = power_supply_get_drvdata(psy);
+	struct bd9995x_state state;
+
+	mutex_lock(&bd->lock);
+	state = bd->state;
+	mutex_unlock(&bd->lock);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		switch (state.chgstm_status) {
+		case CHGSTM_TRICKLE_CHARGE:
+		case CHGSTM_PRE_CHARGE:
+		case CHGSTM_FAST_CHARGE:
+		case CHGSTM_TOP_OFF:
+			val->intval = POWER_SUPPLY_STATUS_CHARGING;
+			break;
+
+		case CHGSTM_DONE:
+			val->intval = POWER_SUPPLY_STATUS_FULL;
+			break;
+
+		case CHGSTM_SUSPEND:
+		case CHGSTM_TEMPERATURE_ERROR_1:
+		case CHGSTM_TEMPERATURE_ERROR_2:
+		case CHGSTM_TEMPERATURE_ERROR_3:
+		case CHGSTM_TEMPERATURE_ERROR_4:
+		case CHGSTM_TEMPERATURE_ERROR_5:
+		case CHGSTM_TEMPERATURE_ERROR_6:
+		case CHGSTM_TEMPERATURE_ERROR_7:
+		case CHGSTM_THERMAL_SHUT_DOWN_1:
+		case CHGSTM_THERMAL_SHUT_DOWN_2:
+		case CHGSTM_THERMAL_SHUT_DOWN_3:
+		case CHGSTM_THERMAL_SHUT_DOWN_4:
+		case CHGSTM_THERMAL_SHUT_DOWN_5:
+		case CHGSTM_THERMAL_SHUT_DOWN_6:
+		case CHGSTM_THERMAL_SHUT_DOWN_7:
+		case CHGSTM_BATTERY_ERROR:
+			val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING;
+			break;
+
+		default:
+			val->intval = POWER_SUPPLY_STATUS_UNKNOWN;
+			break;
+		}
+		break;
+
+	case POWER_SUPPLY_PROP_MANUFACTURER:
+		val->strval = BD9995X_MANUFACTURER;
+		break;
+
+	case POWER_SUPPLY_PROP_ONLINE:
+		val->intval = state.online;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT:
+		ret = regmap_field_read(bd->rmap_fields[F_IBATP_VAL], &tmp);
+		if (ret)
+			return ret;
+		val->intval = tmp * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CHARGE_AVG:
+		ret = regmap_field_read(bd->rmap_fields[F_IBATP_AVE_VAL], &tmp);
+		if (ret)
+			return ret;
+		val->intval = tmp * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX:
+		/*
+		 * Currently the DT uses this property to give the
+		 * target current for fast-charging constant current phase.
+		 * I think it is correct in a sense.
+		 *
+		 * Yet, this prop we read and return here is the programmed
+		 * safety limit for combined input currents. This feels
+		 * also correct in a sense.
+		 *
+		 * However, this results a mismatch to DT value and value
+		 * read from sysfs.
+		 */
+		ret = regmap_field_read(bd->rmap_fields[F_SEL_ILIM_VAL], &tmp);
+		if (ret)
+			return ret;
+		val->intval = tmp * 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE:
+		if (!state.online) {
+			val->intval = 0;
+			break;
+		}
+
+		ret = regmap_field_read(bd->rmap_fields[F_VFASTCHG_REG_SET1],
+					&tmp);
+		if (ret)
+			return ret;
+
+		val->intval = tmp << 4;
+		/*
+		 * the actual range : 2560 to 19200 mV. No matter what the
+		 * register says
+		 */
+		val->intval = max(val->intval, 2560);
+		val->intval = min(val->intval, 19200);
+		val->intval *= 1000;
+		break;
+
+	case POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT:
+		ret = regmap_field_read(bd->rmap_fields[F_ITERM_SET], &tmp);
+		if (ret)
+			return ret;
+		/* Start step is 64 mA */
+		val->intval = tmp << 6;
+		/* Maximum is 1024 mA - no matter what register says */
+		val->intval = min(val->intval, 1024);
+		val->intval *= 1000;
+		break;
+
+	/* Battery properties which we access through charger */
+	case POWER_SUPPLY_PROP_PRESENT:
+		val->intval = bd9995x_get_prop_batt_present(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		val->intval = bd9995x_get_prop_batt_voltage(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		val->intval = bd9995x_get_prop_batt_current(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_CHARGE_TYPE:
+		val->intval = bd9995x_get_prop_charge_type(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_HEALTH:
+		val->intval = bd9995x_get_prop_batt_health(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_TEMP:
+		val->intval = bd9995x_get_prop_batt_temp(bd);
+		break;
+
+	case POWER_SUPPLY_PROP_TECHNOLOGY:
+		val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
+		break;
+
+	case POWER_SUPPLY_PROP_MODEL_NAME:
+		val->strval = "bd99954";
+		break;
+
+	default:
+		return -EINVAL;
+
+	}
+
+	return 0;
+}
+
+static int bd9995x_get_chip_state(struct bd9995x_device *bd,
+				  struct bd9995x_state *state)
+{
+	int i, ret, tmp;
+	struct {
+		struct regmap_field *id;
+		u16 *data;
+	} state_fields[] = {
+		{
+			bd->rmap_fields[F_CHGSTM_STATE], &state->chgstm_status,
+		}, {
+			bd->rmap_fields[F_VBAT_VSYS_STATUS],
+			&state->vbat_vsys_status,
+		}, {
+			bd->rmap_fields[F_VBUS_VCC_STATUS],
+			&state->vbus_vcc_status,
+		},
+	};
+
+
+	for (i = 0; i < ARRAY_SIZE(state_fields); i++) {
+		ret = regmap_field_read(state_fields[i].id, &tmp);
+		if (ret)
+			return ret;
+
+		*state_fields[i].data = tmp;
+	}
+
+	if (state->vbus_vcc_status & STATUS_VCC_DET ||
+	    state->vbus_vcc_status & STATUS_VBUS_DET)
+		state->online = 1;
+	else
+		state->online = 0;
+
+	return 0;
+}
+
+static irqreturn_t bd9995x_irq_handler_thread(int irq, void *private)
+{
+	struct bd9995x_device *bd = private;
+	int ret, status, tmp, mask, i;
+	struct bd9995x_state state;
+
+	/*
+	 * The bd9995x does not seem to generate big amount of interrupts.
+	 * The logic regarding which interrupts can cause relevant
+	 * status changes seem to be pretty complex.
+	 *
+	 * So lets implement really simple and hopefully bullet-proof handler:
+	 * It does not really matter which IRQ we handle, we just go and
+	 * re-read all interesting statuses + give the framework a nudge.
+	 *
+	 * Other option would be building a _complex_ and error prone logic
+	 * trying to decide what could have been changed (resulting this IRQ
+	 * we are now handling). During the normal operation the BD99954 does
+	 * not seem to be generating much of interrupts so benefit from such
+	 * logic would probably be minimal.
+	 */
+
+	ret = regmap_read(bd->rmap, INT0_STATUS, &status);
+	if (ret) {
+		dev_err(bd->dev, "Failed to read IRQ status\n");
+		return IRQ_NONE;
+	}
+
+	ret = regmap_field_read(bd->rmap_fields[F_INT0_SET], &mask);
+	if (ret) {
+		dev_err(bd->dev, "Failed to read IRQ mask\n");
+		return IRQ_NONE;
+	}
+
+	/* Handle only IRQs that are not masked */
+	status &= mask;
+	tmp = status;
+
+	/* The idiot bit does not represent any sub-registers */
+	tmp &= ~(IDI0T_BIT);
+
+	/*
+	 * mask and ack IRQs we will handle (+ the idiot bit)
+	 */
+	ret = regmap_field_write(bd->rmap_fields[F_INT0_SET], 0);
+	if (ret) {
+		dev_err(bd->dev, "Failed to mask F_INT0\n");
+		return IRQ_NONE;
+	}
+
+	ret = regmap_write(bd->rmap, INT0_STATUS, status);
+	if (ret) {
+		dev_err(bd->dev, "Failed to ack F_INT0\n");
+		goto err_umask;
+	}
+
+	for (i = ffs(tmp); i; i = ffs(tmp)) {
+		int sub_status, sub_mask;
+		int sub_status_reg[] = {
+			-1, INT1_STATUS, INT2_STATUS, INT3_STATUS, INT4_STATUS,
+			INT5_STATUS, INT6_STATUS, INT7_STATUS,
+		};
+		struct regmap_field *sub_mask_f[] = {
+			NULL, bd->rmap_fields[F_INT1_SET],
+			bd->rmap_fields[F_INT2_SET],
+			bd->rmap_fields[F_INT3_SET],
+			bd->rmap_fields[F_INT4_SET],
+			bd->rmap_fields[F_INT5_SET],
+			bd->rmap_fields[F_INT6_SET],
+			bd->rmap_fields[F_INT7_SET],
+		};
+
+		tmp &= ~(1 << (i - 1));
+
+		if (i - 1 > ARRAY_SIZE(sub_status_reg))
+			break;
+
+		/* Clear sub IRQs */
+		ret = regmap_read(bd->rmap, sub_status_reg[i-1], &sub_status);
+		if (ret) {
+			dev_err(bd->dev, "Failed to read IRQ sub-status\n");
+			goto err_umask;
+		}
+
+		ret = regmap_field_read(sub_mask_f[i-1], &sub_mask);
+		if (ret) {
+			dev_err(bd->dev, "Failed to read IRQ sub-mask\n");
+			goto err_umask;
+		}
+
+		/* Ack active sub-statuses */
+		sub_status &= sub_mask;
+
+		ret = regmap_write(bd->rmap, sub_status_reg[i-1], sub_status);
+		if (ret) {
+			dev_err(bd->dev, "Failed to ack sub-IRQ\n");
+			goto err_umask;
+		}
+	}
+
+	ret = regmap_field_write(bd->rmap_fields[F_INT0_SET], mask);
+	if (ret)
+		/* May as well retry once */
+		goto err_umask;
+
+	/* Read whole chip state */
+	ret = bd9995x_get_chip_state(bd, &state);
+	if (ret < 0) {
+		dev_err(bd->dev, "Failed to read chip state\n");
+	} else {
+		mutex_lock(&bd->lock);
+		bd->state = state;
+		mutex_unlock(&bd->lock);
+
+		power_supply_changed(bd->charger);
+	}
+
+	return IRQ_HANDLED;
+
+err_umask:
+	ret = regmap_field_write(bd->rmap_fields[F_INT0_SET], mask);
+	if (ret)
+		dev_err(bd->dev,
+		"Failed to un-mask F_INT0 - IRQ permanently disabled\n");
+
+	return IRQ_NONE;
+}
+
+static int bd9995x_chip_reset(struct bd9995x_device *bd)
+{
+	int ret, state;
+	int rst_check_counter = 10;
+	u16 tmp = ALLRST | OTPLD;
+
+	ret = regmap_raw_write(bd->rmap, SYSTEM_CTRL_SET, &tmp, 2);
+	if (ret < 0)
+		return ret;
+
+	do {
+		ret = regmap_field_read(bd->rmap_fields[F_OTPLD_STATE], &state);
+		if (ret)
+			return ret;
+
+		msleep(10);
+	} while (state == 0 && --rst_check_counter);
+
+	if (!rst_check_counter) {
+		dev_err(bd->dev, "chip reset not completed\n");
+		return -ETIMEDOUT;
+	}
+
+	tmp = 0;
+	ret = regmap_raw_write(bd->rmap, SYSTEM_CTRL_SET, &tmp, 2);
+
+	return ret;
+}
+
+static int bd9995x_hw_init(struct bd9995x_device *bd)
+{
+	int ret;
+	int i;
+	struct bd9995x_state state;
+	struct bd9995x_init_data *id = &bd->init_data;
+
+	const struct {
+		enum bd9995x_fields id;
+		u16 value;
+	} init_data[] = {
+		/* Enable the charging trigger after SDP charger attached */
+		{F_SDP_CHG_TRIG_EN,	1},
+		/* Enable charging trigger after SDP charger attached */
+		{F_SDP_CHG_TRIG,	1},
+		/* Disable charging trigger by BC1.2 detection */
+		{F_VBUS_BC_DISEN,	1},
+		/* Disable charging trigger by BC1.2 detection */
+		{F_VCC_BC_DISEN,	1},
+		/* Disable automatic limitation of the input current */
+		{F_ILIM_AUTO_DISEN,	1},
+		/* Select current limitation when SDP charger attached*/
+		{F_SDP_500_SEL,		1},
+		/* Select current limitation when DCP charger attached */
+		{F_DCP_2500_SEL,	1},
+		{F_VSYSREG_SET,		id->vsysreg_set},
+		/* Activate USB charging and DC/DC converter */
+		{F_USB_SUS,		0},
+		/* DCDC clock: 1200 kHz*/
+		{F_DCDC_CLK_SEL,	3},
+		/* Enable charging */
+		{F_CHG_EN,		1},
+		/* Disable Input current Limit setting voltage measurement */
+		{F_EXTIADPEN,		0},
+		/* Disable input current limiting */
+		{F_VSYS_PRIORITY,	1},
+		{F_IBUS_LIM_SET,	id->ibus_lim_set},
+		{F_ICC_LIM_SET,		id->icc_lim_set},
+		/* Charge Termination Current Setting to 0*/
+		{F_ITERM_SET,		id->iterm_set},
+		/* Trickle-charge Current Setting */
+		{F_ITRICH_SET,		id->itrich_set},
+		/* Pre-charge Current setting */
+		{F_IPRECH_SET,		id->iprech_set},
+		/* Fast Charge Current for constant current phase */
+		{F_ICHG_SET,		id->ichg_set},
+		/* Fast Charge Voltage Regulation Setting */
+		{F_VFASTCHG_REG_SET1,	id->vfastchg_reg_set1},
+		/* Set Pre-charge Voltage Threshold for trickle charging. */
+		{F_VPRECHG_TH_SET,	id->vprechg_th_set},
+		{F_VRECHG_SET,		id->vrechg_set},
+		{F_VBATOVP_SET,		id->vbatovp_set},
+		/* Reverse buck boost voltage Setting */
+		{F_VRBOOST_SET,		0},
+		/* Disable fast-charging watchdog */
+		{F_WDT_FST,		0},
+		/* Disable pre-charging watchdog */
+		{F_WDT_PRE,		0},
+		/* power save off */
+		{F_POWER_SAVE_MODE,	0},
+		{F_INT1_SET,		INT1_ALL},
+		{F_INT2_SET,		INT2_ALL},
+		{F_INT3_SET,		INT3_ALL},
+		{F_INT4_SET,		INT4_ALL},
+		{F_INT5_SET,		INT5_ALL},
+		{F_INT6_SET,		INT6_ALL},
+		{F_INT7_SET,		INT7_ALL},
+	};
+
+	/*
+	 * Currently we initialize charger to a known state at startup.
+	 * If we want to allow for example the boot code to initialize
+	 * charger we should get rid of this.
+	 */
+	ret = bd9995x_chip_reset(bd);
+	if (ret < 0)
+		return ret;
+
+	/* initialize currents/voltages and other parameters */
+	for (i = 0; i < ARRAY_SIZE(init_data); i++) {
+		ret = regmap_field_write(bd->rmap_fields[init_data[i].id],
+					 init_data[i].value);
+		if (ret) {
+			dev_err(bd->dev, "failed to initialize charger (%d)\n",
+				ret);
+			return ret;
+		}
+	}
+
+	ret = bd9995x_get_chip_state(bd, &state);
+	if (ret < 0)
+		return ret;
+
+	mutex_lock(&bd->lock);
+	bd->state = state;
+	mutex_unlock(&bd->lock);
+
+	return 0;
+}
+
+static enum power_supply_property bd9995x_power_supply_props[] = {
+	POWER_SUPPLY_PROP_MANUFACTURER,
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_ONLINE,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT,
+	POWER_SUPPLY_PROP_CHARGE_AVG,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX,
+	POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE,
+	POWER_SUPPLY_PROP_CHARGE_TERM_CURRENT,
+	/* Battery props we access through charger */
+	POWER_SUPPLY_PROP_PRESENT,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CHARGE_TYPE,
+	POWER_SUPPLY_PROP_HEALTH,
+	POWER_SUPPLY_PROP_TEMP,
+	POWER_SUPPLY_PROP_TECHNOLOGY,
+	POWER_SUPPLY_PROP_MODEL_NAME,
+};
+
+static const struct power_supply_desc bd9995x_power_supply_desc = {
+	.name = "bd9995x-charger",
+	.type = POWER_SUPPLY_TYPE_USB,
+	.properties = bd9995x_power_supply_props,
+	.num_properties = ARRAY_SIZE(bd9995x_power_supply_props),
+	.get_property = bd9995x_power_supply_get_property,
+};
+
+/*
+ * Limit configurations for vbus-input-current and vcc-vacp-input-current
+ * Minimum limit is 0 uA. Max is 511 * 32000 uA = 16352000 uA. This is
+ * configured by writing a register so that each increment in register
+ * value equals to 32000 uA limit increment.
+ *
+ * Eg, value 0x0 is limit 0, value 0x1 is limit 32000, ...
+ * Describe the setting in linear_range table.
+ */
+static const struct linear_range input_current_limit_ranges[] = {
+	{
+		.min = 0,
+		.step = 32000,
+		.min_sel = 0x0,
+		.max_sel = 0x1ff,
+	},
+};
+
+/* Possible trickle, pre-charging and termination current values */
+static const struct linear_range charging_current_ranges[] = {
+	{
+		.min = 0,
+		.step = 64000,
+		.min_sel = 0x0,
+		.max_sel = 0x10,
+	}, {
+		.min = 1024000,
+		.step = 0,
+		.min_sel = 0x11,
+		.max_sel = 0x1f,
+	},
+};
+
+/*
+ * Fast charging voltage regulation, starting re-charging limit
+ * and battery over voltage protection have same possible values
+ */
+static const struct linear_range charge_voltage_regulation_ranges[] = {
+	{
+		.min = 2560000,
+		.step = 0,
+		.min_sel = 0,
+		.max_sel = 0xA0,
+	}, {
+		.min = 2560000,
+		.step = 16000,
+		.min_sel = 0xA0,
+		.max_sel = 0x4B0,
+	}, {
+		.min = 19200000,
+		.step = 0,
+		.min_sel = 0x4B0,
+		.max_sel = 0x7FF,
+	},
+};
+
+/* Possible VSYS voltage regulation values */
+static const struct linear_range vsys_voltage_regulation_ranges[] = {
+	{
+		.min = 2560000,
+		.step = 0,
+		.min_sel = 0,
+		.max_sel = 0x28,
+	}, {
+		.min = 2560000,
+		.step = 64000,
+		.min_sel = 0x28,
+		.max_sel = 0x12C,
+	}, {
+		.min = 19200000,
+		.step = 0,
+		.min_sel = 0x12C,
+		.max_sel = 0x1FF,
+	},
+};
+
+/* Possible settings for switching from trickle to pre-charging limits */
+static const struct linear_range trickle_to_pre_threshold_ranges[] = {
+	{
+		.min = 2048000,
+		.step = 0,
+		.min_sel = 0,
+		.max_sel = 0x20,
+	}, {
+		.min = 2048000,
+		.step = 64000,
+		.min_sel = 0x20,
+		.max_sel = 0x12C,
+	}, {
+		.min = 19200000,
+		.step = 0,
+		.min_sel = 0x12C,
+		.max_sel = 0x1FF
+	}
+};
+
+/* Possible current values for fast-charging constant current phase */
+static const struct linear_range fast_charge_current_ranges[] = {
+	{
+		.min = 0,
+		.step = 64000,
+		.min_sel = 0,
+		.max_sel = 0xFF,
+	}
+};
+
+struct battery_init {
+	const char *name;
+	int *info_data;
+	const struct linear_range *range;
+	int ranges;
+	u16 *data;
+};
+
+struct dt_init {
+	char *prop;
+	const struct linear_range *range;
+	int ranges;
+	u16 *data;
+};
+
+static int bd9995x_fw_probe(struct bd9995x_device *bd)
+{
+	int ret;
+	struct power_supply_battery_info info;
+	u32 property;
+	int i;
+	int regval;
+	bool found;
+	struct bd9995x_init_data *init = &bd->init_data;
+	struct battery_init battery_inits[] = {
+		{
+			.name = "trickle-charging current",
+			.info_data = &info.tricklecharge_current_ua,
+			.range = &charging_current_ranges[0],
+			.ranges = 2,
+			.data = &init->itrich_set,
+		}, {
+			.name = "pre-charging current",
+			.info_data = &info.precharge_current_ua,
+			.range = &charging_current_ranges[0],
+			.ranges = 2,
+			.data = &init->iprech_set,
+		}, {
+			.name = "pre-to-trickle charge voltage threshold",
+			.info_data = &info.precharge_voltage_max_uv,
+			.range = &trickle_to_pre_threshold_ranges[0],
+			.ranges = 2,
+			.data = &init->vprechg_th_set,
+		}, {
+			.name = "charging termination current",
+			.info_data = &info.charge_term_current_ua,
+			.range = &charging_current_ranges[0],
+			.ranges = 2,
+			.data = &init->iterm_set,
+		}, {
+			.name = "charging re-start voltage",
+			.info_data = &info.charge_restart_voltage_uv,
+			.range = &charge_voltage_regulation_ranges[0],
+			.ranges = 2,
+			.data = &init->vrechg_set,
+		}, {
+			.name = "battery overvoltage limit",
+			.info_data = &info.overvoltage_limit_uv,
+			.range = &charge_voltage_regulation_ranges[0],
+			.ranges = 2,
+			.data = &init->vbatovp_set,
+		}, {
+			.name = "fast-charging max current",
+			.info_data = &info.constant_charge_current_max_ua,
+			.range = &fast_charge_current_ranges[0],
+			.ranges = 1,
+			.data = &init->ichg_set,
+		}, {
+			.name = "fast-charging voltage",
+			.info_data = &info.constant_charge_voltage_max_uv,
+			.range = &charge_voltage_regulation_ranges[0],
+			.ranges = 2,
+			.data = &init->vfastchg_reg_set1,
+		},
+	};
+	struct dt_init props[] = {
+		{
+			.prop = "rohm,vsys-regulation-microvolt",
+			.range = &vsys_voltage_regulation_ranges[0],
+			.ranges = 2,
+			.data = &init->vsysreg_set,
+		}, {
+			.prop = "rohm,vbus-input-current-limit-microamp",
+			.range = &input_current_limit_ranges[0],
+			.ranges = 1,
+			.data = &init->ibus_lim_set,
+		}, {
+			.prop = "rohm,vcc-input-current-limit-microamp",
+			.range = &input_current_limit_ranges[0],
+			.ranges = 1,
+			.data = &init->icc_lim_set,
+		},
+	};
+
+	/*
+	 *  the power_supply_get_battery_info does not support getting values
+	 * from ACPI. Let's fix it if required :)
+	 */
+	ret = power_supply_get_battery_info(bd->charger, &info);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < ARRAY_SIZE(battery_inits); i++) {
+		int val = *battery_inits[i].info_data;
+		const struct linear_range *range = battery_inits[i].range;
+		int ranges = battery_inits[i].ranges;
+
+		if (val == -EINVAL)
+			continue;
+
+		ret = linear_range_get_selector_low_array(range, ranges, val,
