Hello Jacopo,
On Fri, Nov 08, 2019 at 10:39:27AM +0100, Jacopo Mondi wrote:
> On Fri, Nov 08, 2019 at 09:22:56AM +0000, Fabrizio Castro wrote:
> > On 07 November 2019 20:35 Laurent Pinchart wrote:
> > > On Thu, Nov 07, 2019 at 08:10:58PM +0000, Fabrizio Castro wrote:
> > > > lvds-encoder.c implementation is also suitable for LVDS decoders,
> > > > not just LVDS encoders.
> > > > Instead of creating a new driver for addressing support for
> > > > transparent LVDS decoders, repurpose lvds-encoder.c for the greater
> > > > good.
> > > >
> > > > Signed-off-by: Fabrizio Castro <fabrizio.castro@xxxxxxxxxxxxxx>
> > > >
> > > > ---
> > > > v2->v3:
> > > > * No change
> > > > v1->v2:
> > > > * No change
> > > > ---
> > > > drivers/gpu/drm/bridge/Kconfig | 8 +-
> > > > drivers/gpu/drm/bridge/Makefile | 2 +-
> > > > drivers/gpu/drm/bridge/lvds-codec.c | 131 ++++++++++++++++++++++++++++
> > > > drivers/gpu/drm/bridge/lvds-encoder.c | 155 ----------------------------------
> > > > 4 files changed, 136 insertions(+), 160 deletions(-)
> > >
> > > It would help if you added the -M1 option to git-format-patch to detect
> > > the rename, the result would be easier to review.
> >
> > Will do, thank you for the hint
> >
> > > > create mode 100644 drivers/gpu/drm/bridge/lvds-codec.c
> > > > delete mode 100644 drivers/gpu/drm/bridge/lvds-encoder.c
> > > >
> > > > diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> > > > index 3436297..9e75ca4e 100644
> > > > --- a/drivers/gpu/drm/bridge/Kconfig
> > > > +++ b/drivers/gpu/drm/bridge/Kconfig
> > > > @@ -45,14 +45,14 @@ config DRM_DUMB_VGA_DAC
> > > > Support for non-programmable RGB to VGA DAC bridges, such as ADI
> > > > ADV7123, TI THS8134 and THS8135 or passive resistor ladder DACs.
> > > >
> > > > -config DRM_LVDS_ENCODER
> > > > - tristate "Transparent parallel to LVDS encoder support"
> > > > +config DRM_LVDS_CODEC
> > > > + tristate "Transparent LVDS encoders and decoders support"
> > > > depends on OF
> > > > select DRM_KMS_HELPER
> > > > select DRM_PANEL_BRIDGE
> > > > help
> > > > - Support for transparent parallel to LVDS encoders that don't require
> > > > - any configuration.
> > > > + Support for transparent LVDS encoders and LVDS decoders that don't
> > > > + require any configuration.
> > > >
> > > > config DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW
> > > > tristate "MegaChips stdp4028-ge-b850v3-fw and stdp2690-ge-b850v3-fw"
> > > > diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> > > > index 4934fcf..8a9178a 100644
> > > > --- a/drivers/gpu/drm/bridge/Makefile
> > > > +++ b/drivers/gpu/drm/bridge/Makefile
> > > > @@ -2,7 +2,7 @@
> > > > obj-$(CONFIG_DRM_ANALOGIX_ANX78XX) += analogix-anx78xx.o
> > > > obj-$(CONFIG_DRM_CDNS_DSI) += cdns-dsi.o
> > > > obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> > > > -obj-$(CONFIG_DRM_LVDS_ENCODER) += lvds-encoder.o
> > > > +obj-$(CONFIG_DRM_LVDS_CODEC) += lvds-codec.o
> > > > obj-$(CONFIG_DRM_MEGACHIPS_STDPXXXX_GE_B850V3_FW) += megachips-stdpxxxx-ge-b850v3-fw.o
> > > > obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> > > > obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> > > > diff --git a/drivers/gpu/drm/bridge/lvds-codec.c b/drivers/gpu/drm/bridge/lvds-codec.c
