> -----Original Message----- > From: Strashko, Grygorii > Sent: Thursday, November 21, 2019 5:05 AM > To: Robey, Caleb; linux-omap@xxxxxxxxxxxxxxx > Cc: Jason Kridner; Vutla, Lokesh; Kridner, Jason; Rizvi, Mohammad Faiz > Abbas; Dannenberg, Andreas; Hiblot, Jean-Jacques; Bajjuri, Praneeth; Davis, > Andrew; Tom Rini; Robert Nelson; Rob Herring; Mark Rutland; Benoît > Cousson; Tony Lindgren; devicetree@xxxxxxxxxxxxxxx; linux- > kernel@xxxxxxxxxxxxxxx > Subject: Re: [PATCH 1/1] ARM: dts: am5729: beaglebone-ai: adding device > tree > > > > On 19/11/2019 22:28, Caleb Robey wrote: > > From: Jason Kridner <jdk@xxxxxx> > > > > BeagleBoard.org BeagleBone AI is an open source hardware single > > board computer based on the Texas Instruments AM5729 SoC featuring > > dual-core 1.5GHz Arm Cortex-A15 processor, dual-core C66 digital > > signal processor (DSP), quad-core embedded vision engine (EVE), > > Arm Cortex-M4 processors, dual programmable realtime unit > > industrial control subsystems and more. The board features 1GB > > DDR3L, USB3.0 Type-C, USB HS Type-A, microHDMI, 16GB eMMC flash, > > 1G Ethernet, 802.11ac 2/5GHz, Bluetooth, and BeagleBone expansion > > headers. > > > > For more information, refer to: > > https://beaglebone.ai > > > > > > This patch introduces the BeagleBone AI device tree. > > > > Note that the device use the "ti,tpd12s016" component which is > > software compatible with "ti,tpd12s015". Thus we only use the > > latter driver. > > > > Signed-off-by: Jason Kridner <jdk@xxxxxx> > > Signed-off-by: Caleb Robey <c-robey@xxxxxx> > > Cc: Robert Nelson <robertcnelson@xxxxxxxxx> > > > > --- > > arch/arm/boot/dts/Makefile | 1 + > > arch/arm/boot/dts/am5729-beagleboneai.dts | 782 > ++++++++++++++++++++++ > > 2 files changed, 783 insertions(+) > > create mode 100644 arch/arm/boot/dts/am5729-beagleboneai.dts > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index b21b3a64641a..b1154dbda73c 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > [..] > > > + > > +&uart1 { > > + status = "okay"; > > +}; > > + > > +&davinci_mdio { > > + reset-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; > > + reset-delay-us = <2>; > > + > > + phy0: ethernet-phy@1 { > > + reg = <4>; > > + compatible = "ethernet-phy-id004d.d072", > > + "ethernet-phy-ieee802.3-c22"; > > Pls, do not ignore my comments. > > Above compatible should not be required. Grygori, I am so sorry about this - I had deleted this, but must have made a mistake in the resubmission. I will fix it immediately. > > > + eee-broken-100tx; > > + eee-broken-1000t; > > + }; > > +}; > > + > > +&mac { > > + slaves = <1>; > > + status = "okay"; > > +}; > > Pls, move cpsw node here Same as above... this must be the wrong file. I apologize. > > > + > > +&ocp { > > + pruss1_shmem: pruss_shmem@4b200000 { > > + status = "okay"; > > + compatible = "ti,pruss-shmem"; > > + reg = <0x4b200000 0x020000>; > > + }; > > + > > [..] > > > + > > +&cpsw_emac0 { > > + phy-handle = <&phy0>; > > + phy-mode = "rgmii"; > > +}; > > Move it up, pls. > > -- > Best regards, > grygorii
