add i2c, spi, crypto, rng, watchdog, peripheral nodes, also add support for wcss Q6 remoteproc driver and enable hw mutex, smem, mailbox, smp2p and rpmsg drivers Signed-off-by: Sivaprakash Murugesan <sivaprak@xxxxxxxxxxxxxx> --- [V2] * Addressed review comments from Stephen This patch depends on Sricharan's ipq6018 dts patch https://patchwork.kernel.org/patch/11340681/ arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts | 34 ++++ arch/arm64/boot/dts/qcom/ipq6018.dtsi | 226 +++++++++++++++++++++++++++ 2 files changed, 260 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts index 897b4b2..b31117a 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts +++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts @@ -28,3 +28,37 @@ pinctrl-names = "default"; status = "ok"; }; + +&i2c_1 { + pinctrl-0 = <&i2c_1_pins>; + pinctrl-names = "default"; + status = "ok"; +}; + +&spi_0 { + cs-select = <0>; + status = "ok"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "n25q128a11"; + spi-max-frequency = <50000000>; + }; +}; + +&tlmm { + i2c_1_pins: i2c-1-pins { + pins = "gpio42", "gpio43"; + function = "blsp2_i2c"; + drive-strength = <8>; + }; + + spi_0_pins: spi-0-pins { + pins = "gpio38", "gpio39", "gpio40", "gpio41"; + function = "blsp0_spi"; + drive-strength = <8>; + bias-pull-down; + }; +}; diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi index 0fb44e5..1aa8d85 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -7,6 +7,7 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,gcc-ipq6018.h> +#include <dt-bindings/reset/qcom,gcc-ipq6018.h> / { #address-cells = <2>; @@ -69,6 +70,18 @@ }; }; + firmware { + scm { + compatible = "qcom,scm"; + }; + }; + + tcsr_mutex: hwlock { + compatible = "qcom,tcsr-mutex"; + syscon = <&tcsr_mutex_regs 0 0x80>; + #hwlock-cells = <1>; + }; + pmuv8: pmu { compatible = "arm,cortex-a53-pmu"; interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | @@ -89,6 +102,22 @@ reg = <0x0 0x48500000 0x0 0x00200000>; no-map; }; + + smem_region: memory@4aa00000 { + reg = <0x0 0x4aa00000 0x0 0x00100000>; + no-map; + }; + + q6_region: memory@4ab00000 { + reg = <0x0 0x4ab00000 0x0 0x02800000>; + no-map; + }; + }; + + smem { + compatible = "qcom,smem"; + memory-region = <&smem_region>; + hwlocks = <&tcsr_mutex 0>; }; soc: soc { @@ -98,6 +127,36 @@ dma-ranges; compatible = "simple-bus"; + prng: qrng@e1000 { + compatible = "qcom,prng-ee"; + reg = <0xe3000 0x1000>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + }; + + cryptobam: dma@704000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x00704000 0x20000>; + interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_CRYPTO_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <1>; + qcom,controlled-remotely = <1>; + qcom,config-pipe-trust-reg = <0>; + }; + + crypto: crypto@73a000 { + compatible = "qcom,crypto-v5.1"; + reg = <0x0073a000 0x6000>; + clocks = <&gcc GCC_CRYPTO_AHB_CLK>, + <&gcc GCC_CRYPTO_AXI_CLK>, + <&gcc GCC_CRYPTO_CLK>; + clock-names = "iface", "bus", "core"; + dmas = <&cryptobam 2>, <&cryptobam 3>; + dma-names = "rx", "tx"; + }; + tlmm: pinctrl@1000000 { compatible = "qcom,ipq6018-pinctrl"; reg = <0x01000000 0x300000>; @@ -125,6 +184,26 @@ #reset-cells = <1>; }; + tcsr_mutex_regs: syscon@1905000 { + compatible = "syscon"; + reg = <0x01905000 0x8000>; + }; + + tcsr_q6: syscon@1945000 { + compatible = "syscon"; + reg = <0x01945000 0xe000>; + }; + + blsp_dma: dma@7884000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x07884000 0x2b000>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + blsp1_uart3: serial@78b1000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x078b1000 0x200>; @@ -135,6 +214,66 @@ status = "disabled"; }; + spi_0: spi@78b5000 { + compatible = "qcom,spi-qup-v2.2.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x078b5000 0x600>; + interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp_dma 12>, <&blsp_dma 13>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + spi_1: spi@78b6000 { + compatible = "qcom,spi-qup-v2.2.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x078b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + spi-max-frequency = <50000000>; + clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp_dma 14>, <&blsp_dma 15>; + dma-names = "tx", "rx"; + status = "disabled"; + }; + + i2c_0: i2c@78b6000 { + compatible = "qcom,i2c-qup-v2.2.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x078b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp_dma 15>, <&blsp_dma 14>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */ + compatible = "qcom,i2c-qup-v2.2.1"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x078b7000 0x600>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp_dma 17>, <&blsp_dma 16>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + intc: interrupt-controller@b000000 { compatible = "qcom,msm-qgic2"; interrupt-controller; @@ -146,6 +285,21 @@ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; }; + watchdog@b017000 { + compatible = "qcom,kpss-wdt"; + interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; + reg = <0x0b017000 0x40>; + clocks = <&sleep_clk>; + timeout-sec = <10>; + }; + + apcs_glb: mailbox@b111000 { + compatible = "qcom,ipq8074-apcs-apps-global"; + reg = <0x0b111000 0xc>; + + #mbox-cells = <1>; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -213,5 +367,77 @@ }; }; + q6v5_wcss: remoteproc@cd00000 { + compatible = "qcom,ipq8074-wcss-pil"; + reg = <0x0cd00000 0x4040>, + <0x004ab000 0x20>; + reg-names = "qdsp6", + "rmb"; + interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>, + <&wcss_smp2p_in 0 0>, + <&wcss_smp2p_in 1 0>, + <&wcss_smp2p_in 2 0>, + <&wcss_smp2p_in 3 0>; + interrupt-names = "wdog", + "fatal", + "ready", + "handover", + "stop-ack"; + + resets = <&gcc GCC_WCSSAON_RESET>, + <&gcc GCC_WCSS_BCR>, + <&gcc GCC_WCSS_Q6_BCR>; + + reset-names = "wcss_aon_reset", + "wcss_reset", + "wcss_q6_reset"; + + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "prng"; + + qcom,halt-regs = <&tcsr_q6 0xa000 0xd000 0x0>; + + qcom,smem-states = <&wcss_smp2p_out 0>, + <&wcss_smp2p_out 1>; + qcom,smem-state-names = "shutdown", + "stop"; + + memory-region = <&q6_region>; + + glink-edge { + interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>; + qcom,remote-pid = <1>; + mboxes = <&apcs_glb 8>; + + qrtr_requests { + qcom,glink-channels = "IPCRTR"; + }; + }; + }; + + }; + + wcss: wcss-smp2p { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupt-parent = <&intc>; + interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs_glb 9>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + wcss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + wcss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + interrupt-controller; + #interrupt-cells = <2>; + }; }; }; -- 2.7.4
