On Thu, Nov 07, 2019 at 06:37:01PM +0900, Tomasz Figa wrote:
> On Thu, Nov 7, 2019 at 6:29 PM Sakari Ailus
> <sakari.ailus@xxxxxxxxxxxxxxx> wrote:
> >
> > Hi Tomasz,
> >
> > On Thu, Nov 07, 2019 at 04:58:09PM +0900, Tomasz Figa wrote:
> > > On Wed, Nov 6, 2019 at 6:16 AM Sakari Ailus
> > > <sakari.ailus@xxxxxxxxxxxxxxx> wrote:
> > > >
> > > > Hi Dongchun,
> > > >
> > > > On Mon, Nov 04, 2019 at 06:57:13PM +0800, Dongchun Zhu wrote:
> > > > > Add a V4L2 sub-device driver for OV02A10 image sensor.
> > > > > The OV02A10 is a 1/5" CMOS sensor from Omnivision, supporting
> > > > > output format: 10-bit RAW.
> > > > >
> > > > > This chip has a single MIPI lane interface and use the I2C bus
> > > > > for control and the CSI-2 bus for data.
> > > > >
> > > > > Signed-off-by: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> > > > > ---
> > > > > MAINTAINERS | 1 +
> > > > > drivers/media/i2c/Kconfig | 12 +
> > > > > drivers/media/i2c/Makefile | 1 +
> > > > > drivers/media/i2c/ov02a10.c | 1113 +++++++++++++++++++++++++++++++++++++++++++
> > > > > 4 files changed, 1127 insertions(+)
> > > > > create mode 100644 drivers/media/i2c/ov02a10.c
> > > > >
> > > > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > > > index ca503fc..0ce4af9 100644
> > > > > --- a/MAINTAINERS
> > > > > +++ b/MAINTAINERS
> > > > > @@ -11954,6 +11954,7 @@ M: Dongchun Zhu <dongchun.zhu@xxxxxxxxxxxx>
> > > > > L: linux-media@xxxxxxxxxxxxxxx
> > > > > T: git git://linuxtv.org/media_tree.git
> > > > > S: Maintained
> > > > > +F: drivers/media/i2c/ov02a10.c
> > > > > F: Documentation/devicetree/bindings/media/i2c/ov02a10.txt
> > > > >
> > > > > OMNIVISION OV2680 SENSOR DRIVER
> > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > > > > index 7eee181..3be8c0e 100644
> > > > > --- a/drivers/media/i2c/Kconfig
> > > > > +++ b/drivers/media/i2c/Kconfig
> > > > > @@ -620,6 +620,18 @@ config VIDEO_IMX355
> > > > > To compile this driver as a module, choose M here: the
> > > > > module will be called imx355.
> > > > >
> > > > > +config VIDEO_OV02A10
> > > > > + tristate "OmniVision OV02A10 sensor support"
> > > > > + depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
> > > > > + depends on MEDIA_CAMERA_SUPPORT
> > > > > + select V4L2_FWNODE
> > > > > + help
> > > > > + This is a Video4Linux2 sensor driver for the OmniVision
> > > > > + OV02A10 camera sensor.
> > > > > +
> > > > > + To compile this driver as a module, choose M here: the
> > > > > + module will be called ov02a10.
> > > > > +
> > > > > config VIDEO_OV2640
> > > > > tristate "OmniVision OV2640 sensor support"
> > > > > depends on VIDEO_V4L2 && I2C
> > > > > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > > > > index beb170b..c0774d4 100644
> > > > > --- a/drivers/media/i2c/Makefile
> > > > > +++ b/drivers/media/i2c/Makefile
> > > > > @@ -63,6 +63,7 @@ obj-$(CONFIG_VIDEO_VP27SMPX) += vp27smpx.o
> > > > > obj-$(CONFIG_VIDEO_SONY_BTF_MPX) += sony-btf-mpx.o
> > > > > obj-$(CONFIG_VIDEO_UPD64031A) += upd64031a.o
> > > > > obj-$(CONFIG_VIDEO_UPD64083) += upd64083.o
> > > > > +obj-$(CONFIG_VIDEO_OV02A10) += ov02a10.o
> > > > > obj-$(CONFIG_VIDEO_OV2640) += ov2640.o
> > > > > obj-$(CONFIG_VIDEO_OV2680) += ov2680.o
> > > > > obj-$(CONFIG_VIDEO_OV2685) += ov2685.o
> > > > > diff --git a/drivers/media/i2c/ov02a10.c b/drivers/media/i2c/ov02a10.c
> > > > > new file mode 100644
> > > > > index 0000000..f1ed4eb
> > > > > --- /dev/null
> > > > > +++ b/drivers/media/i2c/ov02a10.c
> > > > > @@ -0,0 +1,1113 @@
> > > > > +// SPDX-License-Identifier: GPL-2.0
> > > > > +// Copyright (c) 2019 MediaTek Inc.