+							  &regval, &found);
+		if (ret) {
+			dev_err(bd->dev, "Unsupported value for %s\n",
+				battery_inits[i].name);
+
+			power_supply_put_battery_info(bd->charger, &info);
+			return -EINVAL;
+		}
+		if (!found) {
+			dev_warn(bd->dev,
+				 "Unsupported value for %s - using smaller\n",
+				 battery_inits[i].name);
+		}
+		*(battery_inits[i].data) = regval;
+	}
+
+	power_supply_put_battery_info(bd->charger, &info);
+
+	for (i = 0; i < ARRAY_SIZE(props); i++) {
+		ret = device_property_read_u32(bd->dev, props[i].prop,
+					       &property);
+		if (ret < 0) {
+			dev_err(bd->dev, "failed to read %s", props[i].prop);
+
+			return ret;
+		}
+
+		ret = linear_range_get_selector_low_array(props[i].range,
+							  props[i].ranges,
+							  property, &regval,
+							  &found);
+		if (ret) {
+			dev_err(bd->dev, "Unsupported value for '%s'\n",
+				props[i].prop);
+
+			return -EINVAL;
+		}
+
+		if (!found) {
+			dev_warn(bd->dev,
+				 "Unsupported value for '%s' - using smaller\n",
+				 props[i].prop);
+		}
+
+		*(props[i].data) = regval;
+	}
+
+	return 0;
+}
+
+static int bd9995x_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct bd9995x_device *bd;
+	struct power_supply_config psy_cfg = {};
+	int ret;
+	int i;
+
+	bd = devm_kzalloc(dev, sizeof(*bd), GFP_KERNEL);
+	if (!bd)
+		return -ENOMEM;
+
+	bd->client = client;
+	bd->dev = dev;
+	psy_cfg.drv_data = bd;
+	psy_cfg.of_node = dev->of_node;
+
+	mutex_init(&bd->lock);
+
+	bd->rmap = devm_regmap_init_i2c(client, &bd9995x_regmap_config);
+	if (IS_ERR(bd->rmap)) {
+		dev_err(dev, "Failed to setup register access via i2c\n");
+		return PTR_ERR(bd->rmap);
+	}
+
+	for (i = 0; i < ARRAY_SIZE(bd9995x_reg_fields); i++) {
+		const struct reg_field *reg_fields = bd9995x_reg_fields;
+
+		bd->rmap_fields[i] = devm_regmap_field_alloc(dev, bd->rmap,
+							     reg_fields[i]);
+		if (IS_ERR(bd->rmap_fields[i])) {
+			dev_err(dev, "cannot allocate regmap field\n");
+			return PTR_ERR(bd->rmap_fields[i]);
+		}
+	}
+
+	i2c_set_clientdata(client, bd);
+
+	ret = regmap_field_read(bd->rmap_fields[F_CHIP_ID], &bd->chip_id);
+	if (ret) {
+		dev_err(dev, "Cannot read chip ID.\n");
+		return ret;
+	}
+
+	if (bd->chip_id != BD99954_ID) {
+		dev_err(dev, "Chip with ID=0x%x, not supported!\n",
+			bd->chip_id);
+		return -ENODEV;
+	}
+
+	ret = regmap_field_read(bd->rmap_fields[F_CHIP_REV], &bd->chip_rev);
+	if (ret) {
+		dev_err(dev, "Cannot read revision.\n");
+		return ret;
+	}
+
+	dev_info(bd->dev, "Found DB99954 chip rev %d\n", bd->chip_rev);
+
+	/*
+	 * We need to init the psy before we can call
+	 * power_supply_get_battery_info() for it
+	 */
+	bd->charger = devm_power_supply_register(bd->dev,
+						 &bd9995x_power_supply_desc,
+						&psy_cfg);
+	if (IS_ERR(bd->charger)) {
+		dev_err(dev, "Failed to register power supply\n");
+		return PTR_ERR(bd->charger);
+	}
+
+	if (!dev->platform_data) {
+		ret = bd9995x_fw_probe(bd);
+		if (ret < 0) {
+			dev_err(dev, "Cannot read device properties.\n");
+			return ret;
+		}
+	} else {
+		return -ENODEV;
+	}
+
+	ret = bd9995x_hw_init(bd);
+	if (ret < 0) {
+		dev_err(dev, "Cannot initialize the chip.\n");
+		return ret;
+	}
+
+	return devm_request_threaded_irq(dev, client->irq, NULL,
+					 bd9995x_irq_handler_thread,
+					 IRQF_TRIGGER_LOW | IRQF_ONESHOT,
+					 BD9995X_IRQ_PIN, bd);
+}
+
+static int bd9995x_remove(struct i2c_client *client)
+{
+	int ret;
+	struct bd9995x_device *bd = i2c_get_clientdata(client);
+
+	disable_irq(client->irq);
+
+	/*
+	 * reset all registers to default values. This should also disable
+	 * CHG_EN bit. If this is not required we can get rid of the remove.
+	 */
+	ret = bd9995x_chip_reset(bd);
+
+	dev_info(bd->dev, "Driver for DB99954 chip removed\n");
+
+	return 0;
+}
+
+static const struct of_device_id bd9995x_of_match[] = {
+	{ .compatible = "rohm,bd9995x-charger", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, bd9995x_of_match);
+
+static const struct acpi_device_id bd9995x_acpi_match[] = {
+	{"BD999540", 0},
+	{},
+};
+MODULE_DEVICE_TABLE(acpi, bd9995x_acpi_match);
+
+static struct i2c_driver bd9995x_driver = {
+	.driver = {
+		.name = "bd9995x-charger",
+		.of_match_table = of_match_ptr(bd9995x_of_match),
+		.acpi_match_table = ACPI_PTR(bd9995x_acpi_match),
+	},
+	.probe = bd9995x_probe,
+	.remove = bd9995x_remove,
+};
+module_i2c_driver(bd9995x_driver);
+
+MODULE_AUTHOR("Laine Markus <markus.laine@xxxxxxxxxxxxxxxxx>");
+MODULE_DESCRIPTION("ROHM BD99954 charger driver");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/power/bd99954-charger.h b/include/linux/power/bd99954-charger.h
new file mode 100644
index 000000000000..f58897925383
--- /dev/null
+++ b/include/linux/power/bd99954-charger.h
@@ -0,0 +1,1075 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2020 ROHM Semiconductors */
+#ifndef BD99954_CHARGER_H
+#define BD99954_CHARGER_H
+
+#include <linux/regmap.h>
+
+#define BD9995X_MANUFACTURER "Rohm Semiconductor"
+#define BD9995X_IRQ_PIN      "bd9995x_irq"
+
+#define BD9995X_VSYS_PRECHARGE_OFFSET_MV 200
+
+#define BD99954_ID            0x346
+#define BD99955_ID            0x221
+#define BD99956_ID            0x331
+
+/* Battery Charger Commands */
+#define    CHARGING_CURRENT   0x14
+#define    CHARGING_VOLTAGE   0x15
+#define    PROTECT_SET        0x3E
+#define    MAP_SET            0x3F
+
+/* Extended commands */
+#define    CHGSTM_STATUS       0x100
+#define    VBAT_VSYS_STATUS    0x101
+#define    VBUS_VCC_STATUS     0x102
+#define    CHGOP_STATUS        0x103
+#define    WDT_STATUS          0x104
+#define    CUR_ILIM_VAL        0x105
+#define    SEL_ILIM_VAL        0x106
+#define    IBUS_LIM_SET        0x107
+#define    ICC_LIM_SET         0x108
+#define    IOTG_LIM_SET        0x109
+#define    VIN_CTRL_SET        0x10A
+#define    CHGOP_SET1          0x10B
+#define    CHGOP_SET2          0x10C
+#define    VBUSCLPS_TH_SET     0x10D
+#define    VCCCLPS_TH_SET      0x10E
+#define    CHGWDT_SET          0x10F
+#define    BATTWDT_SET         0x110
+#define    VSYSREG_SET         0x111
+#define    VSYSVAL_THH_SET     0x112
+#define    VSYSVAL_THL_SET     0x113
+#define    ITRICH_SET          0x114
+#define    IPRECH_SET          0x115
+#define    ICHG_SET            0x116
+#define    ITERM_SET           0x117
+#define    VPRECHG_TH_SET      0x118
+#define    VRBOOST_SET         0x119
+#define    VFASTCHG_REG_SET1   0x11A
+#define    VFASTCHG_REG_SET2   0x11B
+#define    VFASTCHG_REG_SET3   0x11C
+#define    VRECHG_SET          0x11D
+#define    VBATOVP_SET         0x11E
+#define    IBATSHORT_SET       0x11F
+#define    PROCHOT_CTRL_SET    0x120
+#define    PROCHOT_ICRIT_SET   0x121
+#define    PROCHOT_INORM_SET   0x122
+#define    PROCHOT_IDCHG_SET   0x123
+#define    PROCHOT_VSYS_SET    0x124
+#define    PMON_IOUT_CTRL_SET  0x125
+#define    PMON_DACIN_VAL      0x126
+#define    IOUT_DACIN_VAL      0x127
+#define    VCC_UCD_SET         0x128
+#define    VCC_UCD_STATUS      0x129
+#define    VCC_IDD_STATUS      0x12A
+#define    VCC_UCD_FCTRL_SET   0x12B
+#define    VCC_UCD_FCTRL_EN    0x12C
+#define    VBUS_UCD_SET        0x130
+#define    VBUS_UCD_STATUS     0x131
+#define    VBUS_IDD_STATUS     0x132
+#define    VBUS_UCD_FCTRL_SET  0x133
+#define    VBUS_UCD_FCTRL_EN   0x134
+#define    CHIP_ID             0x138
+#define    CHIP_REV            0x139
+#define    IC_SET1             0x13A
+#define    IC_SET2             0x13B
+#define    SYSTEM_STATUS       0x13C
+#define    SYSTEM_CTRL_SET     0x13D
+#define    VM_CTRL_SET         0x140
+#define    THERM_WINDOW_SET1   0x141
+#define    THERM_WINDOW_SET2   0x142
+#define    THERM_WINDOW_SET3   0x143
+#define    THERM_WINDOW_SET4   0x144
+#define    THERM_WINDOW_SET5   0x145
+#define    IBATP_TH_SET        0x146
+#define    IBATM_TH_SET        0x147
+#define    VBAT_TH_SET         0x148
+#define    THERM_TH_SET        0x149
+#define    IACP_TH_SET         0x14A
+#define    VACP_TH_SET         0x14B
+#define    VBUS_TH_SET         0x14C
+#define    VCC_TH_SET          0x14D
+#define    VSYS_TH_SET         0x14E
+#define    EXTIADP_TH_SET      0x14F
+#define    IBATP_VAL           0x150
+#define    IBATP_AVE_VAL       0x151
+#define    IBATM_VAL           0x152
+#define    IBATM_AVE_VAL       0x153
+#define    VBAT_VAL            0x154
+#define    VBAT_AVE_VAL        0x155
+#define    THERM_VAL           0x156
+#define    VTH_VAL             0x157
+#define    IACP_VAL            0x158
+#define    IACP_AVE_VAL        0x159
+#define    VACP_VAL            0x15A
+#define    VACP_AVE_VAL        0x15B
+#define    VBUS_VAL            0x15C
+#define    VBUS_AVE_VAL        0x15D
+#define    VCC_VAL             0x15E
+#define    VCC_AVE_VAL         0x15F
+#define    VSYS_VAL            0x160
+#define    VSYS_AVE_VAL        0x161
+#define    EXTIADP_VAL         0x162
+#define    EXTIADP_AVE_VAL     0x163
+#define    VACPCLPS_TH_SET     0x164
+#define    INT0_SET            0x168
+#define    INT1_SET            0x169
+#define    INT2_SET            0x16A
+#define    INT3_SET            0x16B
+#define    INT4_SET            0x16C
+#define    INT5_SET            0x16D
+#define    INT6_SET            0x16E
+#define    INT7_SET            0x16F
+#define    INT0_STATUS         0x170
+#define    INT1_STATUS         0x171
+#define    INT2_STATUS         0x172
+#define    INT3_STATUS         0x173
+#define    INT4_STATUS         0x174
+#define    INT5_STATUS         0x175
+#define    INT6_STATUS         0x176
+#define    INT7_STATUS         0x177
+#define    OTPREG0             0x17A
+#define    OTPREG1             0x17B
+#define    SMBREG              0x17C
+#define    DEBUG_MODE_SET      0x17F
+#define    DEBUG0x14           0x214
+#define    DEBUG0x1A           0x21A
+
+enum bd9995x_fields {
+	F_PREV_CHGSTM_STATE, F_CHGSTM_STATE,
+	F_VBAT_VSYS_STATUS,
+	F_VBUS_VCC_STATUS,
+	F_BATTEMP, F_VRECHG_DET, F_RBOOST_UV, F_RBOOSTS,
+	F_THERMWDT_VAL, F_CHGWDT_VAL,
+	F_CUR_ILIM_VAL,
+	F_SEL_ILIM_VAL,
+	F_IBUS_LIM_SET,
+	F_ICC_LIM_SET,
+	F_IOTG_LIM_SET,
+	F_OTG_BOTH_EN,
+	F_VRBOOST_TRIG,
+	F_VRBOOST_EN,
+	F_PP_BOTH_THRU,
+	F_VIN_ORD,
+	F_VBUS_EN,
+	F_VCC_EN,
+	F_VSYS_PRIORITY,
+	F_PPC_SUB_CAP,
+	F_PPC_CAP,
+	F_DCP_2500_SEL,
+	F_SDP_500_SEL,
+	F_ILIM_AUTO_DISEN,
+	F_VCC_BC_DISEN,
+	F_VBUS_BC_DISEN,
+	F_SDP_CHG_TRIG_EN,
+	F_SDP_CHG_TRIG,
+	F_AUTO_TOF,
+	F_AUTO_FST,
+	F_AUTO_RECH,
+	F_ILIM_RESET_EN,
+	F_DCDC_1MS_SEL,
+	F_SEL_ILIM_DIV,
+	F_BATT_LEARN,
+	F_CHG_EN,
+	F_USB_SUS,
+	F_CHOP_SS_INIT,
+	F_CHOP_ALL_INIT,
+	F_DCDC_CLK_SEL,
+	F_CHOP_SS,
+	F_CHOP_ALL,
+	F_VBUSCLPS_TH_SET,
+	F_VCCCLPS_TH_SET,
+	F_WDT_FST,
+	F_WDT_PRE,
+	F_WDT_IBAT_SHORT,
+	F_WDT_THERM,
+	F_VSYSREG_SET,
+	F_VSYSVAL_THH_SET,
+	F_VSYSVAL_THL_SET,
+	F_ITRICH_SET,
+	F_IPRECH_SET,
+	F_ICHG_SET,
+	F_ITERM_SET,
+	F_VPRECHG_TH_SET,
+	F_VRBOOST_SET,
+	F_VFASTCHG_REG_SET1,
+	F_VFASTCHG_REG_SET2,
+	F_VFASTCHG_REG_SET3,
+	F_VRECHG_SET,
+	F_VBATOVP_SET,
+	F_IBATM_SHORT_SET,
+	F_PROCHOT_DG_SET,
+	F_PROCHOT_ICRIT_DG_SET,
+	F_PROCHOT_IDCHG_DG_SET,
+	F_PROCHOT_EN,
+	F_PROCHOT_ICRIT_SET,
+	F_PROCHOT_INORM_SET,
+	F_PROCHOT_IDCHG_SET,
+	F_PROCHOT_VSYS_SET,
+	F_IMON_INSEL,
+	F_PMON_INSEL,
+	F_IOUT_OUT_EN,
+	F_IOUT_SOURCE_SEL,
+	F_IOUT_GAIN_SET,
+	F_PMON_OUT_EN,
+	F_PMON_GAIN_SET,
+	F_PMON_DACIN_VAL,
+	F_IOUT_DACIN_VAL,
+	F_VCC_BCSRETRY,
+	F_VCC_ADCRTRY,
+	F_VCC_USBDETEN,
+	F_VCC_IDRDETEN,
+	F_VCC_ENUMRDY,
+	F_VCC_ADCPOLEN,
+	F_VCC_DCDMODE,
+	F_VCC_USB_SW_EN,
+	F_VCC_USB_SW,
+	F_VCC_DCDFAIL,
+	F_VCC_CHGPORT,
+	F_VCC_PUPDET,
+	F_VCC_VBUS_VLD,
+	F_VCC_CHGDET,
+	F_VCC_OTGDET,
+	F_VCC_VBINOP,
+	F_VCC_EXTID,
+	F_VCC_IDRDET,
+	F_VCC_INDO,
+	F_VCC_UCDSWEN,
+	F_VCC_RREF_EN,
+	F_VCC_DPPU_EN,
+	F_VCC_DPREF_EN,
+	F_VCC_DMREF_EN,
+	F_VCC_DPDET_EN,
+	F_VCC_DMDET_EN,
+	F_VCC_DPSINK_EN,
+	F_VCC_DMSINK_EN,
+	F_VCC_DP_BUFF_EN,
+	F_VCC_DM_BUFF_EN,
+	F_VCC_EXTCLKENBL,
+	F_VCC_PLSTESTEN,
+	F_VCC_UCDSWEN_TSTENB,
+	F_VCC_RREF_EN_TSTENB,
+	F_VCC_DPPU_EN_TSTENB,
+	F_VCC_DPREF_EN_TSTENB,
+	F_VCC_DMREF_EN_TSTENB,
+	F_VCC_DPDET_EN_TSTENB,
+	F_VCC_DMDET_EN_TSTENB,
+	F_VCC_DPSINK_EN_TSTENB,
+	F_VCC_DMSINK_EN_TSTENB,
+	F_VCC_DP_BUFF_EN_TSTENB,
+	F_VCC_DM_BUFF_EN_TSTENB,
+	F_VBUS_BCSRETRY,
+	F_VBUS_ADCRTRY,
+	F_VBUS_USBDETEN,
+	F_VBUS_IDRDETEN,
+	F_VBUS_ENUMRDY,
+	F_VBUS_ADCPOLEN,
+	F_VBUS_DCDMODE,
+	F_VBUS_USB_SW_EN,
+	F_VBUS_USB_SW,
+	F_VBUS_DCDFAIL,
+	F_VBUS_CHGPORT,
+	F_VBUS_PUPDET,
+	F_VBUS_VBUS_VLD,
+	F_VBUS_CHGDET,
+	F_VBUS_OTGDET,
+	F_VBUS_VBINOP,
+	F_VBUS_EXTID,
+	F_VBUS_IDRDET,
+	F_VBUS_INDO,
+	F_VBUS_UCDSWEN,
+	F_VBUS_RREF_EN,
+	F_VBUS_DPPU_EN,
+	F_VBUS_DPREF_EN,
+	F_VBUS_DMREF_EN,
+	F_VBUS_DPDET_EN,
+	F_VBUS_DMDET_EN,
+	F_VBUS_DPSINK_EN,
+	F_VBUS_DMSINK_EN,
+	F_VBUS_DP_BUFF_EN,
+	F_VBUS_DM_BUFF_EN,
+	F_VBUS_EXTCLKENBL,
+	F_VBUS_PLSTESTEN,
+	F_VBUS_UCDSWEN_TSTENB,
+	F_VBUS_RREF_EN_TSTENB,
+	F_VBUS_DPPU_EN_TSTENB,
+	F_VBUS_DPREF_EN_TSTENB,
+	F_VBUS_DMREF_EN_TSTENB,
+	F_VBUS_DPDET_EN_TSTENB,
+	F_VBUS_DMDET_EN_TSTENB,
+	F_VBUS_DPSINK_EN_TSTENB,
+	F_VBUS_DMSINK_EN_TSTENB,
+	F_VBUS_DP_BUFF_EN_TSTENB,
+	F_VBUS_DM_BUFF_EN_TSTENB,
+	F_CHIP_ID,
+	F_CHIP_REV,
+	F_ONE_CELL_MODE,
+	F_cell,
+	F_VACP_AUTO_DISCHG,
+	F_VACP_LOAD,
+	F_ACOK_POL,
+	F_ACOK_DISEN,
+	F_DEBUG_SET1,
+	F_DEBUG_SET0,
+	F_MONRST_STATE,
+	F_ALMRST_STATE,
+	F_CHGRST_STATE,
+	F_OTPLD_STATE,
+	F_ALLRST_STATE,
+	F_PROTECT_SET,
+	F_MAP_SET,
+	F_ADCINTERVAL,
+	F_ADCMOD,
+	F_ADCTMOD,
+	F_EXTIADPEN,
+	F_VSYSENB,
+	F_VCCENB,
+	F_VBUSENB,
+	F_VACPENB,
+	F_IACPENB,
+	F_THERMENB,
+	F_VBATENB,
+	F_IBATMENB,
+	F_IBATPENB,
+	F_TMPTHR1B,
+	F_TMPTHR1A,
+	F_TMPTHR2B,
+	F_TMPTHR2A,
+	F_TMPTHR3B,
+	F_TMPTHR3A,
+	F_TMPTHR4B,
+	F_TMPTHR4A,
+	F_TMPTHR5B,
+	F_TMPTHR5A,
+	F_IBATP_TH_SET,
+	F_IBATM_TH_SET,
+	F_VBAT_TH_SET,
+	F_THERM_TH_SET,
+	F_IACP_TH_SET,
+	F_VACP_TH_SET,
+	F_VBUS_TH_SET,
+	F_VCC_TH_SET,
+	F_VSYS_TH_SET,
+	F_EXTIADP_TH_SET,
+	F_IBATP_VAL,
+	F_IBATP_AVE_VAL,
+	F_IBATM_VAL,
+	F_IBATM_AVE_VAL,
+	F_VBAT_VAL,
+	F_VBAT_AVE_VAL,
+	F_THERM_VAL,
+	F_VTH_VAL,
+	F_IACP_VAL,
+	F_IACP_AVE_VAL,
+	F_VACP_VAL,
+	F_VACP_AVE_VAL,
+	F_VBUS_VAL,
+	F_VBUS_AVE_VAL,
+	F_VCC_VAL,