> > > > new file mode 100644
> > > > index 0000000..d57a8eb
> > > > --- /dev/null
> > > > +++ b/drivers/gpu/drm/bridge/lvds-codec.c
> > > > @@ -0,0 +1,131 @@
> > > > +// SPDX-License-Identifier: GPL-2.0-or-later
> > > > +/*
> > > > + * Copyright (C) 2019 Renesas Electronics Corporation
> > > > + * Copyright (C) 2016 Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > > > + */
> > > > +
> > > > +#include <linux/gpio/consumer.h>
> > > > +#include <linux/module.h>
> > > > +#include <linux/of.h>
> > > > +#include <linux/of_device.h>
> > > > +#include <linux/of_graph.h>
> > > > +#include <linux/platform_device.h>
> > > > +
> > > > +#include <drm/drm_bridge.h>
> > > > +#include <drm/drm_panel.h>
> > > > +
> > > > +struct lvds_codec {
> > > > + struct drm_bridge bridge;
> > > > + struct drm_bridge *panel_bridge;
> > > > + struct gpio_desc *powerdown_gpio;
> > > > +};
> > > > +
> > > > +static int lvds_codec_attach(struct drm_bridge *bridge)
> > > > +{
> > > > + struct lvds_codec *lvds_codec = container_of(bridge,
> > > > + struct lvds_codec, bridge);
> > > > +
> > > > + return drm_bridge_attach(bridge->encoder, lvds_codec->panel_bridge,
> > > > + bridge);
> > > > +}
> > > > +
> > > > +static void lvds_codec_enable(struct drm_bridge *bridge)
> > > > +{
> > > > + struct lvds_codec *lvds_codec = container_of(bridge,
> > > > + struct lvds_codec, bridge);
> > > > +
> > > > + if (lvds_codec->powerdown_gpio)
> > > > + gpiod_set_value_cansleep(lvds_codec->powerdown_gpio, 0);
> > > > +}
> > > > +
> > > > +static void lvds_codec_disable(struct drm_bridge *bridge)
> > > > +{
> > > > + struct lvds_codec *lvds_codec = container_of(bridge,
> > > > + struct lvds_codec, bridge);
> > > > +
> > > > + if (lvds_codec->powerdown_gpio)
> > > > + gpiod_set_value_cansleep(lvds_codec->powerdown_gpio, 1);
> > > > +}
> > > > +
> > > > +static struct drm_bridge_funcs funcs = {
> > > > + .attach = lvds_codec_attach,
> > > > + .enable = lvds_codec_enable,
> > > > + .disable = lvds_codec_disable,
> > > > +};
> > > > +
> > > > +static int lvds_codec_probe(struct platform_device *pdev)
> > > > +{
> > > > + struct device *dev = &pdev->dev;
> > > > + struct device_node *panel_node;
> > > > + struct drm_panel *panel;
> > > > + struct lvds_codec *lvds_codec;
> > > > +
> > > > + lvds_codec = devm_kzalloc(dev, sizeof(*lvds_codec), GFP_KERNEL);
> > > > + if (!lvds_codec)
> > > > + return -ENOMEM;
> > > > +
> > > > + lvds_codec->powerdown_gpio = devm_gpiod_get_optional(dev, "powerdown",
> > > > + GPIOD_OUT_HIGH);
> > > > + if (IS_ERR(lvds_codec->powerdown_gpio))
> > > > + return PTR_ERR(lvds_codec->powerdown_gpio);
> > >
> > > The driver had an error message here, any reason it got removed ?
> >
> > I am quoting from https://www.spinics.net/lists/devicetree/msg318602.html :
> > "I know it was there already, but this seems a bit unusual for the
> > minimal gain of having a printout in the very unlikely case the
> > gpiod_get() operations fails. I would just return PTR_ERR()."
> >
> > I am OK with reinstating it, just let me know what you want me to do here.
>
> Yeah, I suggested that as it seemed to me quite unusual pattern for the
> minimal gain of having an error message in an unlikely case. Sorry Fab
> for the double effort if Laurent wants it back again.