> > > > > +
> > > > > +#include <linux/clk.h>
> > > > > +#include <linux/delay.h>
> > > > > +#include <linux/device.h>
> > > > > +#include <linux/gpio/consumer.h>
> > > > > +#include <linux/i2c.h>
> > > > > +#include <linux/module.h>
> > > > > +#include <linux/pm_runtime.h>
> > > > > +#include <linux/regulator/consumer.h>
> > > > > +#include <media/media-entity.h>
> > > > > +#include <media/v4l2-async.h>
> > > > > +#include <media/v4l2-ctrls.h>
> > > > > +#include <media/v4l2-subdev.h>
> > > > > +#include <media/v4l2-fwnode.h>
> > > > > +
> > > > > +#define CHIP_ID 0x2509
> > > > > +#define OV02A10_REG_CHIP_ID_H 0x02
> > > > > +#define OV02A10_REG_CHIP_ID_L 0x03
> > > > > +#define OV02A10_ID(_msb, _lsb) ((_msb) << 8 | (_lsb))
> > > > > +
> > > > > +/* Bit[1] vertical upside down */
> > > > > +/* Bit[0] horizontal mirror */
> > > > > +#define REG_MIRROR_FLIP_CONTROL 0x3f
> > > > > +
> > > > > +/* Orientation */
> > > > > +#define REG_MIRROR_FLIP_ENABLE 0x03
> > > > > +
> > > > > +/* Bit[7] clock HS mode enable
> > > > > + * 0: Clock continue
> > > > > + * 1: Clock HS
> > > > > + * Bit[6:2] HS VOD adjust
> > > > > + * Bit[1:0] P VHI adjust
> > > > > + */
> > > > > +#define REG_HS_MODE_BLC 0x9d
> > > > > +
> > > > > +#define CLOCK_HS_MODE_ENABLE BIT(7)
> > > > > +#define CLOCK_HS_VOD_ADJUST (BIT(6) | BIT(5) | BIT(4) | BIT(3) | BIT(2))
> > > > > +
> > > > > +/* Bit[2:0] MIPI transmission speed select */
> > > > > +#define TX_SPEED_AREA_SEL 0xa1
> > > > > +
> > > > > +#define REG_PAGE_SWITCH 0xfd
> > > > > +#define REG_GLOBAL_EFFECTIVE 0x01
> > > > > +#define REG_ENABLE BIT(0)
> > > > > +#define OV02A10_MASK_8_BITS 0xff
> > > > > +
> > > > > +#define REG_SC_CTRL_MODE 0xac
> > > > > +#define SC_CTRL_MODE_STANDBY 0x00
> > > > > +#define SC_CTRL_MODE_STREAMING 0x01
> > > > > +
> > > > > +#define OV02A10_EXP_SHIFT 8
> > > > > +#define OV02A10_REG_EXPOSURE_H 0x03
> > > > > +#define OV02A10_REG_EXPOSURE_L 0x04
> > > > > +#define OV02A10_EXPOSURE_MIN 4
> > > > > +#define OV02A10_EXPOSURE_MAX_MARGIN 4
> > > > > +#define OV02A10_EXPOSURE_STEP 1
> > > > > +
> > > > > +#define OV02A10_VTS_SHIFT 8
> > > > > +#define OV02A10_REG_VTS_H 0x05
> > > > > +#define OV02A10_REG_VTS_L 0x06
> > > > > +#define OV02A10_VTS_MAX 0x209f
> > > > > +#define OV02A10_VTS_MIN 0x04cf
> > > > > +#define OV02A10_BASIC_LINE 1224
> > > > > +
> > > > > +#define OV02A10_REG_GAIN 0x24
> > > > > +#define OV02A10_GAIN_MIN 0x10
> > > > > +#define OV02A10_GAIN_MAX 0xf8
> > > > > +#define OV02A10_GAIN_STEP 0x01
> > > > > +#define OV02A10_GAIN_DEFAULT 0x40
> > > > > +
> > > > > +/* Test pattern control */
> > > > > +#define OV02A10_REG_TEST_PATTERN 0xb6
> > > > > +#define OV02A10_TEST_PATTERN_ENABLE BIT(0)
> > > > > +
> > > > > +#define OV02A10_LINK_FREQ_390MHZ 390000000ULL
> > > > > +#define OV02A10_ECLK_FREQ 24000000
> > > > > +#define OV02A10_DATA_LANES 1
> > > > > +#define OV02A10_BITS_PER_SAMPLE 10
> > > > > +
> > > > > +static const char * const ov02a10_supply_names[] = {
> > > > > + "dovdd", /* Digital I/O power */
> > > > > + "avdd", /* Analog power */
> > > > > + "dvdd", /* Digital core power */
> > > > > +};
> > > > > +
> > > > > +#define OV02A10_NUM_SUPPLIES ARRAY_SIZE(ov02a10_supply_names)
> > > > > +
> > > > > +struct ov02a10_reg {
> > > > > + u8 addr;
> > > > > + u8 val;
> > > > > +};
> > > > > +
> > > > > +struct ov02a10_reg_list {
> > > > > + u32 num_of_regs;
> > > > > + const struct ov02a10_reg *regs;
> > > > > +};
> > > > > +
> > > > > +struct ov02a10_mode {
> > > > > + u32 width;
> > > > > + u32 height;
> > > > > + u32 exp_def;
> > > > > + u32 hts_def;
> > > > > + u32 vts_def;
> > > > > + const struct ov02a10_reg_list reg_list;
> > > > > +};
> > > > > +
> > > > > +struct ov02a10 {
> > > > > + u32 eclk_freq;
> > > > > + u32 mipi_clock_tx_speed;
> > > > > + u32 mipi_clock_hs_vod_adjust_cnt;
> > > > > +
> > > > > + struct clk *eclk;
> > > > > + struct gpio_desc *pd_gpio;
> > > > > + struct gpio_desc *n_rst_gpio;
> > > > > + struct regulator_bulk_data supplies[OV02A10_NUM_SUPPLIES];
> > > > > +
> > > > > + bool streaming;
> > > > > + bool upside_down;
> > > > > + bool mipi_clock_hs_mode_enable;
> > > > > +
> > > > > + /*
> > > > > + * Serialize control access, get/set format, get selection
> > > > > + * and start streaming.
