Re: [PATCH v2 2/2] PCI: qcom: Add support for SDM845 PCIe controller

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Bjorn,

On Fri, 2019-11-01 at 17:27 -0700, Bjorn Andersson wrote:
> The SDM845 has one Gen2 and one Gen3 controller, add support for these.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> ---
> 
> Changes since v1:
> - Style changes requested by Stan
> - Tested with second PCIe controller as well
> 
>  drivers/pci/controller/dwc/pcie-qcom.c | 152 +++++++++++++++++++++++++
>  1 file changed, 152 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 7e581748ee9f..35f4980480bb 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -54,6 +54,7 @@
[...]
> +static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
> +	struct dw_pcie *pci = pcie->pci;
> +	struct device *dev = pci->dev;
> +	u32 val;
> +	int ret;
> +
> +	ret = regulator_bulk_enable(ARRAY_SIZE(res->supplies), res->supplies);
> +	if (ret < 0) {
> +		dev_err(dev, "cannot enable regulators\n");
> +		return ret;
> +	}
> +
> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	if (ret < 0)
> +		goto err_disable_regulators;
> +
> +	ret = reset_control_assert(res->pci_reset);
> +	if (ret < 0) {
> +		dev_err(dev, "cannot deassert pci reset\n");
> +		goto err_disable_clocks;
> +	}

If for any of the above fails, the reset line is left in its default
state, presumably unasserted. Is there a reason to assert and keep it
asserted if enabling the clocks fails below?

> +	msleep(20);
> +
> +	ret = reset_control_deassert(res->pci_reset);
> +	if (ret < 0) {
> +		dev_err(dev, "cannot deassert pci reset\n");
> +		goto err_assert_resets;

Nitpick: this seems superfluous since the reset line was just asserted
20 ms before. Maybe just:

		goto err_disable_clocks;

> +	}
> +
> +	ret = clk_prepare_enable(res->pipe_clk);
> +	if (ret) {
> +		dev_err(dev, "cannot prepare/enable pipe clock\n");
> +		goto err_assert_resets;
> +	}
> +
> +	/* configure PCIe to RC mode */
> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> +
> +	/* enable PCIe clocks and resets */
> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> +	val &= ~BIT(0);
> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> +	/* change DBI base address */
> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> +	/* MAC PHY_POWERDOWN MUX DISABLE  */
> +	val = readl(pcie->parf + PCIE20_PARF_SYS_CTRL);
> +	val &= ~BIT(29);
> +	writel(val, pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> +	val = readl(pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +	val |= BIT(4);
> +	writel(val, pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +
> +	if (IS_ENABLED(CONFIG_PCI_MSI)) {
> +		val = readl(pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
> +		val |= BIT(31);
> +		writel(val, pcie->parf + PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT);
> +	}
> +
> +	return 0;
> +err_assert_resets:
> +	reset_control_assert(res->pci_reset);

So maybe this can just be removed. The reset isn't asserted in deinit
either.

regards
Philipp




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux