Support the Ingenic X1000 SoC using the code under arch/mips/jz4740.
This is left unselectable in Kconfig until a X1000 based board is
added in a later commit.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>
---
Notes:
v1->v2:
Rebase on top of mips-next, use ingenic-timer driver
for system timer and clocksource.
v2->v3:
Drop the 'apb' node.
v3->v4:
Adjust the node order to make it consistent with
other Ingenic boards.
v4->v5:
No change.
v5->v6:
No change.
v6->v7:
Change my Signed-off-by from "Zhou Yanjie <zhouyanjie@xxxxxxxx>"
to "周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>" because
the old mailbox is in an unstable state.
arch/mips/boot/dts/ingenic/x1000.dtsi | 176 ++++++++++++++++++++++++++++++++++
arch/mips/jz4740/Kconfig | 6 ++
2 files changed, 182 insertions(+)
create mode 100644 arch/mips/boot/dts/ingenic/x1000.dtsi
diff --git a/arch/mips/boot/dts/ingenic/x1000.dtsi b/arch/mips/boot/dts/ingenic/x1000.dtsi
new file mode 100644
index 00000000..13a6c9ff
--- /dev/null
+++ b/arch/mips/boot/dts/ingenic/x1000.dtsi
@@ -0,0 +1,176 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/clock/x1000-cgu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "ingenic,x1000", "ingenic,x1000e";
+
+ cpuintc: interrupt-controller {
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ interrupt-controller;
+ compatible = "mti,cpu-interrupt-controller";
+ };
+
+ intc: interrupt-controller@10001000 {
+ compatible = "ingenic,x1000-intc", "ingenic,jz4780-intc";
+ reg = <0x10001000 0x50>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&cpuintc>;
+ interrupts = <2>;
+ };
+
+ exclk: ext {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ rtclk: rtc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ };
+
+ cgu: x1000-cgu@10000000 {
+ compatible = "ingenic,x1000-cgu";
+ reg = <0x10000000 0x100>;
+
+ #clock-cells = <1>;
+
+ clocks = <&exclk>, <&rtclk>;
+ clock-names = "ext", "rtc";
+ };
+
+ tcu: timer@10002000 {
+ compatible = "ingenic,x1000-tcu",
+ "ingenic,jz4770-tcu",
+ "simple-mfd";
+ reg = <0x10002000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x10002000 0x1000>;
+
+ #clock-cells = <1>;
+
+ clocks = <&cgu X1000_CLK_RTCLK
+ &cgu X1000_CLK_EXCLK
+ &cgu X1000_CLK_PCLK>;
+ clock-names = "rtc", "ext", "pclk";
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <27 26 25>;
+ };
+
+ pinctrl: pin-controller@10010000 {
+ compatible = "ingenic,x1000-pinctrl";
+ reg = <0x10010000 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpa: gpio@0 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <0>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 0 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <17>;
+ };
+
+ gpb: gpio@1 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <1>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 32 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <16>;
+ };
+
+ gpc: gpio@2 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <2>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 64 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <15>;
+ };
+
+ gpd: gpio@3 {
+ compatible = "ingenic,x1000-gpio";
+ reg = <3>;
+
+ gpio-controller;
+ gpio-ranges = <&pinctrl 0 96 32>;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <14>;
+ };
+ };
+
+ uart0: serial@10030000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10030000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <51>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART0>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart1: serial@10031000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10031000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <50>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART1>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+
+ uart2: serial@10032000 {
+ compatible = "ingenic,x1000-uart";
+ reg = <0x10032000 0x100>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <49>;
+
+ clocks = <&exclk>, <&cgu X1000_CLK_UART2>;
+ clock-names = "baud", "module";
+
+ status = "disabled";
+ };
+};
diff --git a/arch/mips/jz4740/Kconfig b/arch/mips/jz4740/Kconfig
index 4dd0c44..6b96844 100644
--- a/arch/mips/jz4740/Kconfig
+++ b/arch/mips/jz4740/Kconfig
@@ -33,3 +33,9 @@ config MACH_JZ4780
select MIPS_CPU_SCACHE
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_HIGHMEM
+
+config MACH_X1000
+ bool
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_HIGHMEM
--
2.7.4