> > > > > + */
> > > > > + struct mutex mutex;
> > > > > + struct v4l2_subdev subdev;
> > > > > + struct media_pad pad;
> > > > > + struct v4l2_ctrl *anal_gain;
> > > > > + struct v4l2_ctrl *exposure;
> > > > > + struct v4l2_ctrl *hblank;
> > > > > + struct v4l2_ctrl *vblank;
> > > > > + struct v4l2_ctrl *test_pattern;
> > > > > + struct v4l2_mbus_framefmt fmt;
> > > > > + struct v4l2_ctrl_handler ctrl_handler;
> > > > > +
> > > > > + const struct ov02a10_mode *cur_mode;
> > > > > +};
> > > > > +
> > > > > +static inline struct ov02a10 *to_ov02a10(struct v4l2_subdev *sd)
> > > > > +{
> > > > > + return container_of(sd, struct ov02a10, subdev);
> > > > > +}
> > > > > +
> > > > > +/*
> > > > > + * eclk 24Mhz
> > > > > + * pclk 39Mhz
> > > > > + * linelength 934(0x3a6)
> > > > > + * framelength 1390(0x56E)
> > > > > + * grabwindow_width 1600
> > > > > + * grabwindow_height 1200
> > > > > + * max_framerate 30fps
> > > > > + * mipi_datarate per lane 780Mbps
> > > > > + */
> > > > > +static const struct ov02a10_reg ov02a10_1600x1200_regs[] = {
> > > > > + {0xfd, 0x01},
> > > > > + {0xac, 0x00},
> > > > > + {0xfd, 0x00},
> > > > > + {0x2f, 0x29},
> > > > > + {0x34, 0x00},
> > > > > + {0x35, 0x21},
> > > > > + {0x30, 0x15},
> > > > > + {0x33, 0x01},
> > > > > + {0xfd, 0x01},
> > > > > + {0x44, 0x00},
> > > > > + {0x2a, 0x4c},
> > > > > + {0x2b, 0x1e},
> > > > > + {0x2c, 0x60},
> > > > > + {0x25, 0x11},
> > > > > + {0x03, 0x01},
> > > > > + {0x04, 0xae},
> > > > > + {0x09, 0x00},
> > > > > + {0x0a, 0x02},
> > > > > + {0x06, 0xa6},
> > > > > + {0x31, 0x00},
> > > > > + {0x24, 0x40},
> > > > > + {0x01, 0x01},
> > > > > + {0xfb, 0x73},
> > > > > + {0xfd, 0x01},
> > > > > + {0x16, 0x04},
> > > > > + {0x1c, 0x09},
> > > > > + {0x21, 0x42},
> > > > > + {0x12, 0x04},
> > > > > + {0x13, 0x10},
> > > > > + {0x11, 0x40},
> > > > > + {0x33, 0x81},
> > > > > + {0xd0, 0x00},
> > > > > + {0xd1, 0x01},
> > > > > + {0xd2, 0x00},
> > > > > + {0x50, 0x10},
> > > > > + {0x51, 0x23},
> > > > > + {0x52, 0x20},
> > > > > + {0x53, 0x10},
> > > > > + {0x54, 0x02},
> > > > > + {0x55, 0x20},
> > > > > + {0x56, 0x02},
> > > > > + {0x58, 0x48},
> > > > > + {0x5d, 0x15},
> > > > > + {0x5e, 0x05},
> > > > > + {0x66, 0x66},
> > > > > + {0x68, 0x68},
> > > > > + {0x6b, 0x00},
> > > > > + {0x6c, 0x00},
> > > > > + {0x6f, 0x40},
> > > > > + {0x70, 0x40},
> > > > > + {0x71, 0x0a},
> > > > > + {0x72, 0xf0},
> > > > > + {0x73, 0x10},
> > > > > + {0x75, 0x80},
> > > > > + {0x76, 0x10},
> > > > > + {0x84, 0x00},
> > > > > + {0x85, 0x10},
> > > > > + {0x86, 0x10},
> > > > > + {0x87, 0x00},
> > > > > + {0x8a, 0x22},
> > > > > + {0x8b, 0x22},
> > > > > + {0x19, 0xf1},
> > > > > + {0x29, 0x01},
> > > > > + {0xfd, 0x01},
> > > > > + {0x9d, 0xd6},
> > > > > + {0xa0, 0x29},
> > > > > + {0xa1, 0x03},
> > > > > + {0xad, 0x62},
> > > > > + {0xae, 0x00},
> > > > > + {0xaf, 0x85},
> > > > > + {0xb1, 0x01},
> > > > > + {0x8e, 0x06},
> > > > > + {0x8f, 0x40},
> > > > > + {0x90, 0x04},
> > > > > + {0x91, 0xb0},
> > > > > + {0x45, 0x01},
> > > > > + {0x46, 0x00},
> > > > > + {0x47, 0x6c},
> > > > > + {0x48, 0x03},
> > > > > + {0x49, 0x8b},
> > > > > + {0x4a, 0x00},
> > > > > + {0x4b, 0x07},
> > > > > + {0x4c, 0x04},
> > > > > + {0x4d, 0xb7},
> > > > > + {0xf0, 0x40},
> > > > > + {0xf1, 0x40},
> > > > > + {0xf2, 0x40},
> > > > > + {0xf3, 0x40},
> > > > > + {0x3f, 0x00},
> > > > > + {0xfd, 0x01},
> > > > > + {0x05, 0x00},
> > > > > + {0x06, 0xa6},
> > > > > + {0xfd, 0x01},
> > > > > +};
> > > > > +
> > > > > +static const char * const ov02a10_test_pattern_menu[] = {
> > > > > + "Disabled",
> > > > > + "Color Bar",
> > > > > +};
> > > > > +
> > > > > +static const s64 link_freq_menu_items[] = {
> > > > > + OV02A10_LINK_FREQ_390MHZ
> > > > > +};
> > > > > +
> > > > > +static u64 to_pixel_rate(u32 f_index)
> > > > > +{
> > > > > + u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OV02A10_DATA_LANES;
> > > > > +
> > > > > + do_div(pixel_rate, OV02A10_BITS_PER_SAMPLE);
> > > > > +
> > > > > + return pixel_rate;
> > > > > +}
> > > > > +
> > > > > +static const struct ov02a10_mode supported_modes[] = {
> > > > > + {
> > > > > + .width = 1600,
> > > > > + .height = 1200,
> > > > > + .exp_def = 0x01ae,
> > > > > + .hts_def = 0x03a6,
> > > > > + .vts_def = 0x056e,
> > > > > + .reg_list = {
> > > > > + .num_of_regs = ARRAY_SIZE(ov02a10_1600x1200_regs),
> > > > > + .regs = ov02a10_1600x1200_regs,
> > > > > + },
> > > > > + },
> > > > > +};
> > > > > +
> > > > > +static int ov02a10_write_array(struct ov02a10 *ov02a10,
> > > > > + const struct ov02a10_reg_list *r_list)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + unsigned int i;
> > > > > + int ret;
> > > > > +
> > > > > + for (i = 0; i < r_list->num_of_regs; i++) {
> > > > > + ret = i2c_smbus_write_byte_data(client,
> > > > > + r_list->regs[i].addr,
> > > > > + r_list->regs[i].val);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_read_smbus(struct ov02a10 *ov02a10, unsigned char reg,
> > > > > + unsigned char *val)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret;
> > > > > +
> > > > > + ret = i2c_smbus_read_byte_data(client, reg);
> > > > > + if (ret >= 0) {
> > > > > + *val = (unsigned char)ret;