+	F_VCC_AVE_VAL,
+	F_VSYS_VAL,
+	F_VSYS_AVE_VAL,
+	F_EXTIADP_VAL,
+	F_EXTIADP_AVE_VAL,
+	F_VACPCLPS_TH_SET,
+	F_INT7_SET,
+	F_INT6_SET,
+	F_INT5_SET,
+	F_INT4_SET,
+	F_INT3_SET,
+	F_INT2_SET,
+	F_INT1_SET,
+	F_INT0_SET,
+	F_VBUS_RBUV_DET,
+	F_VBUS_RBUV_RES,
+	F_VBUS_TH_DET,
+	F_VBUS_TH_RES,
+	F_VBUS_IIN_MOD,
+	F_VBUS_OV_DET,
+	F_VBUS_OV_RES,
+	F_VBUS_CLPS_DET,
+	F_VBUS_CLPS,
+	F_VBUS_DET,
+	F_VBUS_RES,
+	F_VCC_RBUV_DET,
+	F_VCC_RBUV_RES,
+	F_VCC_TH_DET,
+	F_VCC_TH_RES,
+	F_VCC_IIN_MOD,
+	F_VCC_OVP_DET,
+	F_VCC_OVP_RES,
+	F_VCC_CLPS_DET,
+	F_VCC_CLPS_RES,
+	F_VCC_DET,
+	F_VCC_RES,
+	F_TH_DET,
+	F_TH_RMV,
+	F_TMP_OUT_DET,
+	F_TMP_OUT_RES,
+	F_VBAT_TH_DET,
+	F_VBAT_TH_RES,
+	F_IBAT_SHORT_DET,
+	F_IBAT_SHORT_RES,
+	F_VBAT_OV_DET,
+	F_VBAT_OV_RES,
+	F_BAT_ASSIST_DET,
+	F_BAT_ASSIST_RES,
+	F_VSYS_TH_DET,
+	F_VSYS_TH_RES,
+	F_VSYS_OV_DET,
+	F_VSYS_OV_RES,
+	F_VSYS_SHT_DET,
+	F_VSYS_SHT_RES,
+	F_VSYS_UV_DET,
+	F_VSYS_UV_RES,
+	F_OTP_LOAD_DONE,
+	F_PWR_ON,
+	F_EXTIADP_TRNS,
+	F_EXTIADP_TH_DET,
+	F_EXIADP_TH_RES,
+	F_BAT_MNT_DET,
+	F_BAT_MNT_RES,
+	F_TSD_DET,
+	F_TSD_RES,
+	F_CHGWDT_EXP,
+	F_THERMWDT_EXP,
+	F_TMP_TRNS,
+	F_CHG_TRNS,
+	F_VBUS_UCD_PORT_DET,
+	F_VBUS_UCD_UCHG_DET,
+	F_VBUS_UCD_URID_RMV,
+	F_VBUS_UCD_OTG_DET,
+	F_VBUS_UCD_URID_MOD,
+	F_VCC_UCD_PORT_DET,
+	F_VCC_UCD_UCHG_DET,
+	F_VCC_UCD_URID_RMV,
+	F_VCC_UCD_OTG_DET,
+	F_VCC_UCD_URID_MOD,
+	F_PROCHOT_DET,
+	F_PROCHOT_RES,
+	F_VACP_DET,
+	F_VACP_RES,
+	F_VACP_TH_DET,
+	F_VACP_TH_RES,
+	F_IACP_TH_DET,
+	F_IACP_THE_RES,
+	F_THERM_TH_DET,
+	F_THERM_TH_RES,
+	F_IBATM_TH_DET,
+	F_IBATM_TH_RES,
+	F_IBATP_TH_DET,
+	F_IBATP_TH_RES,
+	F_INT7_STATUS,
+	F_INT6_STATUS,
+	F_INT5_STATUS,
+	F_INT4_STATUS,
+	F_INT3_STATUS,
+	F_INT2_STATUS,
+	F_INT1_STATUS,
+	F_INT0_STATUS,
+	F_ILIM_DECREASE,
+	F_RESERVE_OTPREG1,
+	F_POWER_SAVE_MODE,
+	F_DEBUG_MODE_SET,
+	F_DEBUG0x14,
+	F_DEBUG0x1A,
+	F_MAX_FIELDS
+};
+
+static const struct reg_field bd9995x_reg_fields[] = {
+	    [F_PREV_CHGSTM_STATE] = REG_FIELD(CHGSTM_STATUS, 8, 14),
+	    [F_CHGSTM_STATE] = REG_FIELD(CHGSTM_STATUS, 0, 6),
+	    [F_VBAT_VSYS_STATUS] = REG_FIELD(VBAT_VSYS_STATUS, 0, 15),
+	    [F_VBUS_VCC_STATUS] = REG_FIELD(VBUS_VCC_STATUS, 0, 12),
+	    [F_BATTEMP] = REG_FIELD(CHGOP_STATUS, 8, 10),
+	    [F_VRECHG_DET] = REG_FIELD(CHGOP_STATUS, 6, 6),
+	    [F_RBOOST_UV] = REG_FIELD(CHGOP_STATUS, 1, 1),
+	    [F_RBOOSTS] = REG_FIELD(CHGOP_STATUS, 0, 0),
+	    [F_THERMWDT_VAL] = REG_FIELD(WDT_STATUS, 8, 15),
+	    [F_CHGWDT_VAL] = REG_FIELD(WDT_STATUS, 0, 7),
+	    [F_CUR_ILIM_VAL] = REG_FIELD(CUR_ILIM_VAL, 0, 13),
+	    [F_SEL_ILIM_VAL] = REG_FIELD(SEL_ILIM_VAL, 0, 13),
+	    [F_IBUS_LIM_SET] = REG_FIELD(IBUS_LIM_SET, 5, 13),
+	    [F_ICC_LIM_SET] = REG_FIELD(ICC_LIM_SET, 5, 13),
+	    [F_IOTG_LIM_SET] = REG_FIELD(IOTG_LIM_SET, 5, 13),
+	    [F_OTG_BOTH_EN] = REG_FIELD(VIN_CTRL_SET, 15, 15),
+	    [F_VRBOOST_TRIG] = REG_FIELD(VIN_CTRL_SET, 14, 14),
+	    [F_VRBOOST_EN] = REG_FIELD(VIN_CTRL_SET, 12, 13),
+	    [F_PP_BOTH_THRU] = REG_FIELD(VIN_CTRL_SET, 11, 11),
+	    [F_VIN_ORD] = REG_FIELD(VIN_CTRL_SET, 7, 7),
+	    [F_VBUS_EN] = REG_FIELD(VIN_CTRL_SET, 6, 6),
+	    [F_VCC_EN] = REG_FIELD(VIN_CTRL_SET, 5, 5),
+	    [F_VSYS_PRIORITY] = REG_FIELD(VIN_CTRL_SET, 4, 4),
+	    [F_PPC_SUB_CAP] = REG_FIELD(VIN_CTRL_SET, 2, 3),
+	    [F_PPC_CAP] = REG_FIELD(VIN_CTRL_SET, 0, 1),
+	    [F_DCP_2500_SEL] = REG_FIELD(CHGOP_SET1, 15, 15),
+	    [F_SDP_500_SEL] = REG_FIELD(CHGOP_SET1, 14, 14),
+	    [F_ILIM_AUTO_DISEN] = REG_FIELD(CHGOP_SET1, 13, 13),
+	    [F_VCC_BC_DISEN] = REG_FIELD(CHGOP_SET1, 11, 11),
+	    [F_VBUS_BC_DISEN] = REG_FIELD(CHGOP_SET1, 10, 10),
+	    [F_SDP_CHG_TRIG_EN] = REG_FIELD(CHGOP_SET1, 9, 9),
+	    [F_SDP_CHG_TRIG] = REG_FIELD(CHGOP_SET1, 8, 8),
+	    [F_AUTO_TOF] = REG_FIELD(CHGOP_SET1, 6, 6),
+	    [F_AUTO_FST] = REG_FIELD(CHGOP_SET1, 5, 5),
+	    [F_AUTO_RECH] = REG_FIELD(CHGOP_SET1, 3, 3),
+	    [F_ILIM_RESET_EN] = REG_FIELD(CHGOP_SET2, 14, 14),
+	    [F_DCDC_1MS_SEL] = REG_FIELD(CHGOP_SET2, 12, 13),
+	    [F_SEL_ILIM_DIV] = REG_FIELD(CHGOP_SET2, 10, 10),
+	    [F_BATT_LEARN] = REG_FIELD(CHGOP_SET2, 8, 8),
+	    [F_CHG_EN] = REG_FIELD(CHGOP_SET2, 7, 7),
+	    [F_USB_SUS] = REG_FIELD(CHGOP_SET2, 6, 6),
+	    [F_CHOP_SS_INIT] = REG_FIELD(CHGOP_SET2, 5, 5),
+	    [F_CHOP_ALL_INIT] = REG_FIELD(CHGOP_SET2, 4, 4),
+	    [F_DCDC_CLK_SEL] = REG_FIELD(CHGOP_SET2, 2, 3),
+	    [F_CHOP_SS] = REG_FIELD(CHGOP_SET2, 1, 1),
+	    [F_CHOP_ALL] = REG_FIELD(CHGOP_SET2, 0, 0),
+	    [F_VBUSCLPS_TH_SET] = REG_FIELD(VBUSCLPS_TH_SET, 7, 14),
+	    [F_VCCCLPS_TH_SET] = REG_FIELD(VCCCLPS_TH_SET, 7, 14),
+	    [F_WDT_FST] = REG_FIELD(CHGWDT_SET, 8, 15),
+	    [F_WDT_PRE] = REG_FIELD(CHGWDT_SET, 0, 7),
+	    [F_WDT_IBAT_SHORT] = REG_FIELD(BATTWDT_SET, 8, 15),
+	    [F_WDT_THERM] = REG_FIELD(BATTWDT_SET, 0, 7),
+	    [F_VSYSREG_SET] = REG_FIELD(VSYSREG_SET, 6, 14),
+	    [F_VSYSVAL_THH_SET] = REG_FIELD(VSYSVAL_THH_SET, 6, 14),
+	    [F_VSYSVAL_THL_SET] = REG_FIELD(VSYSVAL_THL_SET, 6, 14),
+	    [F_ITRICH_SET] = REG_FIELD(ITRICH_SET, 6, 10),
+	    [F_IPRECH_SET] = REG_FIELD(IPRECH_SET, 6, 10),
+	    [F_ICHG_SET] = REG_FIELD(ICHG_SET, 6, 13),
+	    [F_ITERM_SET] = REG_FIELD(ITERM_SET, 6, 10),
+	    [F_VPRECHG_TH_SET] = REG_FIELD(VPRECHG_TH_SET, 6, 14),
+	    [F_VRBOOST_SET] = REG_FIELD(VRBOOST_SET, 6, 14),
+	    [F_VFASTCHG_REG_SET1] = REG_FIELD(VFASTCHG_REG_SET1, 4, 14),
+	    [F_VFASTCHG_REG_SET2] = REG_FIELD(VFASTCHG_REG_SET2, 4, 14),
+	    [F_VFASTCHG_REG_SET3] = REG_FIELD(VFASTCHG_REG_SET3, 4, 14),
+	    [F_VRECHG_SET] = REG_FIELD(VRECHG_SET, 4, 14),
+	    [F_VBATOVP_SET] = REG_FIELD(VBATOVP_SET, 4, 14),
+	    [F_IBATM_SHORT_SET] = REG_FIELD(IBATSHORT_SET, 0, 14),
+	    [F_PROCHOT_DG_SET] = REG_FIELD(PROCHOT_CTRL_SET, 14, 15),
+	    [F_PROCHOT_ICRIT_DG_SET] = REG_FIELD(PROCHOT_CTRL_SET, 10, 11),
+	    [F_PROCHOT_IDCHG_DG_SET] = REG_FIELD(PROCHOT_CTRL_SET, 8, 9),
+	    [F_PROCHOT_EN] = REG_FIELD(PROCHOT_CTRL_SET, 0, 4),
+	    [F_PROCHOT_ICRIT_SET] = REG_FIELD(PROCHOT_ICRIT_SET, 0, 14),
+	    [F_PROCHOT_INORM_SET] = REG_FIELD(PROCHOT_INORM_SET, 0, 14),
+	    [F_PROCHOT_IDCHG_SET] = REG_FIELD(PROCHOT_IDCHG_SET, 0, 14),
+	    [F_PROCHOT_VSYS_SET] = REG_FIELD(PROCHOT_VSYS_SET, 0, 14),
+	    [F_IMON_INSEL] = REG_FIELD(PMON_IOUT_CTRL_SET, 9, 9),
+	    [F_PMON_INSEL] = REG_FIELD(PMON_IOUT_CTRL_SET, 8, 8),
+	    [F_IOUT_OUT_EN] = REG_FIELD(PMON_IOUT_CTRL_SET, 7, 7),
+	    [F_IOUT_SOURCE_SEL] = REG_FIELD(PMON_IOUT_CTRL_SET, 6, 6),
+	    [F_IOUT_GAIN_SET] = REG_FIELD(PMON_IOUT_CTRL_SET, 4, 5),
+	    [F_PMON_OUT_EN] = REG_FIELD(PMON_IOUT_CTRL_SET, 3, 3),
+	    [F_PMON_GAIN_SET] = REG_FIELD(PMON_IOUT_CTRL_SET, 0, 2),
+	    [F_PMON_DACIN_VAL] = REG_FIELD(PMON_DACIN_VAL, 0, 9),
+	    [F_IOUT_DACIN_VAL] = REG_FIELD(IOUT_DACIN_VAL, 0, 11),
+	    [F_VCC_BCSRETRY] = REG_FIELD(VCC_UCD_SET, 12, 12),
+	    [F_VCC_ADCRTRY] = REG_FIELD(VCC_UCD_SET, 8, 8),
+	    [F_VCC_USBDETEN] = REG_FIELD(VCC_UCD_SET, 7, 7),
+	    [F_VCC_IDRDETEN] = REG_FIELD(VCC_UCD_SET, 6, 6),
+	    [F_VCC_ENUMRDY] = REG_FIELD(VCC_UCD_SET, 5, 5),
