On Tue, Nov 12, 2019 at 05:30:01PM -0500, Eric Tremblay wrote: > TI's TMP512/513 are I2C/SMBus system monitor chips. These chips > monitor the supply voltage, supply current, power consumption > and provide one local and up to three (TMP513) remote temperature sensors. > > It has been tested using a TI TMP513 development kit (TMP513EVM) > > Signed-off-by: Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx> Applied. Thanks, Guenter > --- > Documentation/hwmon/index.rst | 1 + > Documentation/hwmon/tmp513.rst | 103 +++++ > MAINTAINERS | 7 + > drivers/hwmon/Kconfig | 10 + > drivers/hwmon/Makefile | 1 + > drivers/hwmon/tmp513.c | 772 +++++++++++++++++++++++++++++++++ > 6 files changed, 894 insertions(+) > create mode 100644 Documentation/hwmon/tmp513.rst > create mode 100644 drivers/hwmon/tmp513.c > > diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst > index 230ad59b462b..d708a371fce1 100644 > --- a/Documentation/hwmon/index.rst > +++ b/Documentation/hwmon/index.rst > @@ -153,6 +153,7 @@ Hardware Monitoring Kernel Drivers > tmp108 > tmp401 > tmp421 > + tmp513 > tps40422 > twl4030-madc-hwmon > ucd9000 > diff --git a/Documentation/hwmon/tmp513.rst b/Documentation/hwmon/tmp513.rst > new file mode 100644 > index 000000000000..6c8fae4b1a75 > --- /dev/null > +++ b/Documentation/hwmon/tmp513.rst > @@ -0,0 +1,103 @@ > +.. SPDX-License-Identifier: GPL-2.0 > + > +Kernel driver tmp513 > +==================== > + > +Supported chips: > + > + * Texas Instruments TMP512 > + > + Prefix: 'tmp512' > + > + Datasheet: http://www.ti.com/lit/ds/symlink/tmp512.pdf > + > + * Texas Instruments TMP513 > + > + Prefix: 'tmp513' > + > + Datasheet: http://www.ti.com/lit/ds/symlink/tmp513.pdf > + > +Authors: > + > + Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx> > + > +Description > +----------- > + > +This driver implements support for Texas Instruments TMP512, and TMP513. > +The TMP512 (dual-channel) and TMP513 (triple-channel) are system monitors > +that include remote sensors, a local temperature sensor, and a high-side current > +shunt monitor. These system monitors have the capability of measuring remote > +temperatures, on-chip temperatures, and system voltage/power/current > +consumption. > + > +The temperatures are measured in degrees Celsius with a range of > +-40 to + 125 degrees with a resolution of 0.0625 degree C. > + > +For hysteresis value, only the first channel is writable. Writing to it > +will affect all other values since each channels are sharing the same > +hysteresis value. The hysteresis is in degrees Celsius with a range of > +0 to 127.5 degrees with a resolution of 0.5 degree. > + > +The driver exports the temperature values via the following sysfs files: > + > +**temp[1-4]_input** > + > +**temp[1-4]_crit** > + > +**temp[1-4]_crit_alarm** > + > +**temp[1-4]_crit_hyst** > + > +The driver read the shunt voltage from the chip and convert it to current. > +The readable range depends on the "ti,pga-gain" property (default to 8) and the > +shunt resistor value. The value resolution will be equal to 10uV/Rshunt. > + > +The driver exports the shunt currents values via the following sysFs files: > + > +**curr1_input** > + > +**curr1_lcrit** > + > +**curr1_lcrit_alarm** > + > +**curr1_crit** > + > +**curr1_crit_alarm** > + > +The bus voltage range is read from the chip with a resolution of 4mV. The chip > +can be configurable in two different range (32V or 16V) using the > +ti,bus-range-microvolt property in the devicetree. > + > +The driver exports the bus voltage values via the following sysFs files: > + > +**in0_input** > + > +**in0_lcrit** > + > +**in0_lcrit_alarm** > + > +**in0_crit** > + > +**in0_crit_alarm** > + > +The bus power and bus currents range and resolution depends on the calibration > +register value. Those values are calculate by the hardware using those > +formulas: > + > +Current = (ShuntVoltage * CalibrationRegister) / 4096 > +Power = (Current * BusVoltage) / 5000 > + > +The driver exports the bus current and bus power values via the following > +sysFs files: > + > +**curr2_input** > + > +**power1_input** > + > +**power1_crit** > + > +**power1_crit_alarm** > + > +The calibration process follow the procedure of the datasheet (without overflow) > +and depend on the shunt resistor value and the pga_gain value. > diff --git a/MAINTAINERS b/MAINTAINERS > index eb19fad370d7..75db98a0913c 100644 > --- a/MAINTAINERS > +++ b/MAINTAINERS > @@ -16378,6 +16378,13 @@ S: Maintained > F: Documentation/hwmon/tmp401.rst > F: drivers/hwmon/tmp401.c > > +TMP513 HARDWARE MONITOR DRIVER > +M: Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx> > +L: linux-hwmon@xxxxxxxxxxxxxxx > +S: Maintained > +F: Documentation/hwmon/tmp513.rst > +F: drivers/hwmon/tmp513.c > + > TMPFS (SHMEM FILESYSTEM) > M: Hugh Dickins <hughd@xxxxxxxxxx> > L: linux-mm@xxxxxxxxx > diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig > index 13a6b4afb4b3..926e3c98dbdf 100644 > --- a/drivers/hwmon/Kconfig > +++ b/drivers/hwmon/Kconfig > @@ -1709,6 +1709,16 @@ config SENSORS_TMP421 > This driver can also be built as a module. If so, the module > will be called tmp421. > > +config SENSORS_TMP513 > + tristate "Texas Instruments TMP513 and compatibles" > + depends on I2C > + help > + If you say yes here you get support for Texas Instruments TMP512, > + and TMP513 temperature and power supply sensor chips. > + > + This driver can also be built as a module. If so, the module > + will be called tmp513. > + > config SENSORS_VEXPRESS > tristate "Versatile Express" > depends on VEXPRESS_CONFIG > diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile > index 40c036ea45e6..762642291914 100644 > --- a/drivers/hwmon/Makefile > +++ b/drivers/hwmon/Makefile > @@ -166,6 +166,7 @@ obj-$(CONFIG_SENSORS_TMP103) += tmp103.o > obj-$(CONFIG_SENSORS_TMP108) += tmp108.o > obj-$(CONFIG_SENSORS_TMP401) += tmp401.o > obj-$(CONFIG_SENSORS_TMP421) += tmp421.o > +obj-$(CONFIG_SENSORS_TMP513) += tmp513.o > obj-$(CONFIG_SENSORS_VEXPRESS) += vexpress-hwmon.o > obj-$(CONFIG_SENSORS_VIA_CPUTEMP)+= via-cputemp.o > obj-$(CONFIG_SENSORS_VIA686A) += via686a.o > diff --git a/drivers/hwmon/tmp513.c b/drivers/hwmon/tmp513.c > new file mode 100644 > index 000000000000..df66e0bc1253 > --- /dev/null > +++ b/drivers/hwmon/tmp513.c > @@ -0,0 +1,772 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* > + * Driver for Texas Instruments TMP512, TMP513 power monitor chips > + * > + * TMP513: > + * Thermal/Power Management with Triple Remote and > + * Local Temperature Sensor and Current Shunt Monitor > + * Datasheet: http://www.ti.com/lit/gpn/tmp513 > + * > + * TMP512: > + * Thermal/Power Management with Dual Remote > + * and Local Temperature Sensor and Current Shunt Monitor > + * Datasheet: http://www.ti.com/lit/gpn/tmp512 > + * > + * Copyright (C) 2019 Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxxx> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License as published by > + * the Free Software Foundation; version 2 of the License. > + */ > + > +#include <linux/err.h> > +#include <linux/hwmon.h> > +#include <linux/i2c.h> > +#include <linux/init.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/regmap.h> > +#include <linux/slab.h> > +#include <linux/util_macros.h> > + > +// Common register definition > +#define TMP51X_SHUNT_CONFIG 0x00 > +#define TMP51X_TEMP_CONFIG 0x01 > +#define TMP51X_STATUS 0x02 > +#define TMP51X_SMBUS_ALERT 0x03 > +#define TMP51X_SHUNT_CURRENT_RESULT 0x04 > +#define TMP51X_BUS_VOLTAGE_RESULT 0x05 > +#define TMP51X_POWER_RESULT 0x06 > +#define TMP51X_BUS_CURRENT_RESULT 0x07 > +#define TMP51X_LOCAL_TEMP_RESULT 0x08 > +#define TMP51X_REMOTE_TEMP_RESULT_1 0x09 > +#define TMP51X_REMOTE_TEMP_RESULT_2 0x0A > +#define TMP51X_SHUNT_CURRENT_H_LIMIT 0x0C > +#define TMP51X_SHUNT_CURRENT_L_LIMIT 0x0D > +#define TMP51X_BUS_VOLTAGE_H_LIMIT 0x0E > +#define TMP51X_BUS_VOLTAGE_L_LIMIT 0x0F > +#define TMP51X_POWER_LIMIT 0x10 > +#define TMP51X_LOCAL_TEMP_LIMIT 0x11 > +#define TMP51X_REMOTE_TEMP_LIMIT_1 0x12 > +#define TMP51X_REMOTE_TEMP_LIMIT_2 0x13 > +#define TMP51X_SHUNT_CALIBRATION 0x15 > +#define TMP51X_N_FACTOR_AND_HYST_1 0x16 > +#define TMP51X_N_FACTOR_2 0x17 > +#define TMP51X_MAN_ID_REG 0xFE > +#define TMP51X_DEVICE_ID_REG 0xFF > + > +// TMP513 specific register definition > +#define TMP513_REMOTE_TEMP_RESULT_3 0x0B > +#define TMP513_REMOTE_TEMP_LIMIT_3 0x14 > +#define TMP513_N_FACTOR_3 0x18 > + > +// Common attrs, and NULL > +#define TMP51X_MANUFACTURER_ID 0x55FF > + > +#define TMP512_DEVICE_ID 0x22FF > +#define TMP513_DEVICE_ID 0x23FF > + > +// Default config > +#define TMP51X_SHUNT_CONFIG_DEFAULT 0x399F > +#define TMP51X_SHUNT_VALUE_DEFAULT 1000 > +#define TMP51X_VBUS_RANGE_DEFAULT TMP51X_VBUS_RANGE_32V > +#define TMP51X_PGA_DEFAULT 8 > +#define TMP51X_MAX_REGISTER_ADDR 0xFF > + > +#define TMP512_TEMP_CONFIG_DEFAULT 0xBF80 > +#define TMP513_TEMP_CONFIG_DEFAULT 0xFF80 > + > +// Mask and shift > +#define CURRENT_SENSE_VOLTAGE_320_MASK 0x1800 > +#define CURRENT_SENSE_VOLTAGE_160_MASK 0x1000 > +#define CURRENT_SENSE_VOLTAGE_80_MASK 0x0800 > +#define CURRENT_SENSE_VOLTAGE_40_MASK 0 > + > +#define TMP51X_BUS_VOLTAGE_MASK 0x2000 > +#define TMP51X_NFACTOR_MASK 0xFF00 > +#define TMP51X_HYST_MASK 0x00FF > + > +#define TMP51X_BUS_VOLTAGE_SHIFT 3 > +#define TMP51X_TEMP_SHIFT 3 > + > +// Alarms > +#define TMP51X_SHUNT_CURRENT_H_LIMIT_POS 15 > +#define TMP51X_SHUNT_CURRENT_L_LIMIT_POS 14 > +#define TMP51X_BUS_VOLTAGE_H_LIMIT_POS 13 > +#define TMP51X_BUS_VOLTAGE_L_LIMIT_POS 12 > +#define TMP51X_POWER_LIMIT_POS 11 > +#define TMP51X_LOCAL_TEMP_LIMIT_POS 10 > +#define TMP51X_REMOTE_TEMP_LIMIT_1_POS 9 > +#define TMP51X_REMOTE_TEMP_LIMIT_2_POS 8 > +#define TMP513_REMOTE_TEMP_LIMIT_3_POS 7 > + > +#define TMP51X_VBUS_RANGE_32V 32000000 > +#define TMP51X_VBUS_RANGE_16V 16000000 > + > +// Max and Min value > +#define MAX_BUS_VOLTAGE_32_LIMIT 32764 > +#define MAX_BUS_VOLTAGE_16_LIMIT 16382 > + > +// Max possible value is -256 to +256 but datasheet indicated -40 to 125. > +#define MAX_TEMP_LIMIT 125000 > +#define MIN_TEMP_LIMIT -40000 > + > +#define MAX_TEMP_HYST 127500 > + > +static const u8 TMP51X_TEMP_INPUT[4] = { > + TMP51X_LOCAL_TEMP_RESULT, > + TMP51X_REMOTE_TEMP_RESULT_1, > + TMP51X_REMOTE_TEMP_RESULT_2, > + TMP513_REMOTE_TEMP_RESULT_3 > +}; > + > +static const u8 TMP51X_TEMP_CRIT[4] = { > + TMP51X_LOCAL_TEMP_LIMIT, > + TMP51X_REMOTE_TEMP_LIMIT_1, > + TMP51X_REMOTE_TEMP_LIMIT_2, > + TMP513_REMOTE_TEMP_LIMIT_3 > +}; > + > +static const u8 TMP51X_TEMP_CRIT_ALARM[4] = { > + TMP51X_LOCAL_TEMP_LIMIT_POS, > + TMP51X_REMOTE_TEMP_LIMIT_1_POS, > + TMP51X_REMOTE_TEMP_LIMIT_2_POS, > + TMP513_REMOTE_TEMP_LIMIT_3_POS > +}; > + > +static const u8 TMP51X_TEMP_CRIT_HYST[4] = { > + TMP51X_N_FACTOR_AND_HYST_1, > + TMP51X_N_FACTOR_AND_HYST_1, > + TMP51X_N_FACTOR_AND_HYST_1, > + TMP51X_N_FACTOR_AND_HYST_1 > +}; > + > +static const u8 TMP51X_CURR_INPUT[2] = { > + TMP51X_SHUNT_CURRENT_RESULT, > + TMP51X_BUS_CURRENT_RESULT > +}; > + > +static struct regmap_config tmp51x_regmap_config = { > + .reg_bits = 8, > + .val_bits = 16, > + .max_register = TMP51X_MAX_REGISTER_ADDR, > +}; > + > +enum tmp51x_ids { > + tmp512, tmp513 > +}; > + > +struct tmp51x_data { > + u16 shunt_config; > + u16 pga_gain; > + u32 vbus_range_uvolt; > + > + u16 temp_config; > + u32 nfactor[3]; > + > + u32 shunt_uohms; > + > + u32 curr_lsb_ua; > + u32 pwr_lsb_uw; > + > + enum tmp51x_ids id; > + struct regmap *regmap; > +}; > + > +// Set the shift based on the gain 8=4, 4=3, 2=2, 1=1 > +static inline u8 tmp51x_get_pga_shift(struct tmp51x_data *data) > +{ > + return 5 - ffs(data->pga_gain); > +} > + > +static int tmp51x_get_value(struct tmp51x_data *data, u8 reg, u8 pos, > + unsigned int regval, long *val) > +{ > + switch (reg) { > + case TMP51X_STATUS: > + *val = (regval >> pos) & 1; > + break; > + case TMP51X_SHUNT_CURRENT_RESULT: > + case TMP51X_SHUNT_CURRENT_H_LIMIT: > + case TMP51X_SHUNT_CURRENT_L_LIMIT: > + /* > + * The valus is read in voltage in the chip but reported as > + * current to the user. > + * 2's compliment number shifted by one to four depending > + * on the pga gain setting. 1lsb = 10uV > + */ > + *val = sign_extend32(regval, 17 - tmp51x_get_pga_shift(data)); > + *val = DIV_ROUND_CLOSEST(*val * 10000, data->shunt_uohms); > + break; > + case TMP51X_BUS_VOLTAGE_RESULT: > + case TMP51X_BUS_VOLTAGE_H_LIMIT: > + case TMP51X_BUS_VOLTAGE_L_LIMIT: > + // 1lsb = 4mV > + *val = (regval >> TMP51X_BUS_VOLTAGE_SHIFT) * 4; > + break; > + case TMP51X_POWER_RESULT: > + case TMP51X_POWER_LIMIT: > + // Power = (current * BusVoltage) / 5000 > + *val = regval * data->pwr_lsb_uw; > + break; > + case TMP51X_BUS_CURRENT_RESULT: > + // Current = (ShuntVoltage * CalibrationRegister) / 4096 > + *val = sign_extend32(regval, 16) * data->curr_lsb_ua; > + *val = DIV_ROUND_CLOSEST(*val, 1000); > + break; > + case TMP51X_LOCAL_TEMP_RESULT: > + case TMP51X_REMOTE_TEMP_RESULT_1: > + case TMP51X_REMOTE_TEMP_RESULT_2: > + case TMP513_REMOTE_TEMP_RESULT_3: > + case TMP51X_LOCAL_TEMP_LIMIT: > + case TMP51X_REMOTE_TEMP_LIMIT_1: > + case TMP51X_REMOTE_TEMP_LIMIT_2: > + case TMP513_REMOTE_TEMP_LIMIT_3: > + // 1lsb = 0.0625 degrees centigrade > + *val = sign_extend32(regval, 16) >> TMP51X_TEMP_SHIFT; > + *val = DIV_ROUND_CLOSEST(*val * 625, 10); > + break; > + case TMP51X_N_FACTOR_AND_HYST_1: > + // 1lsb = 0.5 degrees centigrade > + *val = (regval & TMP51X_HYST_MASK) * 500; > + break; > + default: > + // Programmer goofed > + WARN_ON_ONCE(1); > + *val = 0; > + return -EOPNOTSUPP; > + } > + > + return 0; > +} > + > +static int tmp51x_set_value(struct tmp51x_data *data, u8 reg, long val) > +{ > + int regval, max_val; > + u32 mask = 0; > + > + switch (reg) { > + case TMP51X_SHUNT_CURRENT_H_LIMIT: > + case TMP51X_SHUNT_CURRENT_L_LIMIT: > + /* > + * The user enter current value and we convert it to > + * voltage. 1lsb = 10uV > + */ > + val = DIV_ROUND_CLOSEST(val * data->shunt_uohms, 10000); > + max_val = U16_MAX >> tmp51x_get_pga_shift(data); > + regval = clamp_val(val, -max_val, max_val); > + break; > + case TMP51X_BUS_VOLTAGE_H_LIMIT: > + case TMP51X_BUS_VOLTAGE_L_LIMIT: > + // 1lsb = 4mV > + max_val = (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_32V) ? > + MAX_BUS_VOLTAGE_32_LIMIT : MAX_BUS_VOLTAGE_16_LIMIT; > + > + val = clamp_val(DIV_ROUND_CLOSEST(val, 4), 0, max_val); > + regval = val << TMP51X_BUS_VOLTAGE_SHIFT; > + break; > + case TMP51X_POWER_LIMIT: > + regval = clamp_val(DIV_ROUND_CLOSEST(val, data->pwr_lsb_uw), 0, > + U16_MAX); > + break; > + case TMP51X_LOCAL_TEMP_LIMIT: > + case TMP51X_REMOTE_TEMP_LIMIT_1: > + case TMP51X_REMOTE_TEMP_LIMIT_2: > + case TMP513_REMOTE_TEMP_LIMIT_3: > + // 1lsb = 0.0625 degrees centigrade > + val = clamp_val(val, MIN_TEMP_LIMIT, MAX_TEMP_LIMIT); > + regval = DIV_ROUND_CLOSEST(val * 10, 625) << TMP51X_TEMP_SHIFT; > + break; > + case TMP51X_N_FACTOR_AND_HYST_1: > + // 1lsb = 0.5 degrees centigrade > + val = clamp_val(val, 0, MAX_TEMP_HYST); > + regval = DIV_ROUND_CLOSEST(val, 500); > + mask = TMP51X_HYST_MASK; > + break; > + default: > + // Programmer goofed > + WARN_ON_ONCE(1); > + return -EOPNOTSUPP; > + } > + > + if (mask == 0) > + return regmap_write(data->regmap, reg, regval); > + else > + return regmap_update_bits(data->regmap, reg, mask, regval); > +} > + > +static u8 tmp51x_get_reg(enum hwmon_sensor_types type, u32 attr, int channel) > +{ > + switch (type) { > + case hwmon_temp: > + switch (attr) { > + case hwmon_temp_input: > + return TMP51X_TEMP_INPUT[channel]; > + case hwmon_temp_crit_alarm: > + return TMP51X_STATUS; > + case hwmon_temp_crit: > + return TMP51X_TEMP_CRIT[channel]; > + case hwmon_temp_crit_hyst: > + return TMP51X_TEMP_CRIT_HYST[channel]; > + } > + break; > + case hwmon_in: > + switch (attr) { > + case hwmon_in_input: > + return TMP51X_BUS_VOLTAGE_RESULT; > + case hwmon_in_lcrit_alarm: > + case hwmon_in_crit_alarm: > + return TMP51X_STATUS; > + case hwmon_in_lcrit: > + return TMP51X_BUS_VOLTAGE_L_LIMIT; > + case hwmon_in_crit: > + return TMP51X_BUS_VOLTAGE_H_LIMIT; > + } > + break; > + case hwmon_curr: > + switch (attr) { > + case hwmon_curr_input: > + return TMP51X_CURR_INPUT[channel]; > + case hwmon_curr_lcrit_alarm: > + case hwmon_curr_crit_alarm: > + return TMP51X_STATUS; > + case hwmon_curr_lcrit: > + return TMP51X_SHUNT_CURRENT_L_LIMIT; > + case hwmon_curr_crit: > + return TMP51X_SHUNT_CURRENT_H_LIMIT; > + } > + break; > + case hwmon_power: > + switch (attr) { > + case hwmon_power_input: > + return TMP51X_POWER_RESULT; > + case hwmon_power_crit_alarm: > + return TMP51X_STATUS; > + case hwmon_power_crit: > + return TMP51X_POWER_LIMIT; > + } > + break; > + default: > + break; > + } > + > + return 0; > +} > + > +static u8 tmp51x_get_status_pos(enum hwmon_sensor_types type, u32 attr, > + int channel) > +{ > + switch (type) { > + case hwmon_temp: > + switch (attr) { > + case hwmon_temp_crit_alarm: > + return TMP51X_TEMP_CRIT_ALARM[channel]; > + } > + break; > + case hwmon_in: > + switch (attr) { > + case hwmon_in_lcrit_alarm: > + return TMP51X_BUS_VOLTAGE_L_LIMIT_POS; > + case hwmon_in_crit_alarm: > + return TMP51X_BUS_VOLTAGE_H_LIMIT_POS; > + } > + break; > + case hwmon_curr: > + switch (attr) { > + case hwmon_curr_lcrit_alarm: > + return TMP51X_SHUNT_CURRENT_L_LIMIT_POS; > + case hwmon_curr_crit_alarm: > + return TMP51X_SHUNT_CURRENT_H_LIMIT_POS; > + } > + break; > + case hwmon_power: > + switch (attr) { > + case hwmon_power_crit_alarm: > + return TMP51X_POWER_LIMIT_POS; > + } > + break; > + default: > + break; > + } > + > + return 0; > +} > + > +static int tmp51x_read(struct device *dev, enum hwmon_sensor_types type, > + u32 attr, int channel, long *val) > +{ > + struct tmp51x_data *data = dev_get_drvdata(dev); > + int ret; > + u32 regval; > + u8 pos = 0, reg = 0; > + > + reg = tmp51x_get_reg(type, attr, channel); > + if (reg == 0) > + return -EOPNOTSUPP; > + > + if (reg == TMP51X_STATUS) > + pos = tmp51x_get_status_pos(type, attr, channel); > + > + ret = regmap_read(data->regmap, reg, ®val); > + if (ret < 0) > + return ret; > + > + return tmp51x_get_value(data, reg, pos, regval, val); > +} > + > +static int tmp51x_write(struct device *dev, enum hwmon_sensor_types type, > + u32 attr, int channel, long val) > +{ > + u8 reg = 0; > + > + reg = tmp51x_get_reg(type, attr, channel); > + if (reg == 0) > + return -EOPNOTSUPP; > + > + return tmp51x_set_value(dev_get_drvdata(dev), reg, val); > +} > + > +static umode_t tmp51x_is_visible(const void *_data, > + enum hwmon_sensor_types type, u32 attr, > + int channel) > +{ > + const struct tmp51x_data *data = _data; > + > + switch (type) { > + case hwmon_temp: > + if (data->id == tmp512 && channel == 4) > + return 0; > + switch (attr) { > + case hwmon_temp_input: > + case hwmon_temp_crit_alarm: > + return 0444; > + case hwmon_temp_crit: > + return 0644; > + case hwmon_temp_crit_hyst: > + if (channel == 0) > + return 0644; > + return 0444; > + } > + break; > + case hwmon_in: > + switch (attr) { > + case hwmon_in_input: > + case hwmon_in_lcrit_alarm: > + case hwmon_in_crit_alarm: > + return 0444; > + case hwmon_in_lcrit: > + case hwmon_in_crit: > + return 0644; > + } > + break; > + case hwmon_curr: > + if (!data->shunt_uohms) > + return 0; > + > + switch (attr) { > + case hwmon_curr_input: > + case hwmon_curr_lcrit_alarm: > + case hwmon_curr_crit_alarm: > + return 0444; > + case hwmon_curr_lcrit: > + case hwmon_curr_crit: > + return 0644; > + } > + break; > + case hwmon_power: > + if (!data->shunt_uohms) > + return 0; > + > + switch (attr) { > + case hwmon_power_input: > + case hwmon_power_crit_alarm: > + return 0444; > + case hwmon_power_crit: > + return 0644; > + } > + break; > + default: > + break; > + } > + return 0; > +} > + > +static const struct hwmon_channel_info *tmp51x_info[] = { > + HWMON_CHANNEL_INFO(temp, > + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM | > + HWMON_T_CRIT_HYST, > + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM | > + HWMON_T_CRIT_HYST, > + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM | > + HWMON_T_CRIT_HYST, > + HWMON_T_INPUT | HWMON_T_CRIT | HWMON_T_CRIT_ALARM | > + HWMON_T_CRIT_HYST), > + HWMON_CHANNEL_INFO(in, > + HWMON_I_INPUT | HWMON_I_LCRIT | HWMON_I_LCRIT_ALARM | > + HWMON_I_CRIT | HWMON_I_CRIT_ALARM), > + HWMON_CHANNEL_INFO(curr, > + HWMON_C_INPUT | HWMON_C_LCRIT | HWMON_C_LCRIT_ALARM | > + HWMON_C_CRIT | HWMON_C_CRIT_ALARM, > + HWMON_C_INPUT), > + HWMON_CHANNEL_INFO(power, > + HWMON_P_INPUT | HWMON_P_CRIT | HWMON_P_CRIT_ALARM), > + NULL > +}; > + > +static const struct hwmon_ops tmp51x_hwmon_ops = { > + .is_visible = tmp51x_is_visible, > + .read = tmp51x_read, > + .write = tmp51x_write, > +}; > + > +static const struct hwmon_chip_info tmp51x_chip_info = { > + .ops = &tmp51x_hwmon_ops, > + .info = tmp51x_info, > +}; > + > +/* > + * Calibrate the tmp51x following the datasheet method > + */ > +static int tmp51x_calibrate(struct tmp51x_data *data) > +{ > + int vshunt_max = data->pga_gain * 40; > + u64 max_curr_ma; > + u32 div; > + > + /* > + * If shunt_uohms is equal to 0, the calibration should be set to 0. > + * The consequence will be that the current and power measurement engine > + * of the sensor will not work. Temperature and voltage sensing will > + * continue to work. > + */ > + if (data->shunt_uohms == 0) > + return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION, 0); > + > + max_curr_ma = DIV_ROUND_CLOSEST_ULL(vshunt_max * 1000 * 1000, > + data->shunt_uohms); > + > + /* > + * Calculate the minimal bit resolution for the current and the power. > + * Those values will be used during register interpretation. > + */ > + data->curr_lsb_ua = DIV_ROUND_CLOSEST_ULL(max_curr_ma * 1000, 32767); > + data->pwr_lsb_uw = 20 * data->curr_lsb_ua; > + > + div = DIV_ROUND_CLOSEST_ULL(data->curr_lsb_ua * data->shunt_uohms, > + 1000 * 1000); > + > + return regmap_write(data->regmap, TMP51X_SHUNT_CALIBRATION, > + DIV_ROUND_CLOSEST(40960, div)); > +} > + > +/* > + * Initialize the configuration and calibration registers. > + */ > +static int tmp51x_init(struct tmp51x_data *data) > +{ > + unsigned int regval; > + int ret = regmap_write(data->regmap, TMP51X_SHUNT_CONFIG, > + data->shunt_config); > + if (ret < 0) > + return ret; > + > + ret = regmap_write(data->regmap, TMP51X_TEMP_CONFIG, data->temp_config); > + if (ret < 0) > + return ret; > + > + // nFactor configuration > + ret = regmap_update_bits(data->regmap, TMP51X_N_FACTOR_AND_HYST_1, > + TMP51X_NFACTOR_MASK, data->nfactor[0] << 8); > + if (ret < 0) > + return ret; > + > + ret = regmap_write(data->regmap, TMP51X_N_FACTOR_2, > + data->nfactor[1] << 8); > + if (ret < 0) > + return ret; > + > + if (data->id == tmp513) { > + ret = regmap_write(data->regmap, TMP513_N_FACTOR_3, > + data->nfactor[2] << 8); > + if (ret < 0) > + return ret; > + } > + > + ret = tmp51x_calibrate(data); > + if (ret < 0) > + return ret; > + > + // Read the status register before using as the datasheet propose > + return regmap_read(data->regmap, TMP51X_STATUS, ®val); > +} > + > +static const struct i2c_device_id tmp51x_id[] = { > + { "tmp512", tmp512 }, > + { "tmp513", tmp513 }, > + { } > +}; > +MODULE_DEVICE_TABLE(i2c, tmp51x_id); > + > +static const struct of_device_id tmp51x_of_match[] = { > + { > + .compatible = "ti,tmp512", > + .data = (void *)tmp512 > + }, > + { > + .compatible = "ti,tmp513", > + .data = (void *)tmp513 > + }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, tmp51x_of_match); > + > +static int tmp51x_vbus_range_to_reg(struct device *dev, > + struct tmp51x_data *data) > +{ > + if (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_32V) { > + data->shunt_config |= TMP51X_BUS_VOLTAGE_MASK; > + } else if (data->vbus_range_uvolt == TMP51X_VBUS_RANGE_16V) { > + data->shunt_config &= ~TMP51X_BUS_VOLTAGE_MASK; > + } else { > + dev_err(dev, "ti,bus-range-microvolt is invalid: %u\n", > + data->vbus_range_uvolt); > + return -EINVAL; > + } > + return 0; > +} > + > +static int tmp51x_pga_gain_to_reg(struct device *dev, struct tmp51x_data *data) > +{ > + if (data->pga_gain == 8) { > + data->shunt_config |= CURRENT_SENSE_VOLTAGE_320_MASK; > + } else if (data->pga_gain == 4) { > + data->shunt_config |= CURRENT_SENSE_VOLTAGE_160_MASK; > + } else if (data->pga_gain == 2) { > + data->shunt_config |= CURRENT_SENSE_VOLTAGE_80_MASK; > + } else if (data->pga_gain == 1) { > + data->shunt_config |= CURRENT_SENSE_VOLTAGE_40_MASK; > + } else { > + dev_err(dev, "ti,pga-gain is invalid: %u\n", data->pga_gain); > + return -EINVAL; > + } > + return 0; > +} > + > +static int tmp51x_read_properties(struct device *dev, struct tmp51x_data *data) > +{ > + int ret; > + u32 nfactor[3]; > + u32 val; > + > + ret = device_property_read_u32(dev, "shunt-resistor-micro-ohms", &val); > + data->shunt_uohms = (ret >= 0) ? val : TMP51X_SHUNT_VALUE_DEFAULT; > + > + ret = device_property_read_u32(dev, "ti,bus-range-microvolt", &val); > + data->vbus_range_uvolt = (ret >= 0) ? val : TMP51X_VBUS_RANGE_DEFAULT; > + ret = tmp51x_vbus_range_to_reg(dev, data); > + if (ret < 0) > + return ret; > + > + ret = device_property_read_u32(dev, "ti,pga-gain", &val); > + data->pga_gain = (ret >= 0) ? val : TMP51X_PGA_DEFAULT; > + ret = tmp51x_pga_gain_to_reg(dev, data); > + if (ret < 0) > + return ret; > + > + ret = device_property_read_u32_array(dev, "ti,nfactor", nfactor, > + (data->id == tmp513) ? 3 : 2); > + if (ret >= 0) > + memcpy(data->nfactor, nfactor, (data->id == tmp513) ? 3 : 2); > + > + // Check if shunt value is compatible with pga-gain > + if (data->shunt_uohms > data->pga_gain * 40 * 1000 * 1000) { > + dev_err(dev, "shunt-resistor: %u too big for pga_gain: %u\n", > + data->shunt_uohms, data->pga_gain); > + return -EINVAL; > + } > + > + return 0; > +} > + > +static void tmp51x_use_default(struct tmp51x_data *data) > +{ > + data->vbus_range_uvolt = TMP51X_VBUS_RANGE_DEFAULT; > + data->pga_gain = TMP51X_PGA_DEFAULT; > + data->shunt_uohms = TMP51X_SHUNT_VALUE_DEFAULT; > +} > + > +static int tmp51x_configure(struct device *dev, struct tmp51x_data *data) > +{ > + data->shunt_config = TMP51X_SHUNT_CONFIG_DEFAULT; > + data->temp_config = (data->id == tmp513) ? > + TMP513_TEMP_CONFIG_DEFAULT : TMP512_TEMP_CONFIG_DEFAULT; > + > + if (dev->of_node) > + return tmp51x_read_properties(dev, data); > + > + tmp51x_use_default(data); > + > + return 0; > +} > + > +static int tmp51x_probe(struct i2c_client *client, > + const struct i2c_device_id *id) > +{ > + struct device *dev = &client->dev; > + struct tmp51x_data *data; > + struct device *hwmon_dev; > + int ret; > + > + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); > + if (!data) > + return -ENOMEM; > + > + if (client->dev.of_node) > + data->id = (enum tmp51x_ids)device_get_match_data(&client->dev); > + else > + data->id = id->driver_data; > + > + ret = tmp51x_configure(dev, data); > + if (ret < 0) { > + dev_err(dev, "error configuring the device: %d\n", ret); > + return ret; > + } > + > + data->regmap = devm_regmap_init_i2c(client, &tmp51x_regmap_config); > + if (IS_ERR(data->regmap)) { > + dev_err(dev, "failed to allocate register map\n"); > + return PTR_ERR(data->regmap); > + } > + > + ret = tmp51x_init(data); > + if (ret < 0) { > + dev_err(dev, "error configuring the device: %d\n", ret); > + return -ENODEV; > + } > + > + hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, > + data, > + &tmp51x_chip_info, > + NULL); > + if (IS_ERR(hwmon_dev)) > + return PTR_ERR(hwmon_dev); > + > + dev_dbg(dev, "power monitor %s\n", id->name); > + > + return 0; > +} > + > +static struct i2c_driver tmp51x_driver = { > + .driver = { > + .name = "tmp51x", > + .of_match_table = of_match_ptr(tmp51x_of_match), > + }, > + .probe = tmp51x_probe, > + .id_table = tmp51x_id, > +}; > + > +module_i2c_driver(tmp51x_driver); > + > +MODULE_AUTHOR("Eric Tremblay <etremblay@xxxxxxxxxxxxxxxxxxx>"); > +MODULE_DESCRIPTION("tmp51x driver"); > +MODULE_LICENSE("GPL");
