On Mon, Nov 25, 2019 at 12:30:53PM +0530, Vidya Sagar wrote:
> On 11/22/2019 6:55 PM, Thierry Reding wrote:
> > On Fri, Nov 22, 2019 at 04:15:05PM +0530, Vidya Sagar wrote:
> > > Add endpoint mode support for PCIe C5 controller in P2972-0000 platform
> > > with information about supplies, PHY, PERST GPIO and GPIO that controls
> > > PCIe reference clock coming from the host system.
> > >
> > > Signed-off-by: Vidya Sagar <vidyas@xxxxxxxxxx>
> > > ---
> > > .../boot/dts/nvidia/tegra194-p2972-0000.dts | 29 +++++++++++++++++++
> > > 1 file changed, 29 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
> > > index 7eb64b816e08..58c3a9677bc8 100644
> > > --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
> > > +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
> > > @@ -43,6 +43,19 @@
> > > gpio@c2f0000 {
> > > status = "okay";
> > > + /*
> > > + * Change the below node's status to 'okay' when
> > > + * PCIe C5 controller is enabled to operate in endpoint
> > > + * to allow REFCLK from the host system to flow into
> > > + * the controller.
> > > + */
> > > + pex-refclk-sel-high {
> > > + gpio-hog;
> > > + output-high;
> > > + gpios = <TEGRA194_AON_GPIO(AA, 5) 0>;
> > > + label = "pex_refclk_sel_high";
> > > + status = "disabled";
> > > + };
> >
> > Why don't we put this into the PCIe controller's node as a reference to
> > that GPIO? Seems like the controller would know exactly when this pin
> > needs to go high or low, so why does it have to be a hog?
> >
> > Thierry
> Are you saying something like 'nvidia,enable-refclk-in'?
> I was thinking, since this is like a board level configuration specific to Jetson-Xavier,
> it would suffice to just hog it according to the mode of operation of PCIe controller.
> But, I see one advantage of referencing it in the PCIe node (so that the driver can configure
> it as and when needed) is that one has to be careful just to enable either PCIe RP or EP
> node and not worry about other thing (like this).
> Let me know if I got this right.
Yeah, that's exactly why I think referencing this from the controller
and controlling it in the driver is preferable.
If this is some sort of select signal I think it makes sense to name it
"nvidia,refclk-select-gpios" or something. Does this appear in the
schematic somewhere? Or does the IP have a name for this? Those are
usually good places to look for inspiration on the name because it's
what hardware designers will be familiar with and they are technically
the ones who should write the DT, even if that's rarely the case.
Thierry
>
> - Vidya Sagar
>
> >
> > > };
> > > pwm@c340000 {
> > > @@ -144,6 +157,22 @@
> > > "p2u-5", "p2u-6", "p2u-7";
> > > };
> > > + pcie_ep@141a0000 {
> > > + status = "disabled";
> > > +
> > > + vddio-pex-ctl-supply = <&vdd_1v8ao>;
> > > +
> > > + nvidia,pex-rst-gpio = <&gpio TEGRA194_MAIN_GPIO(GG, 1)
> > > + GPIO_ACTIVE_LOW>;
> > > +
> > > + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
> > > + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
> > > + <&p2u_nvhs_6>, <&p2u_nvhs_7>;
> > > +
> > > + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
> > > + "p2u-5", "p2u-6", "p2u-7";
> > > + };
> > > +
> > > fan: fan {
> > > compatible = "pwm-fan";
> > > pwms = <&pwm4 0 45334>;
> > > --
> > > 2.17.1
> > >
>
Attachment:
signature.asc
Description: PGP signature