+	    [F_VCC_ADCPOLEN] = REG_FIELD(VCC_UCD_SET, 4, 4),
+	    [F_VCC_DCDMODE] = REG_FIELD(VCC_UCD_SET, 3, 3),
+	    [F_VCC_USB_SW_EN] = REG_FIELD(VCC_UCD_SET, 1, 1),
+	    [F_VCC_USB_SW] = REG_FIELD(VCC_UCD_SET, 0, 0),
+	    [F_VCC_DCDFAIL] = REG_FIELD(VCC_UCD_STATUS, 15, 15),
+	    [F_VCC_CHGPORT] = REG_FIELD(VCC_UCD_STATUS, 12, 13),
+	    [F_VCC_PUPDET] = REG_FIELD(VCC_UCD_STATUS, 11, 11),
+	    [F_VCC_VBUS_VLD] = REG_FIELD(VCC_UCD_STATUS, 7, 7),
+	    [F_VCC_CHGDET] = REG_FIELD(VCC_UCD_STATUS, 6, 6),
+	    [F_VCC_OTGDET] = REG_FIELD(VCC_UCD_STATUS, 3, 3),
+	    [F_VCC_VBINOP] = REG_FIELD(VCC_IDD_STATUS, 6, 6),
+	    [F_VCC_EXTID] = REG_FIELD(VCC_IDD_STATUS, 5, 5),
+	    [F_VCC_IDRDET] = REG_FIELD(VCC_IDD_STATUS, 4, 4),
+	    [F_VCC_INDO] = REG_FIELD(VCC_IDD_STATUS, 0, 3),
+	    [F_VCC_UCDSWEN] = REG_FIELD(VCC_UCD_FCTRL_SET, 10, 10),
+	    [F_VCC_RREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 9, 9),
+	    [F_VCC_DPPU_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 8, 8),
+	    [F_VCC_DPREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 7, 7),
+	    [F_VCC_DMREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 6, 6),
+	    [F_VCC_DPDET_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 5, 5),
+	    [F_VCC_DMDET_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 4, 4),
+	    [F_VCC_DPSINK_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 3, 3),
+	    [F_VCC_DMSINK_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 2, 2),
+	    [F_VCC_DP_BUFF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 1, 1),
+	    [F_VCC_DM_BUFF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 0, 0),
+	    [F_VCC_EXTCLKENBL] = REG_FIELD(VCC_UCD_FCTRL_EN, 15, 15),
+	    [F_VCC_PLSTESTEN] = REG_FIELD(VCC_UCD_FCTRL_EN, 14, 14),
+	    [F_VCC_UCDSWEN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 10, 10),
+	    [F_VCC_RREF_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 9, 9),
+	    [F_VCC_DPPU_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 8, 8),
+	    [F_VCC_DPREF_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 7, 7),
+	    [F_VCC_DMREF_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 6, 6),
+	    [F_VCC_DPDET_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 5, 5),
+	    [F_VCC_DMDET_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 4, 4),
+	    [F_VCC_DPSINK_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 3, 3),
+	    [F_VCC_DMSINK_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 2, 2),
+	    [F_VCC_DP_BUFF_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 1, 1),
+	    [F_VCC_DM_BUFF_EN_TSTENB] = REG_FIELD(VCC_UCD_FCTRL_EN, 0, 0),
+
+	    [F_VBUS_BCSRETRY] = REG_FIELD(VBUS_UCD_SET, 12, 12),
+	    [F_VBUS_ADCRTRY] = REG_FIELD(VBUS_UCD_SET, 8, 8),
+	    [F_VBUS_USBDETEN] = REG_FIELD(VBUS_UCD_SET, 7, 7),
+	    [F_VBUS_IDRDETEN] = REG_FIELD(VBUS_UCD_SET, 6, 6),
+	    [F_VBUS_ENUMRDY] = REG_FIELD(VBUS_UCD_SET, 5, 5),
+	    [F_VBUS_ADCPOLEN] = REG_FIELD(VBUS_UCD_SET, 4, 4),
+	    [F_VBUS_DCDMODE] = REG_FIELD(VBUS_UCD_SET, 3, 3),
+	    [F_VBUS_USB_SW_EN] = REG_FIELD(VBUS_UCD_SET, 1, 1),
+	    [F_VBUS_USB_SW] = REG_FIELD(VBUS_UCD_SET, 0, 0),
+	    [F_VBUS_DCDFAIL] = REG_FIELD(VBUS_UCD_STATUS, 15, 15),
+	    [F_VBUS_CHGPORT] = REG_FIELD(VBUS_UCD_STATUS, 12, 13),
+	    [F_VBUS_PUPDET] = REG_FIELD(VBUS_UCD_STATUS, 11, 11),
+	    [F_VBUS_VBUS_VLD] = REG_FIELD(VBUS_UCD_STATUS, 7, 7),
+	    [F_VBUS_CHGDET] = REG_FIELD(VBUS_UCD_STATUS, 6, 6),
+	    [F_VBUS_OTGDET] = REG_FIELD(VBUS_UCD_STATUS, 3, 3),
+	    [F_VBUS_VBINOP] = REG_FIELD(VBUS_IDD_STATUS, 6, 6),
+	    [F_VBUS_EXTID] = REG_FIELD(VBUS_IDD_STATUS, 5, 5),
+	    [F_VBUS_IDRDET] = REG_FIELD(VBUS_IDD_STATUS, 4, 4),
+	    [F_VBUS_INDO] = REG_FIELD(VBUS_IDD_STATUS, 0, 3),
+	    [F_VBUS_UCDSWEN] = REG_FIELD(VCC_UCD_FCTRL_SET, 10, 10),
+	    [F_VBUS_RREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 9, 9),
+	    [F_VBUS_DPPU_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 8, 8),
+	    [F_VBUS_DPREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 7, 7),
+	    [F_VBUS_DMREF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 6, 6),
+	    [F_VBUS_DPDET_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 5, 5),
+	    [F_VBUS_DMDET_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 4, 4),
+	    [F_VBUS_DPSINK_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 3, 3),
+	    [F_VBUS_DMSINK_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 2, 2),
+	    [F_VBUS_DP_BUFF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 1, 1),
+	    [F_VBUS_DM_BUFF_EN] = REG_FIELD(VCC_UCD_FCTRL_SET, 0, 0),
+
+	    [F_VBUS_EXTCLKENBL] = REG_FIELD(VBUS_UCD_FCTRL_EN, 15, 15),
+	    [F_VBUS_PLSTESTEN] = REG_FIELD(VBUS_UCD_FCTRL_EN, 14, 14),
+	    [F_VBUS_UCDSWEN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 10, 10),
+	    [F_VBUS_RREF_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 9, 9),
+	    [F_VBUS_DPPU_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 8, 8),
+	    [F_VBUS_DPREF_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 7, 7),
+	    [F_VBUS_DMREF_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 6, 6),
+	    [F_VBUS_DPDET_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 5, 5),
+	    [F_VBUS_DMDET_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 4, 4),
+	    [F_VBUS_DPSINK_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 3, 3),
+	    [F_VBUS_DMSINK_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 2, 2),
+	    [F_VBUS_DP_BUFF_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 1, 1),
+	    [F_VBUS_DM_BUFF_EN_TSTENB] = REG_FIELD(VBUS_UCD_FCTRL_EN, 0, 0),
+
+	    [F_CHIP_ID] = REG_FIELD(CHIP_ID, 0, 15),
+	    [F_CHIP_REV] = REG_FIELD(CHIP_REV, 0, 15),
+	    [F_ONE_CELL_MODE] = REG_FIELD(IC_SET1, 11, 11),
+	    [F_cell] = REG_FIELD(IC_SET1, 1, 1),
+	    [F_VACP_AUTO_DISCHG] = REG_FIELD(IC_SET1, 9, 9),
+	    [F_VACP_LOAD] = REG_FIELD(IC_SET1, 8, 8),
+	    [F_ACOK_POL] = REG_FIELD(IC_SET1, 1, 1),
+	    [F_ACOK_DISEN] = REG_FIELD(IC_SET1, 0, 0),
+	    [F_DEBUG_SET1] = REG_FIELD(IC_SET2, 4, 8),
+	    [F_DEBUG_SET0] = REG_FIELD(IC_SET2, 0, 0),
+	    [F_MONRST_STATE] = REG_FIELD(SYSTEM_STATUS, 6, 6),
+	    [F_ALMRST_STATE] = REG_FIELD(SYSTEM_STATUS, 5, 5),
+	    [F_CHGRST_STATE] = REG_FIELD(SYSTEM_STATUS, 4, 4),
+	    [F_OTPLD_STATE] = REG_FIELD(SYSTEM_STATUS, 1, 1),
+	    [F_ALLRST_STATE] = REG_FIELD(SYSTEM_STATUS, 0, 0),
+	    [F_PROTECT_SET] = REG_FIELD(PROTECT_SET, 0, 15),
+	    [F_MAP_SET] = REG_FIELD(MAP_SET, 0, 15),
+	    [F_ADCINTERVAL] = REG_FIELD(VM_CTRL_SET, 14, 15),
+	    [F_ADCMOD] = REG_FIELD(VM_CTRL_SET, 12, 13),
+	    [F_ADCTMOD] = REG_FIELD(VM_CTRL_SET, 10, 11),
+	    [F_EXTIADPEN] = REG_FIELD(VM_CTRL_SET, 9, 9),
+	    [F_VSYSENB] = REG_FIELD(VM_CTRL_SET, 8, 8),
+	    [F_VCCENB] = REG_FIELD(VM_CTRL_SET, 7, 7),
+	    [F_VBUSENB] = REG_FIELD(VM_CTRL_SET, 6, 6),
+	    [F_VACPENB] = REG_FIELD(VM_CTRL_SET, 5, 5),
+	    [F_IACPENB] = REG_FIELD(VM_CTRL_SET, 4, 4),
+	    [F_THERMENB] = REG_FIELD(VM_CTRL_SET, 3, 3),
+	    [F_VBATENB] = REG_FIELD(VM_CTRL_SET, 2, 2),
+	    [F_IBATMENB] = REG_FIELD(VM_CTRL_SET, 1, 1),
+	    [F_IBATPENB] = REG_FIELD(VM_CTRL_SET, 0, 0),
+	    [F_TMPTHR1B] = REG_FIELD(THERM_WINDOW_SET1, 8, 15),
+	    [F_TMPTHR1A] = REG_FIELD(THERM_WINDOW_SET1, 0, 7),
+	    [F_TMPTHR2B] = REG_FIELD(THERM_WINDOW_SET2, 8, 15),
+	    [F_TMPTHR2A] = REG_FIELD(THERM_WINDOW_SET2, 0, 7),
+	    [F_TMPTHR3B] = REG_FIELD(THERM_WINDOW_SET3, 8, 15),
+	    [F_TMPTHR3A] = REG_FIELD(THERM_WINDOW_SET3, 0, 7),
+	    [F_TMPTHR4B] = REG_FIELD(THERM_WINDOW_SET4, 8, 15),
+	    [F_TMPTHR4A] = REG_FIELD(THERM_WINDOW_SET4, 0, 7),
+	    [F_TMPTHR5B] = REG_FIELD(THERM_WINDOW_SET5, 8, 15),
+	    [F_TMPTHR5A] = REG_FIELD(THERM_WINDOW_SET5, 0, 7),
+	    [F_IBATP_TH_SET] = REG_FIELD(IBATP_TH_SET, 0, 14),
+	    [F_IBATM_TH_SET] = REG_FIELD(IBATM_TH_SET, 0, 14),
+	    [F_VBAT_TH_SET] = REG_FIELD(VBAT_TH_SET, 0, 14),
+	    [F_THERM_TH_SET] = REG_FIELD(THERM_TH_SET, 0, 7),
+	    [F_IACP_TH_SET] = REG_FIELD(IACP_TH_SET, 0, 14),
+	    [F_VACP_TH_SET] = REG_FIELD(VACP_TH_SET, 0, 14),
+	    [F_VBUS_TH_SET] = REG_FIELD(VBUS_TH_SET, 0, 14),
+	    [F_VCC_TH_SET] = REG_FIELD(VCC_TH_SET, 0, 14),
+	    [F_VSYS_TH_SET] = REG_FIELD(VSYS_TH_SET, 0, 14),
+	    [F_EXTIADP_TH_SET] = REG_FIELD(EXTIADP_TH_SET, 0, 11),
+	    [F_IBATP_VAL] = REG_FIELD(IBATP_VAL, 0, 14),
+	    [F_IBATP_AVE_VAL] = REG_FIELD(IBATP_AVE_VAL, 0, 14),
+	    [F_IBATM_VAL] = REG_FIELD(IBATM_VAL, 0, 14),
+	    [F_IBATM_AVE_VAL] = REG_FIELD(IBATM_AVE_VAL, 0, 14),
+	    [F_VBAT_VAL] = REG_FIELD(VBAT_VAL, 0, 14),
+	    [F_VBAT_AVE_VAL] = REG_FIELD(VBAT_AVE_VAL, 0, 14),
+	    [F_THERM_VAL] = REG_FIELD(THERM_VAL, 0, 7),
+	    [F_VTH_VAL] = REG_FIELD(VTH_VAL, 0, 11),
+	    [F_IACP_VAL] = REG_FIELD(IACP_VAL, 0, 14),
+	    [F_IACP_AVE_VAL] = REG_FIELD(IACP_AVE_VAL, 0, 14),
+	    [F_VACP_VAL] = REG_FIELD(VACP_VAL, 0, 14),
+	    [F_VACP_AVE_VAL] = REG_FIELD(VACP_AVE_VAL, 0, 14),
+	    [F_VBUS_VAL] = REG_FIELD(VBUS_VAL, 0, 14),
+	    [F_VBUS_AVE_VAL] = REG_FIELD(VBUS_AVE_VAL, 0, 14),
+	    [F_VCC_VAL] = REG_FIELD(VCC_VAL, 0, 14),
+	    [F_VCC_AVE_VAL] = REG_FIELD(VCC_AVE_VAL, 0, 14),
+	    [F_VSYS_VAL] = REG_FIELD(VSYS_VAL, 0, 14),
+	    [F_VSYS_AVE_VAL] = REG_FIELD(VSYS_AVE_VAL, 0, 14),
+	    [F_EXTIADP_VAL] = REG_FIELD(EXTIADP_VAL, 0, 11),
+	    [F_EXTIADP_AVE_VAL] = REG_FIELD(EXTIADP_AVE_VAL, 0, 11),
+	    [F_VACPCLPS_TH_SET] = REG_FIELD(VACPCLPS_TH_SET, 7, 14),
+	    [F_INT7_SET] = REG_FIELD(INT7_SET, 0, 15),
+	    [F_INT6_SET] = REG_FIELD(INT6_SET, 0, 13),
+	    [F_INT5_SET] = REG_FIELD(INT5_SET, 0, 13),
+	    [F_INT4_SET] = REG_FIELD(INT4_SET, 0, 9),
+	    [F_INT3_SET] = REG_FIELD(INT3_SET, 0, 15),
+	    [F_INT2_SET] = REG_FIELD(INT2_SET, 0, 15),
+	    [F_INT1_SET] = REG_FIELD(INT1_SET, 0, 15),
+	    [F_INT0_SET] = REG_FIELD(INT0_SET, 0, 7),
+	    [F_VBUS_RBUV_DET] = REG_FIELD(INT1_SET, 15, 15),
+	    [F_VBUS_RBUV_RES] = REG_FIELD(INT1_SET, 14, 14),
+	    [F_VBUS_TH_DET] = REG_FIELD(INT1_SET, 9, 9),
+	    [F_VBUS_TH_RES] = REG_FIELD(INT1_SET, 8, 8),
+	    [F_VBUS_IIN_MOD] = REG_FIELD(INT1_SET, 6, 6),
+	    [F_VBUS_OV_DET] = REG_FIELD(INT1_SET, 5, 5),
+	    [F_VBUS_OV_RES] = REG_FIELD(INT1_SET, 4, 4),
+	    [F_VBUS_CLPS_DET] = REG_FIELD(INT1_SET, 3, 3),
+	    [F_VBUS_CLPS] = REG_FIELD(INT1_SET, 2, 2),
+	    [F_VBUS_DET] = REG_FIELD(INT1_SET, 1, 1),
+	    [F_VBUS_RES] = REG_FIELD(INT1_SET, 0, 0),
+	    [F_VCC_RBUV_DET] = REG_FIELD(INT2_SET, 15, 15),
+	    [F_VCC_RBUV_RES] = REG_FIELD(INT2_SET, 14, 14),
+	    [F_VCC_TH_DET] = REG_FIELD(INT2_SET, 9, 9),
+	    [F_VCC_TH_RES] = REG_FIELD(INT2_SET, 8, 8),
+	    [F_VCC_IIN_MOD] = REG_FIELD(INT2_SET, 6, 6),
+	    [F_VCC_OVP_DET] = REG_FIELD(INT2_SET, 5, 5),
+	    [F_VCC_OVP_RES] = REG_FIELD(INT2_SET, 4, 4),
+	    [F_VCC_CLPS_DET] = REG_FIELD(INT2_SET, 3, 3),
+	    [F_VCC_CLPS_RES] = REG_FIELD(INT2_SET, 2, 2),
+	    [F_VCC_DET] = REG_FIELD(INT2_SET, 1, 1),
+	    [F_VCC_RES] = REG_FIELD(INT2_SET, 0, 0),
+	    [F_TH_DET] = REG_FIELD(INT3_SET, 15, 15),
+	    [F_TH_RMV] = REG_FIELD(INT3_SET, 14, 14),
+	    [F_TMP_OUT_DET] = REG_FIELD(INT3_SET, 11, 11),
+	    [F_TMP_OUT_RES] = REG_FIELD(INT3_SET, 10, 10),
+	    [F_VBAT_TH_DET] = REG_FIELD(INT3_SET, 9, 9),
+	    [F_VBAT_TH_RES] = REG_FIELD(INT3_SET, 8, 8),
+	    [F_IBAT_SHORT_DET] = REG_FIELD(INT3_SET, 7, 7),
+	    [F_IBAT_SHORT_RES] = REG_FIELD(INT3_SET, 6, 6),
+	    [F_VBAT_OV_DET] = REG_FIELD(INT3_SET, 5, 5),
+	    [F_VBAT_OV_RES] = REG_FIELD(INT3_SET, 4, 4),
+	    [F_BAT_ASSIST_DET] = REG_FIELD(INT3_SET, 3, 3),
+	    [F_BAT_ASSIST_RES] = REG_FIELD(INT3_SET, 2, 2),
+	    [F_VSYS_TH_DET] = REG_FIELD(INT4_SET, 9, 9),
+	    [F_VSYS_TH_RES] = REG_FIELD(INT4_SET, 8, 8),
+	    [F_VSYS_OV_DET] = REG_FIELD(INT4_SET, 5, 5),
+	    [F_VSYS_OV_RES] = REG_FIELD(INT4_SET, 4, 4),
+	    [F_VSYS_SHT_DET] = REG_FIELD(INT4_SET, 3, 3),
+	    [F_VSYS_SHT_RES] = REG_FIELD(INT4_SET, 2, 2),
+	    [F_VSYS_UV_DET] = REG_FIELD(INT4_SET, 1, 1),
+	    [F_VSYS_UV_RES] = REG_FIELD(INT4_SET, 0, 0),
+	    [F_OTP_LOAD_DONE] = REG_FIELD(INT5_SET, 13, 13),
+	    [F_PWR_ON] = REG_FIELD(INT5_SET, 12, 12),
+	    [F_EXTIADP_TRNS] = REG_FIELD(INT5_SET, 11, 11),
+	    [F_EXTIADP_TH_DET] = REG_FIELD(INT5_SET, 9, 9),
+	    [F_EXIADP_TH_RES] = REG_FIELD(INT5_SET, 8, 8),
+	    [F_BAT_MNT_DET] = REG_FIELD(INT5_SET, 7, 7),
+	    [F_BAT_MNT_RES] = REG_FIELD(INT5_SET, 6, 6),
+	    [F_TSD_DET] = REG_FIELD(INT5_SET, 5, 5),
+	    [F_TSD_RES] = REG_FIELD(INT5_SET, 4, 4),
+	    [F_CHGWDT_EXP] = REG_FIELD(INT5_SET, 3, 3),
+	    [F_THERMWDT_EXP] = REG_FIELD(INT5_SET, 2, 2),
+	    [F_TMP_TRNS] = REG_FIELD(INT5_SET, 1, 1),
+	    [F_CHG_TRNS] = REG_FIELD(INT5_SET, 0, 0),
+	    [F_VBUS_UCD_PORT_DET] = REG_FIELD(INT6_SET, 13, 13),
+	    [F_VBUS_UCD_UCHG_DET] = REG_FIELD(INT6_SET, 12, 12),
+	    [F_VBUS_UCD_URID_RMV] = REG_FIELD(INT6_SET, 11, 11),
+	    [F_VBUS_UCD_OTG_DET] = REG_FIELD(INT6_SET, 10, 10),
+	    [F_VBUS_UCD_URID_MOD] = REG_FIELD(INT6_SET, 8, 8),
+	    [F_VCC_UCD_PORT_DET] = REG_FIELD(INT6_SET, 5, 5),
+	    [F_VCC_UCD_UCHG_DET] = REG_FIELD(INT6_SET, 4, 4),
+	    [F_VCC_UCD_URID_RMV] = REG_FIELD(INT6_SET, 3, 3),
+	    [F_VCC_UCD_OTG_DET] = REG_FIELD(INT6_SET, 2, 2),
+	    [F_VCC_UCD_URID_MOD] = REG_FIELD(INT6_SET, 0, 0),
+	    [F_PROCHOT_DET] = REG_FIELD(INT7_SET, 15, 15),
+	    [F_PROCHOT_RES] = REG_FIELD(INT7_SET, 14, 14),
+	    [F_VACP_DET] = REG_FIELD(INT7_SET, 11, 11),
+	    [F_VACP_RES] = REG_FIELD(INT7_SET, 10, 10),
+	    [F_VACP_TH_DET] = REG_FIELD(INT7_SET, 9, 9),
+	    [F_VACP_TH_RES] = REG_FIELD(INT7_SET, 8, 8),
+	    [F_IACP_TH_DET] = REG_FIELD(INT7_SET, 7, 7),
+	    [F_IACP_THE_RES] = REG_FIELD(INT7_SET, 6, 6),
+	    [F_THERM_TH_DET] = REG_FIELD(INT7_SET, 5, 5),
+	    [F_THERM_TH_RES] = REG_FIELD(INT7_SET, 4, 4),
+	    [F_IBATM_TH_DET] = REG_FIELD(INT7_SET, 3, 3),
+	    [F_IBATM_TH_RES] = REG_FIELD(INT7_SET, 2, 2),
+	    [F_IBATP_TH_DET] = REG_FIELD(INT7_SET, 1, 1),
+	    [F_IBATP_TH_RES] = REG_FIELD(INT7_SET, 0, 0),
+	    [F_INT7_STATUS] = REG_FIELD(INT7_STATUS, 0, 15),
