Re: [PATCH V1 2/2] arm64: dts: qcom: sc7180: Add nodes for eMMC and SD card

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Wed, Nov 27, 2019 at 11:50:06AM +0000, Veerabhadrarao Badiganti wrote:

> Add sdhc instances for supporting eMMC and SD-card on sc7180.
> The regulators should be in HPM state for proper functionality of
> eMMC and SD-card. Updating corresponding regulators accordingly.
> 
> Signed-off-by: Veerabhadrarao Badiganti <vbadigan@xxxxxxxxxxxxxx>
> ---
> 
> This depends on the patch series (dt support for sc7180):
> https://lkml.org/lkml/2019/11/8/149
> ---
>  arch/arm64/boot/dts/qcom/sc7180-idp.dts |  32 +++++++-
>  arch/arm64/boot/dts/qcom/sc7180.dtsi    | 136 ++++++++++++++++++++++++++++++++
>  2 files changed, 164 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> index 189254f..583c42c 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> +++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
> @@ -11,6 +11,7 @@
>  #include "sc7180.dtsi"
>  #include "pm6150.dtsi"
>  #include "pm6150l.dtsi"
> +#include <dt-bindings/gpio/gpio.h>

I think this should be above, together with
'dt-bindings/regulator/qcom,rpmh-regulator.h'

>  
>  / {
>  	model = "Qualcomm Technologies, Inc. SC7180 IDP";
> @@ -103,7 +104,7 @@
>  		vreg_l12a_1p8: ldo12 {
>  			regulator-min-microvolt = <1696000>;
>  			regulator-max-microvolt = <1952000>;
> -			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
>  		vreg_l13a_1p8: ldo13 {
> @@ -145,7 +146,7 @@
>  		vreg_l19a_2p9: ldo19 {
>  			regulator-min-microvolt = <2696000>;
>  			regulator-max-microvolt = <3304000>;
> -			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  	};
>  
> @@ -191,7 +192,7 @@
>  		vreg_l6c_2p9: ldo6 {
>  			regulator-min-microvolt = <2696000>;
>  			regulator-max-microvolt = <3304000>;
> -			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
>  		vreg_l7c_3p0: ldo7 {
> @@ -209,7 +210,7 @@
>  		vreg_l9c_2p9: ldo9 {
>  			regulator-min-microvolt = <2952000>;
>  			regulator-max-microvolt = <3304000>;
> -			regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>  		};
>  
>  		vreg_l10c_3p3: ldo10 {
> @@ -400,3 +401,26 @@
>  			bias-pull-up;
>  		};
>  };
> +
> +&sdhc_1 {
> +	status = "ok";
> +
> +	pinctrl-names = "default", "sleep";
> +	pinctrl-0 = <&sdc1_on>;
> +	pinctrl-1 = <&sdc1_off>;
> +	vmmc-supply = <&vreg_l19a_2p9>;
> +	vqmmc-supply = <&vreg_l12a_1p8>;
> +

remove empty line

> +};
> +
> +&sdhc_2 {
> +	status = "ok";
> +
> +	pinctrl-names = "default","sleep";
> +	pinctrl-0 = <&sdc2_on>;
> +	pinctrl-1 = <&sdc2_off>;
> +	vmmc-supply  = <&vreg_l9c_2p9>;
> +	vqmmc-supply = <&vreg_l6c_2p9>;
> +
> +	cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 666e9b9..207d44f 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -897,6 +897,100 @@
>  					function = "qup15";
>  				};
>  			};
> +
> +			sdc1_on: sdc1-on {
> +				clk {
> +					pins = "sdc1_clk";
> +					bias-disable;
> +					drive-strength = <16>;
> +				};
> +
> +				cmd {
> +					pins = "sdc1_cmd";
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +
> +				data {
> +					pins = "sdc1_data";
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +
> +				rclk {
> +					pins = "sdc1_rclk";
> +					bias-pull-down;
> +				};
> +			};
> +
> +			sdc1_off: sdc1-off {
> +				clk {
> +					pins = "sdc1_clk";
> +					bias-disable;
> +					drive-strength = <2>;
> +				};
> +
> +				cmd {
> +					pins = "sdc1_cmd";
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +
> +				data {
> +					pins = "sdc1_data";
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +
> +				rclk {
> +					pins = "sdc1_rclk";
> +					bias-pull-down;
> +				};
> +			};
> +
> +			sdc2_on: sdc2_on {
> +				clk {
> +					pins = "sdc2_clk";
> +					bias-disable;
> +					drive-strength = <16>;
> +				};

nit: add blank lines, consistent with the other pinconf entries.

> +				cmd {
> +					pins = "sdc2_cmd";
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				data {
> +					pins = "sdc2_data";
> +					bias-pull-up;
> +					drive-strength = <10>;
> +				};
> +				sd-cd {
> +					pins = "gpio69";
> +					bias-pull-down;
> +				};
> +			};
> +
> +			sdc2_off: sdc2_off {
> +				clk {
> +					pins = "sdc2_clk";
> +					bias-disable;
> +					drive-strength = <2>;
> +				};
> +				cmd {
> +					pins = "sdc2_cmd";
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +				data {
> +					pins = "sdc2_data";
> +					bias-pull-up;
> +					drive-strength = <2>;
> +				};
> +				sd-cd {
> +					pins = "gpio69";
> +					bias-pull-down;
> +				};
> +			};
>  		};
>  
>  		qspi: spi@88dc000 {
> @@ -911,6 +1005,48 @@
>  			status = "disabled";
>  		};
>  
> +		sdhc_1: sdhci@7c4000 {

IIUC the nodes are ordered by address, hence this one should be between
'clock-controller@100000' and 'geniqup@8c0000'.

> +			compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> +			reg = <0 0x7c4000 0 0x1000>;
> +			reg-names = "hc_mem";
> +
> +			interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
> +					<&gcc GCC_SDCC1_AHB_CLK>;
> +			clock-names = "core", "iface";
> +
> +			bus-width = <8>;
> +			non-removable;
> +
> +			mmc-ddr-1_8v;
> +			mmc-hs200-1_8v;
> +			mmc-hs400-1_8v;
> +			mmc-hs400-enhanced-strobe;
> +
> +			status = "disabled";
> +		};
> +
> +		sdhc_2: sdhci@8804000 {

nodes are ordered by address: this one should be between 'pinctrl@3500000'
and 'spi@88dc000´.

> +			compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
> +			reg = <0 0x08804000 0 0x1000>;
> +			reg-names = "hc_mem";
> +
> +			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "hc_irq", "pwr_irq";
> +
> +			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
> +					<&gcc GCC_SDCC2_AHB_CLK>;
> +			clock-names = "core","iface";

nit: add a blank after the comma.

Thanks

Matthias



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux