On Mon, Dec 09, 2019 at 07:44:04PM +0800, Chunyan Zhang wrote:
> From: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
>
> Add basic DT to support Unisoc's SC9863A, with this patch,
> the board sp9863a-1h10 can run into console.
>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@xxxxxxxxxx>
> ---
> arch/arm64/boot/dts/sprd/Makefile | 3 +-
> arch/arm64/boot/dts/sprd/sc9863a.dtsi | 523 ++++++++++++++++++++++
> arch/arm64/boot/dts/sprd/sharkl3.dtsi | 148 ++++++
> arch/arm64/boot/dts/sprd/sp9863a-1h10.dts | 39 ++
> 4 files changed, 712 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm64/boot/dts/sprd/sc9863a.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sharkl3.dtsi
> create mode 100644 arch/arm64/boot/dts/sprd/sp9863a-1h10.dts
> diff --git a/arch/arm64/boot/dts/sprd/sharkl3.dtsi b/arch/arm64/boot/dts/sprd/sharkl3.dtsi
> new file mode 100644
> index 000000000000..3b5a94560481
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sharkl3.dtsi
> @@ -0,0 +1,148 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Unisoc Sharkl3 platform DTS file
> + *
> + * Copyright (C) 2019, Unisoc Inc.
> + */
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + soc: soc {
> + compatible = "simple-bus";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + ap_ahb_regs: syscon@20e00000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x20e00000 0 0x4000>;
> + };
> +
> + pub_ctrl_regs: syscon@300e0000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
Having a bunch of the same compatible doesn't look right. I assume by
the label names each of these are a different set of registers. The
compatible should be specific enough the OS can match to a driver that
knows the register details.
Doesn't look like you use all these, so maybe drop until you do and/or
figure out if you can use common bindings for some of these.
> + reg = <0 0x300e0000 0 0x4000>;
> + };
> +
> + pub_wrap_regs: syscon@300f0000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x300f0000 0 0x1000>;
> + };
> +
> + pmu_regs: syscon@402b0000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x402b0000 0 0x4000>;
> + };
> +
> + aon_apb_regs: syscon@402e0000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x402e0000 0 0x4000>;
> + };
> +
> + anlg_phy_g1_regs: syscon@40350000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x40350000 0 0x3000>;
> + };
> +
> + anlg_phy_g2_regs: syscon@40353000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x40353000 0 0x3000>;
> + };
> +
> + anlg_phy_g4_regs: syscon@40359000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x40359000 0 0x3000>;
> + };
> +
> + anlg_phy_g5_regs: syscon@4035c000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x4035c000 0 0x3000>;
> + };
> +
> + anlg_phy_g7_regs: syscon@40363000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x40363000 0 0x3000>;
> + };
> +
> + anlg_wrap_wcn_regs: syscon@40366000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x40366000 0 0x3000>;
> + };
> +
> + mm_ahb_regs: syscon@60800000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x60800000 0 0x1000>;
> + };
> +
> + mm_vsp_ahb_regs: syscon@62000000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x62000000 0 0x1000>;
> + };
> +
> + ap_apb_regs: syscon@71300000 {
> + compatible = "sprd,sc9863a-glbregs", "syscon";
> + reg = <0 0x71300000 0 0x4000>;
> + };
> +
> + apb@70000000 {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x0 0x70000000 0x10000000>;
> +
> + uart0: serial@0 {
> + compatible = "sprd,sc9863a-uart",
> + "sprd,sc9836-uart";
> + reg = <0x0 0x100>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart1: serial@100000 {
> + compatible = "sprd,sc9863a-uart",
> + "sprd,sc9836-uart";
> + reg = <0x100000 0x100>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart2: serial@200000 {
> + compatible = "sprd,sc9863a-uart",
> + "sprd,sc9836-uart";
> + reg = <0x200000 0x100>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart3: serial@300000 {
> + compatible = "sprd,sc9863a-uart",
> + "sprd,sc9836-uart";
> + reg = <0x300000 0x100>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> +
> + uart4: serial@400000 {
> + compatible = "sprd,sc9863a-uart",
> + "sprd,sc9836-uart";
> + reg = <0x400000 0x100>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ext_26m>;
> + status = "disabled";
> + };
> + };
> + };
> +
> + ext_26m: ext-26m {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <26000000>;
> + clock-output-names = "ext-26m";
> + };
> +};
> diff --git a/arch/arm64/boot/dts/sprd/sp9863a-1h10.dts b/arch/arm64/boot/dts/sprd/sp9863a-1h10.dts
> new file mode 100644
> index 000000000000..5c32c1596337
> --- /dev/null
> +++ b/arch/arm64/boot/dts/sprd/sp9863a-1h10.dts
> @@ -0,0 +1,39 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Unisoc SP9863A-1h10 boards DTS file
> + *
> + * Copyright (C) 2019, Unisoc Inc.
> + */
> +
> +/dts-v1/;
> +
> +#include "sc9863a.dtsi"
> +
> +/ {
> + model = "Spreadtrum SP9863A-1H10 Board";
> +
> + compatible = "sprd,sp9863a-1h10", "sprd,sc9863a";
> +
> + aliases {
> + serial0 = &uart0;
> + serial1 = &uart1;
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x0 0x80000000 0x0 0x80000000>;
> + };
> +
> + chosen {
> + stdout-path = "serial1:115200n8";
> + bootargs = "earlycon";
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> --
> 2.20.1
>