+	    [F_INT6_STATUS] = REG_FIELD(INT6_STATUS, 0, 13),
+	    [F_INT5_STATUS] = REG_FIELD(INT5_STATUS, 0, 13),
+	    [F_INT4_STATUS] = REG_FIELD(INT4_STATUS, 0, 9),
+	    [F_INT3_STATUS] = REG_FIELD(INT3_STATUS, 0, 15),
+	    [F_INT2_STATUS] = REG_FIELD(INT2_STATUS, 0, 15),
+	    [F_INT1_STATUS] = REG_FIELD(INT1_STATUS, 0, 15),
+	    [F_INT0_STATUS] = REG_FIELD(INT0_STATUS, 0, 7),
+	    [F_ILIM_DECREASE] = REG_FIELD(OTPREG0, 0, 15),
+	    [F_RESERVE_OTPREG1] = REG_FIELD(OTPREG1, 0, 15),
+	    [F_POWER_SAVE_MODE] = REG_FIELD(SMBREG, 0, 15),
+	    [F_DEBUG_MODE_SET] = REG_FIELD(DEBUG_MODE_SET, 0, 15),
+	    [F_DEBUG0x14] = REG_FIELD(DEBUG0x14, 0, 15),
+	    [F_DEBUG0x1A] = REG_FIELD(DEBUG0x1A, 0, 15),
+};
+
+/* CHGSTM_STATEs */
+#define CHGSTM_SUSPEND 0x00
+#define CHGSTM_TRICKLE_CHARGE 0x01
+#define CHGSTM_PRE_CHARGE 0x02
+#define CHGSTM_FAST_CHARGE 0x03
+#define CHGSTM_TOP_OFF 0x04
+#define CHGSTM_DONE 0x05
+#define CHGSTM_OTG 0x08
+#define CHGSTM_OTG_DONE 0x09
+#define CHGSTM_TEMPERATURE_ERROR_1 0x10
+#define CHGSTM_TEMPERATURE_ERROR_2 0x11
+#define CHGSTM_TEMPERATURE_ERROR_3 0x12
+#define CHGSTM_TEMPERATURE_ERROR_4 0x13
+#define CHGSTM_TEMPERATURE_ERROR_5 0x14
+#define CHGSTM_TEMPERATURE_ERROR_6 0x15
+#define CHGSTM_TEMPERATURE_ERROR_7 0x18
+#define CHGSTM_THERMAL_SHUT_DOWN_1 0x20
+#define CHGSTM_THERMAL_SHUT_DOWN_2 0x21
+#define CHGSTM_THERMAL_SHUT_DOWN_3 0x22
+#define CHGSTM_THERMAL_SHUT_DOWN_4 0x23
+#define CHGSTM_THERMAL_SHUT_DOWN_5 0x24
+#define CHGSTM_THERMAL_SHUT_DOWN_6 0x25
+#define CHGSTM_THERMAL_SHUT_DOWN_7 0x28
+#define CHGSTM_BATTERY_ERROR 0x40
+
+/* VBAT_VSYS_STATUS */
+#define STATUS_VSYS_OV BIT(15)
+#define STATUS_VSYS_SSD BIT(14)
+#define STATUS_VSYS_SCP BIT(13)
+#define STATUS_VSYS_UVN BIT(12)
+#define STATUS_IBAT_SHORT BIT(6)
+#define STATUS_VBAT_OV BIT(3)
+#define STATUS_DEAD_BAT BIT(0)
+
+/* VBUS_VCC_STATUS */
+#define STATUS_VACP_DET BIT(12)
+#define STATUS_VCC_OVP BIT(11)
+#define STATUS_ILIM_VCC_MOD BIT(10)
+#define STATUS_VCC_CLPS BIT(9)
+#define STATUS_VCC_DET BIT(8)
+#define STATUS_VBUS_OVP BIT(3)
+#define STATUS_ILIM_VBUS_MOD BIT(2)
+#define STATUS_VBUS_CLPS BIT(1)
+#define STATUS_VBUS_DET BIT(0)
+
+/* Interrupt set/status definitions */
+
+/* INT 0 */
+#define INT0_INT7_STATUS BIT(7)
+#define INT0_INT6_STATUS BIT(6)
+#define INT0_INT5_STATUS BIT(5)
+#define INT0_INT4_STATUS BIT(4)
+#define INT0_INT3_STATUS BIT(3)
+#define INT0_INT2_STATUS BIT(2)
+#define INT0_INT1_STATUS BIT(1)
+#define INT0_INT0_STATUS BIT(0)
+#define INT0_ALL 0xff
+
+/* INT 1 */
+#define VBUS_RBUV_DET BIT(15)
+#define VBUS_RBUV_RES BIT(14)
+#define VBUS_TH_DET BIT(9)
+#define VBUS_TH_RES BIT(8)
+#define VBUS_IIN_MOD BIT(6)
+#define VBUS_OV_DET BIT(5)
+#define VBUS_OV_RES BIT(4)
+#define VBUS_CLPS_DET BIT(3)
+#define VBUS_CLPS BIT(2)
+#define VBUS_DET BIT(1)
+#define VBUS_RES BIT(0)
+#define INT1_ALL (VBUS_RBUV_DET|\
+		 VBUS_RBUV_RES|\
+		 VBUS_TH_DET |\
+		 VBUS_TH_RES |\
+		 VBUS_IIN_MOD|\
+		 VBUS_OV_DET |\
+		 VBUS_OV_RES |\
+		 VBUS_CLPS_DET |\
+		 VBUS_CLPS |\
+		 VBUS_DET |\
+		 VBUS_RES)
+
+/* INT 2 */
+#define VCC_RBUV_DET BIT(15)
+#define VCC_RBUV_RES BIT(14)
+#define VCC_TH_DET BIT(9)
+#define VCC_TH_RES BIT(8)
+#define VCC_IIN_MOD BIT(6)
+#define VCC_OVP_DET BIT(5)
+#define VCC_OVP_RES BIT(4)
+#define VCC_CLPS_DET BIT(3)
+#define VCC_CLPS_RES BIT(2)
+#define VCC_DET BIT(1)
+#define VCC_RES BIT(0)
+#define INT2_ALL (VCC_RBUV_DET |\
+		 VCC_RBUV_RES |\
+		 VCC_TH_DET |\
+		 VCC_TH_RES |\
+		 VCC_IIN_MOD |\
+		 VCC_OVP_DET |\
+		 VCC_OVP_RES |\
+		 VCC_CLPS_DET |\
+		 VCC_CLPS_RES |\
+		 VCC_DET |\
+		 VCC_RES)
+/* INT 3 */
+#define TH_DET BIT(15)
+#define TH_RMV BIT(14)
+#define TMP_OUT_DET BIT(11)
+#define TMP_OUT_RES BIT(10)
+#define VBAT_TH_DET BIT(9)
+#define VBAT_TH_RES BIT(8)
+#define IBAT_SHORT_DET BIT(7)
+#define IBAT_SHORT_RES BIT(6)
+#define VBAT_OV_DET BIT(5)
+#define VBAT_OV_RES BIT(4)
+#define BAT_ASSIST_DET BIT(3)
+#define BAT_ASSIST_RES BIT(2)
+#define INT3_ALL (TH_DET |\
+		 TH_RMV |\
+		 TMP_OUT_DET |\
+		 TMP_OUT_RES |\
+		 VBAT_TH_DET |\
+		 VBAT_TH_RES |\
+		 IBAT_SHORT_DET |\
+		 IBAT_SHORT_RES |\
+		 VBAT_OV_DET |\
+		 VBAT_OV_RES |\
+		 BAT_ASSIST_DET |\
+		 BAT_ASSIST_RES)
+
+/* INT 4 */
+#define VSYS_TH_DET BIT(9)
+#define VSYS_TH_RES BIT(8)
+#define VSYS_OV_DET BIT(5)
+#define VSYS_OV_RES BIT(4)
+#define VSYS_SHT_DET BIT(3)
+#define VSYS_SHT_RES BIT(2)
+#define VSYS_UV_DET BIT(1)
+#define VSYS_UV_RES BIT(0)
+#define INT4_ALL (VSYS_TH_DET |\
+		 VSYS_TH_RES |\
+		 VSYS_OV_DET |\
+		 VSYS_OV_RES |\
+		 VSYS_SHT_DET |\
+		 VSYS_SHT_RES |\
+		 VSYS_UV_DET |\
+		 VSYS_UV_RES)
+
+/* INT 5*/
+#define OTP_LOAD_DONE BIT(13)
+#define PWR_ON BIT(12)
+#define EXTIADP_TRNS BIT(11)
+#define EXTIADP_TH_DET BIT(9)
+#define EXIADP_TH_RES BIT(8)
+#define BAT_MNT_DET BIT(7)
+#define BAT_MNT_RES BIT(6)
+#define TSD_DET BIT(5)
+#define TSD_RES BIT(4)
+#define CHGWDT_EXP BIT(3)
+#define THERMWDT_EXP BIT(2)
+#define TMP_TRNS BIT(1)
+#define CHG_TRNS BIT(0)
+#define INT5_ALL (OTP_LOAD_DONE |\
+		 PWR_ON |\
+		 EXTIADP_TRNS |\
+		 EXTIADP_TH_DET |\
+		 EXIADP_TH_RES |\
+		 BAT_MNT_DET |\
+		 BAT_MNT_RES |\
+		 TSD_DET |\
+		 TSD_RES |\
+		 CHGWDT_EXP |\
+		 THERMWDT_EXP |\
+		 TMP_TRNS |\
+		 CHG_TRNS)
+
+/* INT 6*/
+#define VBUS_UCD_PORT_DET BIT(13)
+#define VBUS_UCD_UCHG_DET BIT(12)
+#define VBUS_UCD_URID_RMV BIT(11)
+#define VBUS_UCD_OTG_DET BIT(10)
+#define VBUS_UCD_URID_MOD BIT(8)
+#define VCC_UCD_PORT_DET BIT(5)
+#define VCC_UCD_UCHG_DET BIT(4)
+#define VCC_UCD_URID_RMV BIT(3)
+#define VCC_UCD_OTG_DET BIT(2)
+#define VCC_UCD_URID_MOD BIT(0)
+#define INT6_ALL (VBUS_UCD_PORT_DET |\
+		 VBUS_UCD_UCHG_DET |\
+		 VBUS_UCD_URID_RMV |\
+		 VBUS_UCD_OTG_DET |\
+		 VBUS_UCD_URID_MOD |\
+		 VCC_UCD_PORT_DET |\
+		 VCC_UCD_UCHG_DET |\
+		 VCC_UCD_URID_RMV |\
+		 VCC_UCD_OTG_DET |\
+		 VCC_UCD_URID_MOD)
+
+/* INT 7 */
+#define PROCHOT_DET BIT(15)
+#define PROCHOT_RES BIT(14)
+#define VACP_DET BIT(11)
+#define VACP_RES BIT(10)
+#define VACP_TH_DET BIT(9)
+#define VACP_TH_RES BIT(8)
+#define IACP_TH_DET BIT(7)
+#define IACP_THE_RES BIT(6)
+#define THERM_TH_DET BIT(5)
+#define THERM_TH_RES BIT(4)
+#define IBATM_TH_DET BIT(3)
+#define IBATM_TH_RES BIT(2)
+#define IBATP_TH_DET BIT(1)
+#define IBATP_TH_RES BIT(0)
+#define INT7_ALL (PROCHOT_DET |\
+		 PROCHOT_RES |\
+		 VACP_DET |\
+		 VACP_RES |\
+		 VACP_TH_DET |\
+		 VACP_TH_RES |\
+		 IACP_TH_DET |\
+		 IACP_THE_RES |\
+		 THERM_TH_DET |\
+		 THERM_TH_RES |\
+		 IBATM_TH_DET |\
+		 IBATM_TH_RES |\
+		 IBATP_TH_DET |\
+		 IBATP_TH_RES)
+
+/* SYSTEM_CTRL_SET*/
+#define MONRST BIT(6)
+#define ALMRST BIT(5)
+#define CHGRST BIT(4)
+#define OTPLD  BIT(1)
+#define ALLRST BIT(0)
+
+/* F_BATTEMP */
+#define ROOM		0x0
+#define HOT1		0x1
+#define HOT2		0x2
+#define HOT3		0x3
+#define COLD1		0x4
+#define COLD2		0x5
+#define TEMP_DIS	0x6
+#define BATT_OPEN	0x7
+
+#endif
-- 
2.21.0


-- 
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =] 




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux