RE: [PATCH 0/9] remoteproc: imx_rproc: support i.MX8/8M/7ULP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> Subject: Re: [PATCH 0/9] remoteproc: imx_rproc: support i.MX8/8M/7ULP
> 
> On Wed, 19 Feb 2020 at 18:36, Peng Fan <peng.fan@xxxxxxx> wrote:
> >
> > Hi Mathieu,
> >
> > > Subject: Re: [PATCH 0/9] remoteproc: imx_rproc: support
> > > i.MX8/8M/7ULP
> > >
> > > Hi Peng,
> > >
> > > On Wed, 19 Feb 2020 at 00:33, <peng.fan@xxxxxxx> wrote:
> > > >
> > > > From: Peng Fan <peng.fan@xxxxxxx>
> > > >
> > > > This patchset aim to replace NXP vendor imx_rpmsg.c driver.
> > >
> > > You mean remoteproc/imx_rproc.c ?  Upstream rpmsg/imx_rpmsg.c
> > > doesn't exist.
> >
> > imx_rpmsg.c only in NXP vendor tree. This pachset is to use
> > imx_rproc.c for rpmsg/virtio functions for i.MX SoC.
> >
> > >
> > > >
> > > > This patchset is tested with Loic PALLARDY's patch
> > > > "remoteproc: add support for co-processor loaded and booted before
> > > kernel"
> > > > https://eur01.safelinks.protection.outlook.com/?url=https%3A%2F%2F
> > > > patc
> > > >
> > >
> hwork.kernel.org%2Fpatch%2F11265869%2F&amp;data=02%7C01%7Cpeng.f
> > > an%40n
> > > >
> > >
> xp.com%7Ce1cb19e535a14b63d0da08d7b568fd56%7C686ea1d3bc2b4c6fa9
> > > 2cd99c5c
> > > >
> > >
> 301635%7C0%7C0%7C637177334839497832&amp;sdata=aKQ%2Bulco63ba
> > > YT%2BDZDk0
> > > > VLt1NpkNuhrY3ssxiRCOcrM%3D&amp;reserved=0,
> > > > and inspried from st's remoteproc early boot support.
> > > > Since Loic's patch is still under review, just expect your
> > > > comments :)
> > >
> > > Did you base your work on top of Loic's because your MCU firmware is
> > > always loaded by the bootloader?
> >
> > I only took Loic's early-boot patch as base and apply my patchset.
> >
> > The mcu firmware currently only loaded by bootloader or system controller
> firmware.
> > NXP released mcu firmware not support being loaded by Linux remoteproc.
> 
> Thanks for bringing this use case to the front.  I suspected such a scenario
> existed but didn't spend too much time thinking about it since none had been
> brought to our attention. 

Actually to i.MX7ULP, M4 is booted first from hardware design and it
controls every things, A7 is under control of M4

To i.MX8/8X, M4 is booted by system control unit firmware for quick boot
for automotive CAN and Linux is booted later. Linux could only IPC to M4,
and nothing else.

To i.MX8M, M4 is booted by bootloader, but it could also be booted by Linux,
It is just NXP only support bootloader case.

 I will review your patchset and continue the
> conversation with Arnaud with it in mind.  I also invite you to join that
> conversation.

Appreciate.

Thanks,
Peng.

> 
> Regards,
> Mathieu
> 
> >
> >  If not please send another revision of your work
> > > without early boot support.  When we have a clear view on how to
> > > proceed with the early boot support you can send another set to enable
> that.
> >
> > I'll wait your new patch for early boot in remoteproc-core. Then I'll
> > rebase and send a new version. Since I introduce big changes to
> > imx_rproc.c, so I'll see whether any comments there.
> >
> > Thanks,
> > Peng.
> >
> > >
> > > Thanks,
> > > Mathieu
> > >
> > > >
> > > > Patch [1,2]/9: dt-bindings convert to json and new SoC support
> > > > Patch
> > > > 3/9: skip firmware load when recovery. To i.MX8, firmware is not
> > > >            handled by Linux.
> > > >
> > > > Patch [4-9]/9: i.MX specific part to support rpmsg/virtio with mbox.
> > > >       because NXP release image not have resoure table, so add
> resource
> > > >       table in dts
> > > >
> > > > My test dts diff for i.MX8QXP MEK, but I have tested this patchset
> > > > for i.MX8QXP MEK, i.MX8MM EVK, i.MX7ULP EVK:
> > > >
> > > > +
> > > > +       imx8x-cm4 {
> > > > +               compatible = "fsl,imx8qxp-cm4";
> > > > +               rsrc-table = <
> > > > +                       0x1 0x2 0x0 0x0 0x18 0x5c
> > > > +                       3
> > > > +                       /*fw_rsc_vdev*/
> > > > +                       7 0 1 0 0 0x200
> > > > +                       /*fw_rsc_vdev_vring*/
> > > > +                       0x90000000 4096 256 1 0
> > > > +                       0x90008000 4096 256 2 0
> > > > +                       3
> > > > +                       /*fw_rsc_vdev*/
> > > > +                       7 1 1 0 0 0x200
> > > > +                       /*fw_rsc_vdev_vring*/
> > > > +                       0x90010000 4096 256 1 0
> > > > +                       0x90018000 4096 256 2 0
> > > > +               >;
> > > > +               early-booted;
> > > > +               mbox-names = "tx", "rx", "rxdb";
> > > > +               mboxes = <&lsio_mu5 0 1
> > > > +                         &lsio_mu5 1 1
> > > > +                         &lsio_mu5 3 1>;
> > > > +               mub-partition = <3>;
> > > > +               memory-region = <&vdev0vring0>, <&vdev0vring1>,
> > > <&vdev0buffer>,
> > > > +                               <&vdev1vring0>,
> <&vdev1vring1>,
> > > <&vdev0buffer>;
> > > > +       };
> > > > +
> > > > +       reserved-memory {
> > > > +               #address-cells = <2>;
> > > > +               #size-cells = <2>;
> > > > +               ranges;
> > > > +
> > > > +               vdev0vring0: vdev0vring0@90000000 {
> > > > +                       compatible = "shared-dma-pool";
> > > > +                       reg = <0 0x90000000 0 0x8000>;
> > > > +                       no-map;
> > > > +               };
> > > > +
> > > > +               vdev0vring1: vdev0vring1@90008000 {
> > > > +                       compatible = "shared-dma-pool";
> > > > +                       reg = <0 0x90008000 0 0x8000>;
> > > > +                       no-map;
> > > > +               };
> > > > +
> > > > +               vdev1vring0: vdev1vring0@90010000 {
> > > > +                       compatible = "shared-dma-pool";
> > > > +                       reg = <0 0x90010000 0 0x8000>;
> > > > +                       no-map;
> > > > +               };
> > > > +
> > > > +               vdev1vring1: vdev1vring1@90018000 {
> > > > +                       compatible = "shared-dma-pool";
> > > > +                       reg = <0 0x90018000 0 0x8000>;
> > > > +                       no-map;
> > > > +               };
> > > > +
> > > > +               vdev0buffer: vdev0buffer {
> > > > +                       compatible = "shared-dma-pool";
> > > > +                       reg = <0 0x90400000 0 0x100000>;
> > > > +                       no-map;
> > > > +               };
> > > > +       };
> > > > +
> > > >
> > > > Peng Fan (9):
> > > >   dt-bindings: remoteproc: Convert imx-rproc to json-schema
> > > >   dt-bindings: remoteproc: imx-rproc: support i.MX[8,8M,7ULP]
> > > >   remoteproc: add support to skip firmware load when recovery
> > > >   remoteproc: imx_rproc: surport early booted remote processor
> > > >   remoteproc: imx_rproc: parse early-booted property
> > > >   remoteproc: imx_proc: enable virtio/mailbox
> > > >   remoteproc: imx_rproc: add i.MX8QM/QXP
> > > >   remoteproc: imx_rproc: support i.MX7ULP
> > > >   remoteproc: imx_rproc: add i.MX8MM support
> > > >
> > > >  .../devicetree/bindings/remoteproc/imx-rproc.txt   |  33 --
> > > >  .../devicetree/bindings/remoteproc/imx-rproc.yaml  |  95 +++++
> > > >  drivers/remoteproc/imx_rproc.c                     | 455
> > > +++++++++++++++++++--
> > > >  drivers/remoteproc/remoteproc_core.c               |  19 +-
> > > >  include/linux/remoteproc.h                         |   1 +
> > > >  5 files changed, 531 insertions(+), 72 deletions(-)  delete mode
> > > > 100644 Documentation/devicetree/bindings/remoteproc/imx-rproc.txt
> > > >  create mode 100644
> > > > Documentation/devicetree/bindings/remoteproc/imx-rproc.yaml
> > > >
> > > > --
> > > > 2.16.4
> > > >




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux