The R7 tv-dongle is an A10s based hdmi tv dongle, with 1G RAM, 4G nand flash, and rtl8189es sdio wifi. It has a standard male hdmi connector, an USB host port using an USB-A receptacle and a micro-usb receptacle for both power and USB OTG. Signed-off-by: Hans de Goede <hdegoede@xxxxxxxxxx> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts | 100 ++++++++++++++++++++++++++ 2 files changed, 101 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3a38a66..e4c5a79 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -341,6 +341,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \ sun4i-a10-olinuxino-lime.dtb \ sun4i-a10-pcduino.dtb \ sun5i-a10s-olinuxino-micro.dtb \ + sun5i-a10s-r7-tv-dongle.dtb \ sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino-micro.dtb \ sun6i-a31-app4-evb1.dtb \ diff --git a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts new file mode 100644 index 0000000..43a9376 --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts @@ -0,0 +1,100 @@ +/* + * Copyright 2014 Hans de Goede <hdegoede@xxxxxxxxxx> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun5i-a10s.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "R7 A10s hdmi tv-stick"; + compatible = "allwinner,r7-tv-dongle", "allwinner,sun5i-a10s"; + + soc@01c00000 { + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 1 0>; /* PG1 */ + cd-inverted; + status = "okay"; + }; + + mmc1: mmc@01c10000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + non-removable; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + pinctrl@01c20800 { + mmc0_cd_pin_r7: mmc0_cd_pin@0 { + allwinner,pins = "PG1"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + + led_pins_r7: led_pins@0 { + allwinner,pins = "PB2"; + allwinner,function = "gpio_out"; + allwinner,drive = <1>; + allwinner,pull = <0>; + }; + + usb1_vbus_pin_r7: usb1_vbus_pin@0 { + allwinner,pins = "PG13"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_r7>; + + green { + label = "r7-tv-dongle:green:usr"; + gpios = <&pio 1 2 0>; + default-state = "on"; + }; + }; + + reg_usb1_vbus: usb1-vbus { + pinctrl-0 = <&usb1_vbus_pin_r7>; + gpio = <&pio 6 13 0>; + status = "okay"; + }; +}; -- 1.9.0 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