> > > > > + ret = 0;
> > > > > + }
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_mod_reg(struct ov02a10 *ov02a10, u8 reg, u8 mask, u8 val)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + u8 readval;
> > > > > + int ret;
> > > > > +
> > > > > + ret = ov02a10_read_smbus(ov02a10, reg, &readval);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + readval &= ~mask;
> > > > > + val &= mask;
> > > > > + val |= readval;
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client, reg, val);
> > > > > +}
> > > > > +
> > > > > +static void ov02a10_fill_fmt(const struct ov02a10_mode *mode,
> > > > > + struct v4l2_mbus_framefmt *fmt)
> > > > > +{
> > > > > + fmt->width = mode->width;
> > > > > + fmt->height = mode->height;
> > > > > + fmt->field = V4L2_FIELD_NONE;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_set_fmt(struct v4l2_subdev *sd,
> > > > > + struct v4l2_subdev_pad_config *cfg,
> > > > > + struct v4l2_subdev_format *fmt)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > > > > +
> > > > > + mutex_lock(&ov02a10->mutex);
> > > > > +
> > > > > + if (ov02a10->streaming) {
> > > > > + mutex_unlock(&ov02a10->mutex);
> > > > > + return -EBUSY;
> > > > > + }
> > > > > +
> > > > > + /* Only one sensor mode supported */
> > > > > + mbus_fmt->code = ov02a10->fmt.code;
> > > > > + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > > > > + ov02a10->fmt = fmt->format;
> > > > > +
> > > > > + mutex_unlock(&ov02a10->mutex);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_get_fmt(struct v4l2_subdev *sd,
> > > > > + struct v4l2_subdev_pad_config *cfg,
> > > > > + struct v4l2_subdev_format *fmt)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > + struct v4l2_mbus_framefmt *mbus_fmt = &fmt->format;
> > > > > +
> > > > > + mutex_lock(&ov02a10->mutex);
> > > > > +
> > > > > + fmt->format = ov02a10->fmt;
> > > > > + mbus_fmt->code = ov02a10->fmt.code;
> > > > > + ov02a10_fill_fmt(ov02a10->cur_mode, mbus_fmt);
> > > > > +
> > > > > + mutex_unlock(&ov02a10->mutex);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_enum_mbus_code(struct v4l2_subdev *sd,
> > > > > + struct v4l2_subdev_pad_config *cfg,
> > > > > + struct v4l2_subdev_mbus_code_enum *code)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > +
> > > > > + if (code->index >= ARRAY_SIZE(supported_modes))
> > > > > + return -EINVAL;
> > > > > +
> > > > > + code->code = ov02a10->fmt.code;
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_enum_frame_sizes(struct v4l2_subdev *sd,
> > > > > + struct v4l2_subdev_pad_config *cfg,
> > > > > + struct v4l2_subdev_frame_size_enum *fse)
> > > > > +{
> > > > > + if (fse->index >= ARRAY_SIZE(supported_modes))
> > > > > + return -EINVAL;
> > > > > +
> > > > > + fse->min_width = supported_modes[fse->index].width;
> > > > > + fse->max_width = supported_modes[fse->index].width;
> > > > > + fse->max_height = supported_modes[fse->index].height;
> > > > > + fse->min_height = supported_modes[fse->index].height;
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_check_sensor_id(struct ov02a10 *ov02a10)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + u16 id;
> > > > > + u8 pid = 0;
> > > > > + u8 ver = 0;
> > > > > + int ret;
> > > > > +
> > > > > + /* Check sensor revision */
> > > > > + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_H, &pid);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + ret = ov02a10_read_smbus(ov02a10, OV02A10_REG_CHIP_ID_L, &ver);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + id = OV02A10_ID(pid, ver);
> > > > > + if (id != CHIP_ID) {
> > > > > + dev_err(&client->dev, "Unexpected sensor id(%04x)\n", id);
> > > > > + return -EINVAL;
> > > > > + }
> > > > > +
> > > > > + dev_dbg(&client->dev, "Detected OV%04X sensor\n", id);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int __maybe_unused ov02a10_power_on(struct device *dev)
> > > > > +{
> > > > > + struct i2c_client *client = to_i2c_client(dev);
> > > > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > + int ret;
> > > > > +
> > > > > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_LOW);
> > > > > + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_HIGH);
> > > > > +
> > > > > + ret = clk_prepare_enable(ov02a10->eclk);
> > > > > + if (ret < 0) {
> > > > > + dev_err(dev, "failed to enable eclk\n");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + ret = regulator_bulk_enable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > > > > + if (ret < 0) {
> > > > > + dev_err(dev, "failed to enable regulators\n");
> > > > > + goto disable_clk;
> > > > > + }
> > > > > + usleep_range(5000, 6000);
> > > > > +
> > > > > + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_LOW);
> > > > > + usleep_range(5000, 6000);
> > > > > +
> > > > > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_HIGH);
> > > > > + usleep_range(5000, 6000);
> > > > > +
> > > > > + ret = ov02a10_check_sensor_id(ov02a10);
> > > > > + if (ret)
> > > > > + goto disable_regulator;
> > > > > +
> > > > > + return 0;
> > > > > +
> > > > > +disable_regulator:
> > > > > + regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > > > > +disable_clk:
> > > > > + clk_disable_unprepare(ov02a10->eclk);
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static int __maybe_unused ov02a10_power_off(struct device *dev)
> > > > > +{
> > > > > + struct i2c_client *client = to_i2c_client(dev);
> > > > > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > +
> > > > > + gpiod_set_value_cansleep(ov02a10->n_rst_gpio, GPIOD_OUT_LOW);
> > > > > + clk_disable_unprepare(ov02a10->eclk);
> > > > > + gpiod_set_value_cansleep(ov02a10->pd_gpio, GPIOD_OUT_HIGH);
> > > > > + regulator_bulk_disable(OV02A10_NUM_SUPPLIES, ov02a10->supplies);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int __ov02a10_start_stream(struct ov02a10 *ov02a10)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + const struct ov02a10_reg_list *reg_list;
> > > > > + int ret;
> > > > > +
> > > > > + /* Apply default values of current mode */
> > > > > + reg_list = &ov02a10->cur_mode->reg_list;
> > > > > + ret = ov02a10_write_array(ov02a10, reg_list);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + /* Apply customized values from user */
> > > > > + ret = __v4l2_ctrl_handler_setup(ov02a10->subdev.ctrl_handler);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + /* Set orientation to 180 degree */
> > > > > + if (ov02a10->upside_down) {
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_MIRROR_FLIP_CONTROL,
> > > > > + REG_MIRROR_FLIP_ENABLE);
> > > > > + if (ret) {
> > > > > + dev_err(&client->dev, "failed to set orientation\n");
> > > > > + return ret;
> > > > > + }
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > > > > + REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + /* Set clock lane transmission mode according to DT property */
> > > > > + ret = ov02a10_mod_reg(ov02a10, REG_HS_MODE_BLC, CLOCK_HS_MODE_ENABLE,
> > > > > + ov02a10->mipi_clock_hs_mode_enable ?
> > > > > + CLOCK_HS_MODE_ENABLE : 0);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + /* Set clock lane hs vod adjust to DT property */
> > > > > + ret = ov02a10_mod_reg(ov02a10, REG_HS_MODE_BLC, CLOCK_HS_VOD_ADJUST,
> > > > > + ov02a10->mipi_clock_hs_vod_adjust_cnt << 2);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + /* Set mipi tx speed according to DT property */
> > > > > + ret = i2c_smbus_write_byte_data(client, TX_SPEED_AREA_SEL,
> > > > > + ov02a10->mipi_clock_tx_speed);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + /* Set stream on register */
> > > > > + return i2c_smbus_write_byte_data(client,
> > > > > + REG_SC_CTRL_MODE,
> > > > > + SC_CTRL_MODE_STREAMING);
> > > > > +}
> > > > > +
> > > > > +static int __ov02a10_stop_stream(struct ov02a10 *ov02a10)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client,
> > > > > + REG_SC_CTRL_MODE, SC_CTRL_MODE_STANDBY);
> > > >
> > > > Alignment. Please run checkpatch.pl on this.
> > > >
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_entity_init_cfg(struct v4l2_subdev *sd,
> > > > > + struct v4l2_subdev_pad_config *cfg)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > + struct v4l2_subdev_format fmt = { 0 };
> > > > > +
> > > > > + fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> > > > > + fmt.format.width = ov02a10->cur_mode->width;
> > > > > + fmt.format.height = ov02a10->cur_mode->width;
> > > >
> > > > Please use the default mode, not the current one.
> > > >
> > > > > +
> > > > > + ov02a10_set_fmt(sd, cfg, &fmt);
> > > > > +
> > > > > + return 0;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_s_stream(struct v4l2_subdev *sd, int on)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = to_ov02a10(sd);
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret = 0;
> > > > > +
> > > > > + dev_dbg(&client->dev, "ov02a10 s_stream (%d)\n", on);
> > > > > + mutex_lock(&ov02a10->mutex);
> > > > > +
> > > > > + if (ov02a10->streaming == on)
> > > > > + goto unlock_and_return;
> > > > > +
> > > > > + if (on) {
> > > > > + ret = pm_runtime_get_sync(&client->dev);
> > > > > + if (ret < 0) {
> > > > > + pm_runtime_put_noidle(&client->dev);
> > > > > + goto unlock_and_return;
> > > > > + }
> > > > > +
> > > > > + ret = __ov02a10_start_stream(ov02a10);
> > > > > + if (ret) {
> > > > > + __ov02a10_stop_stream(ov02a10);
> > > > > + ov02a10->streaming = !on;
> > > > > + goto err_rpm_put;
> > > > > + }
> > > > > + } else {
> > > > > + __ov02a10_stop_stream(ov02a10);
> > > > > + pm_runtime_put(&client->dev);
> > > > > + }
> > > > > +
> > > > > + ov02a10->streaming = on;
> > > > > + mutex_unlock(&ov02a10->mutex);
> > > > > +
> > > > > + return ret;
> > > > > +
> > > > > +err_rpm_put:
> > > > > + pm_runtime_put(&client->dev);
> > > > > +unlock_and_return:
> > > > > + mutex_unlock(&ov02a10->mutex);
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static const struct dev_pm_ops ov02a10_pm_ops = {
> > > > > + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> > > > > + pm_runtime_force_resume)
> > > > > + SET_RUNTIME_PM_OPS(ov02a10_power_off, ov02a10_power_on, NULL)
> > > > > +};
> > > > > +
> > > > > +/*
> > > > > + * ov02a10_set_exposure - Function called when setting exposure time
> > > > > + * @priv: Pointer to device structure
> > > > > + * @val: Variable for exposure time, in the unit of micro-second
> > > > > + *
> > > > > + * Set exposure time based on input value.
> > > > > + *
> > > > > + * Return: 0 on success
> > > > > + */
> > > > > +static int ov02a10_set_exposure(struct ov02a10 *ov02a10, int val)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_H,
> > > > > + ((val >> OV02A10_EXP_SHIFT) &
> > > > > + OV02A10_MASK_8_BITS));
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_EXPOSURE_L,
> > > > > + (val & OV02A10_MASK_8_BITS));
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > > > > + REG_ENABLE);
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_set_gain(struct ov02a10 *ov02a10, int val)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_GAIN,
> > > > > + (val & OV02A10_MASK_8_BITS));
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > > > > + REG_ENABLE);
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_set_vblank(struct ov02a10 *ov02a10, int val)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_H,
> > > > > + (((val + ov02a10->cur_mode->height -
> > > > > + OV02A10_BASIC_LINE) >>
> > > > > + OV02A10_VTS_SHIFT) &
> > > > > + OV02A10_MASK_8_BITS));
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_VTS_L,
> > > > > + ((val + ov02a10->cur_mode->height -
> > > > > + OV02A10_BASIC_LINE) &
> > > > > + OV02A10_MASK_8_BITS));
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > > > > + REG_ENABLE);
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_set_test_pattern(struct ov02a10 *ov02a10, int pattern)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + int ret;
> > > > > +
> > > > > + if (pattern)
> > > > > + pattern = OV02A10_TEST_PATTERN_ENABLE;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_PAGE_SWITCH, REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, OV02A10_REG_TEST_PATTERN,
> > > > > + pattern);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + ret = i2c_smbus_write_byte_data(client, REG_GLOBAL_EFFECTIVE,
> > > > > + REG_ENABLE);
> > > > > + if (ret < 0)
> > > > > + return ret;
> > > > > +
> > > > > + return i2c_smbus_write_byte_data(client, REG_SC_CTRL_MODE,
> > > > > + SC_CTRL_MODE_STREAMING);
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_set_ctrl(struct v4l2_ctrl *ctrl)
> > > > > +{
> > > > > + struct ov02a10 *ov02a10 = container_of(ctrl->handler,
> > > > > + struct ov02a10, ctrl_handler);
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + s64 max_expo;
> > > > > + int ret = 0;
> > > > > +
> > > > > + /* Propagate change of current control to all related controls */
> > > > > + if (ctrl->id == V4L2_CID_VBLANK) {
> > > > > + /* Update max exposure while meeting expected vblanking */
> > > > > + max_expo = ov02a10->cur_mode->height + ctrl->val -
> > > > > + OV02A10_EXPOSURE_MAX_MARGIN;
> > > > > + __v4l2_ctrl_modify_range(ov02a10->exposure,
> > > > > + ov02a10->exposure->minimum, max_expo,
> > > > > + ov02a10->exposure->step,
> > > > > + ov02a10->exposure->default_value);
> > > > > + }
> > > > > +
> > > > > + /* V4L2 controls values will be applied only when power is already up */
> > > > > + if (!pm_runtime_get_if_in_use(&client->dev))
> > > > > + return 0;
> > > > > +
> > > > > + switch (ctrl->id) {
> > > > > + case V4L2_CID_EXPOSURE:
> > > > > + ret = ov02a10_set_exposure(ov02a10, ctrl->val);
> > > > > + break;
> > > > > + case V4L2_CID_ANALOGUE_GAIN:
> > > > > + ret = ov02a10_set_gain(ov02a10, ctrl->val);
> > > > > + break;
> > > > > + case V4L2_CID_VBLANK:
> > > > > + ret = ov02a10_set_vblank(ov02a10, ctrl->val);
> > > > > + break;
> > > > > + case V4L2_CID_TEST_PATTERN:
> > > > > + ret = ov02a10_set_test_pattern(ov02a10, ctrl->val);
> > > > > + break;
> > > > > + };
> > > > > +
> > > > > + pm_runtime_put(&client->dev);
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static const struct v4l2_subdev_video_ops ov02a10_video_ops = {
> > > > > + .s_stream = ov02a10_s_stream,
> > > > > +};
> > > > > +
> > > > > +static const struct v4l2_subdev_pad_ops ov02a10_pad_ops = {
> > > > > + .init_cfg = ov02a10_entity_init_cfg,
> > > > > + .enum_mbus_code = ov02a10_enum_mbus_code,
> > > > > + .enum_frame_size = ov02a10_enum_frame_sizes,
> > > > > + .get_fmt = ov02a10_get_fmt,
> > > > > + .set_fmt = ov02a10_set_fmt,
> > > > > +};
> > > > > +
> > > > > +static const struct v4l2_subdev_ops ov02a10_subdev_ops = {
> > > > > + .video = &ov02a10_video_ops,
> > > > > + .pad = &ov02a10_pad_ops,
> > > > > +};
> > > > > +
> > > > > +static const struct media_entity_operations ov02a10_subdev_entity_ops = {
> > > > > + .link_validate = v4l2_subdev_link_validate,
> > > > > +};
> > > > > +
> > > > > +static const struct v4l2_ctrl_ops ov02a10_ctrl_ops = {
> > > > > + .s_ctrl = ov02a10_set_ctrl,
> > > > > +};
> > > > > +
> > > > > +static int ov02a10_initialize_controls(struct ov02a10 *ov02a10)
> > > > > +{
> > > > > + struct i2c_client *client = v4l2_get_subdevdata(&ov02a10->subdev);
> > > > > + const struct ov02a10_mode *mode;
> > > > > + struct v4l2_ctrl_handler *handler;
> > > > > + struct v4l2_ctrl *ctrl;
> > > > > + u64 exposure_max;
> > > > > + u32 pixel_rate, h_blank;
> > > > > + int ret;
> > > > > +
> > > > > + handler = &ov02a10->ctrl_handler;
> > > > > + mode = ov02a10->cur_mode;
> > > > > + ret = v4l2_ctrl_handler_init(handler, 7);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + handler->lock = &ov02a10->mutex;
> > > > > +
> > > > > + ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ,
> > > > > + 0, 0, link_freq_menu_items);
> > > > > + if (ctrl)
> > > > > + ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > > > > +
> > > > > + pixel_rate = to_pixel_rate(0);
> > > > > + v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE,
> > > > > + 0, pixel_rate, 1, pixel_rate);
> > > > > +
> > > > > + h_blank = mode->hts_def - mode->width;
> > > > > + ov02a10->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK,
> > > > > + h_blank, h_blank, 1, h_blank);
> > > > > + if (ov02a10->hblank)
> > > > > + ov02a10->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > > > > +
> > > > > + ov02a10->vblank = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > > > > + V4L2_CID_VBLANK, mode->vts_def -
> > > > > + mode->height,
> > > > > + OV02A10_VTS_MAX - mode->height, 1,
> > > > > + mode->vts_def - mode->height);
> > > > > +
> > > > > + exposure_max = mode->vts_def - 4;
> > > > > + ov02a10->exposure = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > > > > + V4L2_CID_EXPOSURE,
> > > > > + OV02A10_EXPOSURE_MIN,
> > > > > + exposure_max,
> > > > > + OV02A10_EXPOSURE_STEP,
> > > > > + mode->exp_def);
> > > > > +
> > > > > + ov02a10->anal_gain = v4l2_ctrl_new_std(handler, &ov02a10_ctrl_ops,
> > > > > + V4L2_CID_ANALOGUE_GAIN,
> > > > > + OV02A10_GAIN_MIN,
> > > > > + OV02A10_GAIN_MAX,
> > > > > + OV02A10_GAIN_STEP,
> > > > > + OV02A10_GAIN_DEFAULT);
> > > > > +
> > > > > + ov02a10->test_pattern =
> > > > > + v4l2_ctrl_new_std_menu_items(handler,
> > > > > + &ov02a10_ctrl_ops,
> > > > > + V4L2_CID_TEST_PATTERN,
> > > > > + ARRAY_SIZE(ov02a10_test_pattern_menu) -
> > > > > + 1, 0, 0,
> > > > > + ov02a10_test_pattern_menu);
> > > > > +
> > > > > + if (handler->error) {
> > > > > + ret = handler->error;
> > > > > + dev_err(&client->dev, "failed to init controls(%d)\n", ret);
> > > > > + goto err_free_handler;
> > > > > + }
> > > > > +
> > > > > + ov02a10->subdev.ctrl_handler = handler;
> > > > > +
> > > > > + return 0;
> > > > > +
> > > > > +err_free_handler:
> > > > > + v4l2_ctrl_handler_free(handler);
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_check_hwcfg(struct device *dev, struct ov02a10 *ov02a10)
> > > > > +{
> > > > > + struct fwnode_handle *ep;
> > > > > + struct fwnode_handle *fwnode = dev_fwnode(dev);
> > > > > + struct v4l2_fwnode_endpoint bus_cfg = {
> > > > > + .bus_type = V4L2_MBUS_CSI2_DPHY
> > > > > + };
> > > > > + unsigned int i, j;
> > > > > + int ret;
> > > > > +
> > > > > + if (!fwnode)
> > > > > + return -ENXIO;
> > > > > +
> > > > > + ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
> > > > > + if (!ep)
> > > > > + return -ENXIO;
> > > > > +
> > > > > + ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg);
> > > > > + fwnode_handle_put(ep);
> > > > > + if (ret)
> > > > > + return ret;
> > > > > +
> > > > > + /* Optional indication of mipi clock lane mode */
> > > > > + if (bus_cfg.bus.mipi_csi2.flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK)
> > > > > + ov02a10->mipi_clock_hs_mode_enable = true;
> > > > > +
> > > > > + if (!bus_cfg.nr_of_link_frequencies) {
> > > > > + dev_err(dev, "no link frequencies defined");
> > > > > + ret = -EINVAL;
> > > > > + goto check_hwcfg_error;
> > > > > + }
> > > > > +
> > > > > + for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) {
> > > > > + for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) {
> > > > > + if (link_freq_menu_items[i] ==
> > > > > + bus_cfg.link_frequencies[j])
> > > > > + break;
> > > > > + }
> > > > > +
> > > > > + if (j == bus_cfg.nr_of_link_frequencies) {
> > > > > + dev_err(dev, "no link frequency %lld supported",
> > > > > + link_freq_menu_items[i]);
> > > > > + ret = -EINVAL;
> > > > > + goto check_hwcfg_error;
> > > > > + }
> > > > > + }
> > > > > +
> > > > > +check_hwcfg_error:
> > > > > + v4l2_fwnode_endpoint_free(&bus_cfg);
> > > > > +
> > > > > + return ret;
> > > > > +}
> > > > > +
> > > > > +static int ov02a10_probe(struct i2c_client *client)
> > > > > +{
> > > > > + struct device *dev = &client->dev;
> > > > > + struct ov02a10 *ov02a10;
> > > > > + unsigned int rotation;
> > > > > + unsigned int clock_lane_tx_speed;
> > > > > + unsigned int hs_vod_adjust_cnt;
> > > > > + unsigned int i;
> > > > > + int ret;
> > > > > +
> > > > > + ov02a10 = devm_kzalloc(dev, sizeof(*ov02a10), GFP_KERNEL);
> > > > > + if (!ov02a10)
> > > > > + return -ENOMEM;
> > > > > +
> > > > > + ret = ov02a10_check_hwcfg(dev, ov02a10);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to check HW configuration: %d", ret);
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + v4l2_i2c_subdev_init(&ov02a10->subdev, client, &ov02a10_subdev_ops);
> > > > > + ov02a10->fmt.code = MEDIA_BUS_FMT_SBGGR10_1X10;
> > > > > +
> > > > > + /* Optional indication of physical rotation of sensor */
> > > > > + ret = fwnode_property_read_u32(dev_fwnode(dev), "rotation",
> > > > > + &rotation);
> > > > > + if (!ret) {
> > > > > + switch (rotation) {
> > > > > + case 180:
> > > > > + ov02a10->upside_down = true;
> > > > > + ov02a10->fmt.code = MEDIA_BUS_FMT_SRGGB10_1X10;
> > > > > + break;
> > > > > + case 0:
> > > > > + break;
> > > > > + default:
> > > > > + dev_warn(dev, "%u degrees rotation is not supported, ignoring...\n",
> > > > > + rotation);
> > > > > + }
> > > > > + }
> > > > > +
> > > > > + /* Optional indication of HS VOD adjust */
> > > > > + ret = fwnode_property_read_u32(dev_fwnode(dev),
> > > > > + "ovti,hs-vod-adjust",
> > > >
> > > > Fits on previous line.
> > > >
> > > > > + &hs_vod_adjust_cnt);
> > > > > + if (!ret)
> > > > > + ov02a10->mipi_clock_hs_vod_adjust_cnt = hs_vod_adjust_cnt;
> > > > > + else
> > > > > + dev_warn(dev, "failed to get hs vod adjust, using default\n");
> > > > > +
> > > > > + /* Optional indication of mipi tx speed */
> > > > > + ret = fwnode_property_read_u32(dev_fwnode(dev),
> > > > > + "ovti,mipi-tx-speed",
> > > >
> > > > I guess this does, too.
> > > >
> > > > Neither property is documented in bindings. What are they for?
> > > >
> > > > > + &clock_lane_tx_speed);
> > > > > +
> > > > > + if (!ret)
> > > > > + ov02a10->mipi_clock_tx_speed = clock_lane_tx_speed;
> > > > > + else
> > > > > + dev_warn(dev, "failed to get mipi tx speed, using default\n");
> > > > > +
> > > > > + /* Get system clock (eclk) */
> > > > > + ov02a10->eclk = devm_clk_get(dev, "eclk");
> > > > > + if (IS_ERR(ov02a10->eclk)) {
> > > > > + dev_err(dev, "failed to get eclk\n");
> > > > > + return -EINVAL;
> > > > > + }
> > > > > +
> > > > > + ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency",
> > > > > + &ov02a10->eclk_freq);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to get eclk frequency\n");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + ret = clk_set_rate(ov02a10->eclk, ov02a10->eclk_freq);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to set eclk frequency (24MHz)\n");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + if (clk_get_rate(ov02a10->eclk) != OV02A10_ECLK_FREQ) {
> > > > > + dev_warn(dev, "wrong eclk frequency %d Hz, expected: %d Hz\n",
> > > > > + ov02a10->eclk_freq, OV02A10_ECLK_FREQ);
> > > > > + return -EINVAL;
> > > > > + }
> > > > > +
> > > > > + ov02a10->pd_gpio = devm_gpiod_get(dev, "powerdown", GPIOD_OUT_HIGH);
> > > > > + if (IS_ERR(ov02a10->pd_gpio)) {
> > > > > + dev_err(dev, "failed to get powerdown-gpios\n");
> > > > > + return -EINVAL;
> > > > > + }
> > > > > +
> > > > > + ov02a10->n_rst_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW);
> > > > > + if (IS_ERR(ov02a10->n_rst_gpio)) {
> > > > > + dev_err(dev, "failed to get reset-gpios\n");
> > > > > + return -EINVAL;
> > > > > + }
> > > > > +
> > > > > + for (i = 0; i < OV02A10_NUM_SUPPLIES; i++)
> > > > > + ov02a10->supplies[i].supply = ov02a10_supply_names[i];
> > > > > +
> > > > > + ret = devm_regulator_bulk_get(dev, OV02A10_NUM_SUPPLIES,
> > > > > + ov02a10->supplies);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to get regulators\n");
> > > > > + return ret;
> > > > > + }
> > > > > +
> > > > > + mutex_init(&ov02a10->mutex);
> > > > > + ov02a10->cur_mode = &supported_modes[0];
> > > > > + ret = ov02a10_initialize_controls(ov02a10);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to initialize controls\n");
> > > > > + goto err_destroy_mutex;
> > > > > + }
> > > > > +
> > > > > + ov02a10->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > > > > + ov02a10->subdev.entity.ops = &ov02a10_subdev_entity_ops;
> > > > > + ov02a10->subdev.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> > > > > + ov02a10->pad.flags = MEDIA_PAD_FL_SOURCE;
> > > > > + ret = media_entity_pads_init(&ov02a10->subdev.entity, 1, &ov02a10->pad);
> > > > > + if (ret < 0) {
> > > > > + dev_err(dev, "failed to init entity pads: %d", ret);
> > > > > + goto err_free_handler;
> > > > > + }
> > > > > +
> > > > > + ret = v4l2_async_register_subdev(&ov02a10->subdev);
> > > > > + if (ret) {
> > > > > + dev_err(dev, "failed to register V4L2 subdev: %d", ret);
> > > > > + goto err_clean_entity;
> > > > > + }
> > > > > +
> > > > > + pm_runtime_enable(dev);
> > > >
> > > > You also need pm_runtime_set_active() before pm_runtime_enable(), and to
> > > > power the device down, pm_runtime_idle() after it.
> > > >
> > > > Where did you power up the sensor?
> > > >
> > >
> > > Why do we need to power it up? I think probe is expected to leave it
> > > powered off.
> >
> > I missed the driver does not power the sensor on for verifying it's really
> > there.
> >
> > That's not really an issue I guess. But this also results in the driver not
> > working without runtime PM: the driver needs to explicitly power on the
> > device in that case.
>
> Good point, I keep forgetting about this. Perhaps something like this
> in _probe() could work?
>
> pm_runtime_enable(dev);
> if (!pm_runtime_enabled(dev))
> ov02a10_power_on(...);
>
> Then _remove() would handle this naturally, because it checks for
> !pm_runtime_status_suspended() and that function returns false ifndef
> CONFIG_PM.
I'd rely on #ifdefs: runtime PM can also be disabled through sysfs.
--
Regards,
Sakari Ailus
