This adds the thermal sensor driver for the Broadcom BCM2711 SoC,
which is placed on the Raspberry Pi 4. The driver only provides
SoC temperature reading so far.
Signed-off-by: Stefan Wahren <wahrenst@xxxxxxx>
Reviewed-by: Florian Fainelli <f.fainelli@xxxxxxxxx>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@xxxxxxx>
---
drivers/thermal/broadcom/Kconfig | 7 ++
drivers/thermal/broadcom/Makefile | 1 +
drivers/thermal/broadcom/bcm2711_thermal.c | 129 +++++++++++++++++++++++++++++
3 files changed, 137 insertions(+)
create mode 100644 drivers/thermal/broadcom/bcm2711_thermal.c
diff --git a/drivers/thermal/broadcom/Kconfig b/drivers/thermal/broadcom/Kconfig
index cf43e15..061f1db 100644
--- a/drivers/thermal/broadcom/Kconfig
+++ b/drivers/thermal/broadcom/Kconfig
@@ -1,4 +1,11 @@
# SPDX-License-Identifier: GPL-2.0-only
+config BCM2711_THERMAL
+ tristate "Broadcom AVS RO thermal sensor driver"
+ depends on ARCH_BCM2835 || COMPILE_TEST
+ depends on THERMAL_OF && MFD_SYSCON
+ help
+ Support for thermal sensors on Broadcom BCM2711 SoCs.
+
config BCM2835_THERMAL
tristate "Thermal sensors on bcm2835 SoC"
depends on ARCH_BCM2835 || COMPILE_TEST
diff --git a/drivers/thermal/broadcom/Makefile b/drivers/thermal/broadcom/Makefile
index 490ab1f..c917b24 100644
--- a/drivers/thermal/broadcom/Makefile
+++ b/drivers/thermal/broadcom/Makefile
@@ -1,4 +1,5 @@
# SPDX-License-Identifier: GPL-2.0-only
+obj-$(CONFIG_BCM2711_THERMAL) += bcm2711_thermal.o
obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
obj-$(CONFIG_BRCMSTB_THERMAL) += brcmstb_thermal.o
obj-$(CONFIG_BCM_NS_THERMAL) += ns-thermal.o
diff --git a/drivers/thermal/broadcom/bcm2711_thermal.c b/drivers/thermal/broadcom/bcm2711_thermal.c
new file mode 100644
index 0000000..b1d3c4d
--- /dev/null
+++ b/drivers/thermal/broadcom/bcm2711_thermal.c
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Broadcom AVS RO thermal sensor driver
+ *
+ * based on brcmstb_thermal
+ *
+ * Copyright (C) 2020 Stefan Wahren
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/thermal.h>
+
+#include "../thermal_hwmon.h"
+
+#define AVS_RO_TEMP_STATUS 0x200
+ #define AVS_RO_TEMP_STATUS_valid_msk (BIT(16) | BIT(10))
+ #define AVS_RO_TEMP_STATUS_data_msk GENMASK(9, 0)
+
+struct bcm2711_thermal_priv {
+ struct regmap *regmap;
+ struct device *dev;
+ struct thermal_zone_device *thermal;
+};
+
+static int bcm2711_get_temp(void *data, int *temp)
+{
+ struct bcm2711_thermal_priv *priv = data;
+ int slope = thermal_zone_get_slope(priv->thermal);
+ int offset = thermal_zone_get_offset(priv->thermal);
+ u32 val;
+ int ret;
+ long t;
+
+ ret = regmap_read(priv->regmap, AVS_RO_TEMP_STATUS, &val);
+ if (ret)
+ return ret;
+
+ if (!(val & AVS_RO_TEMP_STATUS_valid_msk)) {
+ dev_err(priv->dev, "reading not valid\n");
+ return -EIO;
+ }
+
+ val &= AVS_RO_TEMP_STATUS_data_msk;
+
+ /* Convert a HW code to a temperature reading (millidegree celsius) */
+ t = slope * val + offset;
+ if (t < 0)
+ *temp = 0;
+ else
+ *temp = t;
+
+ return 0;
+}
+
+static const struct thermal_zone_of_device_ops bcm2711_thermal_of_ops = {
+ .get_temp = bcm2711_get_temp,
+};
+
+static const struct of_device_id bcm2711_thermal_id_table[] = {
+ { .compatible = "brcm,bcm2711-thermal" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, bcm2711_thermal_id_table);
+
+static int bcm2711_thermal_probe(struct platform_device *pdev)
+{
+ struct thermal_zone_device *thermal;
+ struct bcm2711_thermal_priv *priv;
+ struct device *dev = &pdev->dev;
+ struct device_node *parent;
+ struct regmap *regmap;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ /* get regmap from syscon node */
+ parent = of_get_parent(dev->of_node); /* parent should be syscon node */
+ regmap = syscon_node_to_regmap(parent);
+ of_node_put(parent);
+ if (IS_ERR(regmap)) {
+ ret = PTR_ERR(regmap);
+ dev_err(dev, "failed to get regmap: %d\n", ret);
+ return ret;
+ }
+ priv->regmap = regmap;
+ priv->dev = dev;
+
+ thermal = devm_thermal_zone_of_sensor_register(dev, 0, priv,
+ &bcm2711_thermal_of_ops);
+ if (IS_ERR(thermal)) {
+ ret = PTR_ERR(thermal);
+ dev_err(dev, "could not register sensor: %d\n", ret);
+ return ret;
+ }
+
+ priv->thermal = thermal;
+
+ thermal->tzp->no_hwmon = false;
+ ret = thermal_add_hwmon_sysfs(thermal);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static struct platform_driver bcm2711_thermal_driver = {
+ .probe = bcm2711_thermal_probe,
+ .driver = {
+ .name = "bcm2711_thermal",
+ .of_match_table = bcm2711_thermal_id_table,
+ },
+};
+module_platform_driver(bcm2711_thermal_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Stefan Wahren");
+MODULE_DESCRIPTION("Broadcom AVS RO thermal sensor driver");
--
2.7.4
