Re: [RFC] Describing arbitrary bus mastering relationships in DT

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Friday 02 May 2014 12:50:17 Stephen Warren wrote:
> On 05/02/2014 07:23 AM, Thierry Reding wrote:
> > On Fri, May 02, 2014 at 02:32:08PM +0200, Arnd Bergmann wrote:
> >> On Friday 02 May 2014 13:05:58 Thierry Reding wrote:
> >>>
> >>> Let me see if I understood the above proposal by trying to translate it
> >>> into a simple example for a specific use-case. On Tegra for example we
> >>> have various units that can either access system memory directly or use
> >>> the IOMMU to translate accesses for them. One such unit would be the
> >>> display controller that scans out a framebuffer from memory.
> >>
> >> Can you explain how the decision is made whether the IOMMU gets used
> >> or not? In all cases I've seen so far, I think we can hardwire this
> >> in DT, and only expose one or the other. Are both ways used
> >> concurrently?
> > 
> > It should be possible to hardcode this in DT for Tegra. As I understand
> > it, both interfaces can't be used at the same time. Once translation has
> > been enabled for one client, all accesses generated by that client will
> > be translated.
> > 
> > Hiroshi, please correct me if I'm wrong.
> 
> I believe the HW connectivity is always as follows:
> 
> Bus master (e.g. display controller) ---> IOMMU (Tegra SMMU) ---> RAM
> 
> In the IOMMU, there is a bit per bus master that indicates whether the
> IOMMU translates the bus master's accesses or not. If that bit is
> enabled, then page tables in the IOMMU are used to perform the translation.
> 
> You could also look at the HW setup as:
> 
> Bus master (e.g. display controller)
>     v
>    ----
>   /    \
>   ------
>    |  \
>    |   ------------------
>    |                     \
>    v                     v
> IOMMU (Tegra SMMU) ---> RAM
> 
> But IIRC the bit that controls that demux is in the IOMMU, so this
> distinction probably isn't relevant.

Ok. I think this case can be dealt with easily enough without
having to represent it as two master ports on one device. There
really is just one master, and it can be configured in two ways.

We can either choose to make the DT representation decide which
way is used, or we can always point to the IOMMU, and let the
IOMMU driver decide.

> Now, perhaps there are devices which themselves control whether
> transactions are sent to the IOMMU or direct to RAM, but I'm not
> familiar with them. Is the GPU in that category, since it has its own
> GMMU, albeit chained into the SMMU IIRC?

Devices with a built-in IOMMU such as most GPUs are also easy enough
to handle: There is no reason to actually show the IOMMU in DT and
we can just treat the GPU as a black box.

Note that you don't really have to support the dma-mapping.h API on
GPUs, they usually need to go down to the IOMMU level anyway.

	Arnd
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux