On 05/11/2019 14.15, Grygorii Strashko wrote: > > > On 05/11/2019 11:58, Linus Walleij wrote: >> On Mon, Nov 4, 2019 at 8:11 PM Rob Herring <robh+dt@xxxxxxxxxx> wrote: >>> [Peter] >>>> The device needs the RST line to be high, otherwise it is not >>>> accessible. If it does not have reset control how can we make sure that >>>> the GPIO line is in correct state? >>> >>> Just like the reset code, drivers register their use of the reset and >>> the core tracks users and prevents resetting when not safe. Maybe the >>> reset subsystem needs to learn about GPIO resets. (...) >> >> I agree. Certainly the reset subsystem can do what the regulator >> subsystem is already doing: request the GPIO line nonexclusive >> and handle any reference counting and/or quirks that are needed >> in a hypothetical drivers/reset/reset-gpio.c driver. >> >> There is no such driver today, just a "reset" driver in >> drivers/power/reset that resets the whole system. >> >> But I see no problem in creating a proper reset driver in drivers/reset >> to handle a few peripherals with a shared GPIO reset line. > > Personally, I agree with Mark's comment here: > >> [Mark] >> The theory with that was that any usage of this would need the >> higher level code using the GPIO to cooperate so they didn't step >> on each other's toes so the GPIO code should just punt to it. >> >>> But let's say that a board design will pick two components (C1 and C2) >>> and use the same GPIO line to enable them. We already have the drivers >>> for them and they are used in boards already. >> >> This is basically an attempt to make a generic implementation of >> that cooperation for simple cases. >> > > This looks like unsolvable problem in generic way. > Lets assume there are some generic shared reset controller invented, but > then > - What if some driver is loaded/unloaded and corresponding device uses > shared > reset which is de-asserted already? > In this case, driver should never ever expect that target device has all > registers in default state. > - What if reset is required as part of error recovery procedure? The > error recovery > will not be supported by such design. > - PM: Device reset could be part of suspend/resume sequence. if one of > the devices > is wake-up source, but other are not, those devices might be in very > unexpected state during resume. > - There could be dependencies on reset timings, shared reset might work for > similar devices (like set of net phys) and does not work if connected > devices are different. and some driver shamelessly implements runtime power/reset control while other driver does not (they were never used on board where they had shared GPIO, probably power at most) > > It seems, the only one case when it might help is system boot when: > - similar devices are connected to the reset line > - drivers are not expected to be re-loaded > - device reset is not part of any recovery procedure > - safe reset timings can be defined for all connected devices > (but hey - if this is boot only then gpio-hogs should work. Are they?) That is another thing which almost works ;) w/o gpio binding deferred probing is not possible if the GPIO controller is probed later. In some cases it might be even impossible to make sure that the GPIO controller would probe first (GPIO extender on different i2c bus than the user(s) of the gpio line) In some cases moving around nodes in DT might artificially make things work, but then someone compiles the expander as module, or some 'small' change in kernel and the probe order on the bus changes. I don't think it is a valid thing to have commits on the DT files saying: move the expander front/after the hog affected user since since Monday the probe order has changed. Then move it back two weeks later ;) > > Actually, MDIO bus is one such example where reset line can be toggled by > as by MDIO bus controller as by PHY drivers. > > So, even thing will move forward with this - it'll be good to have noted > above restrictions in documentation. > - Péter Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