>
> > > > +
> > > > + panel_node = of_graph_get_remote_node(dev->of_node, 1, 0);
> > > > + if (!panel_node) {
> > > > + dev_dbg(dev, "panel DT node not found\n");
> > > > + return -ENXIO;
> > > > + }
> > > > +
> > > > + panel = of_drm_find_panel(panel_node);
> > > > + of_node_put(panel_node);
> > > > + if (IS_ERR(panel)) {
> > > > + dev_dbg(dev, "panel not found, deferring probe\n");
> > > > + return PTR_ERR(panel);
> > > > + }
> > > > +
> > > > + lvds_codec->panel_bridge = devm_drm_panel_bridge_add(dev, panel);
> > >
> > > This was devm_drm_panel_bridge_add_typed(), do you think there's a risk
> > > of breaking userspace ? Of course as noted in the documentation of
> > > devm_drm_panel_bridge_add_typed() the right solution is to fix panel
> > > drivers, but I'm still slightly worried.
> >
> > Things break when the panel doesn't define connector_type, leading to the below
> > check from devm_drm_panel_bridge_add:
> > if (WARN_ON(panel->connector_type == DRM_MODE_CONNECTOR_Unknown))
> > return NULL;
> >
> > Please advise on the best course of action here.
>
> I pointed out that function was described as deprecated and probably
> fixing the panel driver would be best. Why are you concerned about
> userspace ? is the panel driver that should correctly report its
> connector type, isn't it ? In case it's not, sorry again Fab for the
> double effort.
I'm concerned that this change may turn a working system in a
non-working system. The issue has to be fixed in panel drivers of
course, but switching from devm_drm_panel_bridge_add_typed() to
devm_drm_panel_bridge_add() should only be done once all the drivers
that are used with lvds-encoder behave properly.
> > > Actually, could you split this patch in two, with a patch that only
> > > renames the driver (and the symbols internally) without any functional
> > > change, and another patch that performs the modifications ? That would
> > > be much easier to review and discuss.
>
> This is more work for something that could be simply addressed by the
> reviewer by passing -M10 to git show. For such a simple driver isn't
> this fine the way it is ?
Don't make it difficult for the reviewer. I've reviewed this patch in my
e-mail client, not in git. The patch itself should be generated with
-M10, but in any case, such renames should not be bundled with other
changes. One logical change by patch is the rule, and we can sometimes
bundle a semi-unrelated minor change (such as a typo or indentation
fix), but certainly not a potentially dangerous functional change that
needs to be carefully reviewed.
> > Will do
> >
> > > > + if (IS_ERR(lvds_codec->panel_bridge))
> > > > + return PTR_ERR(lvds_codec->panel_bridge);
> > > > +
> > > > + /* The panel_bridge bridge is attached to the panel's of_node,
> > > > + * but we need a bridge attached to our of_node for our user
> > > > + * to look up.
> > > > + */
> > > > + lvds_codec->bridge.of_node = dev->of_node;
> > > > + lvds_codec->bridge.funcs = &funcs;
> > > > + drm_bridge_add(&lvds_codec->bridge);
> > > > +
> > > > + platform_set_drvdata(pdev, lvds_codec);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static int lvds_codec_remove(struct platform_device *pdev)
> > > > +{
> > > > + struct lvds_codec *lvds_codec = platform_get_drvdata(pdev);
> > > > +
> > > > + drm_bridge_remove(&lvds_codec->bridge);
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static const struct of_device_id lvds_codec_match[] = {
> > > > + { .compatible = "lvds-encoder" },
> > > > + { .compatible = "thine,thc63lvdm83d" },
> > > > + { .compatible = "lvds-decoder" },
> > > > + {},
> > > > +};
> > > > +MODULE_DEVICE_TABLE(of, lvds_codec_match);
> > > > +
> > > > +static struct platform_driver lvds_codec_driver = {
> > > > + .probe = lvds_codec_probe,
> > > > + .remove = lvds_codec_remove,
> > > > + .driver = {
> > > > + .name = "lvds-codec",
> > > > + .of_match_table = lvds_codec_match,
> > > > + },
> > > > +};
> > > > +module_platform_driver(lvds_codec_driver);
> > > > +
> > > > +MODULE_AUTHOR("Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>");
> > > > +MODULE_DESCRIPTION("Driver for transparent LVDS encoders and LVDS decoders");
> > >
> > > Maybe "LVDS encoders and decoders" ?
> > >
> > > > +MODULE_LICENSE("GPL");
> > >
> > > [snip]
--
Regards,
Laurent Pinchart
