Re: [PATCH v4 5/5] clk: qcom: Add Global Clock controller (GCC) driver for SC7180

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Matthias,

Thanks for your comments.

On 10/29/2019 11:29 PM, Matthias Kaehlcke wrote:
Hi Taniya,

On Mon, Oct 14, 2019 at 03:53:08PM +0530, Taniya Das wrote:
Add support for the global clock controller found on SC7180
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.

Signed-off-by: Taniya Das <tdas@xxxxxxxxxxxxxx>


v3 also had

+	[GCC_DISP_AHB_CLK] = &gcc_disp_ahb_clk.clkr,

Removing it makes the dpu_mdss driver unhappy:

[    2.999855] dpu_mdss_enable+0x2c/0x58->msm_dss_enable_clk: 'iface' is not available

because:

         mdss: mdss@ae00000 {
     	        ...

  =>             clocks = <&gcc GCC_DISP_AHB_CLK>,
                          <&gcc GCC_DISP_HF_AXI_CLK>,
                          <&dispcc DISP_CC_MDSS_MDP_CLK>;
                 clock-names = "iface", "gcc_bus", "core";
	};


The basic idea as you mentioned below was to move the CRITICAL clocks to probe. The clock provider to return NULL in case the clocks are not registered.
This was discussed with Stephen on v3. Thus I submitted the below patch.
clk: qcom: common: Return NULL from clk_hw OF provider.

Yes it would throw these warnings, but no functional issue is observed from display. I have tested it on the cheza board. I guess we could fix the DRM driver to use the "devm_clk_get_optional()" instead?

More clocks were removed in v4:

-       [GCC_CPUSS_GNOC_CLK] = &gcc_cpuss_gnoc_clk.clkr,
-       [GCC_GPU_CFG_AHB_CLK] = &gcc_gpu_cfg_ahb_clk.clkr,
-       [GCC_VIDEO_AHB_CLK] = &gcc_video_ahb_clk.clkr,

I guess this part of "remove registering the CRITICAL clocks to clock provider
and leave them always ON from the GCC probe." (change log entry), but are you
sure nobody is going to reference these clocks?


Even if they are referenced clk provider would return NULL.

+static int gcc_sc7180_probe(struct platform_device *pdev)
+{
+	struct regmap *regmap;
+	int ret;
+
+	regmap = qcom_cc_map(pdev, &gcc_sc7180_desc);
+	if (IS_ERR(regmap))
+		return PTR_ERR(regmap);
+
+	/*
+	 * Disable the GPLL0 active input to MM blocks, NPU
+	 * and GPU via MISC registers.
+	 */
+	regmap_update_bits(regmap, 0x09ffc, 0x3, 0x3);
+	regmap_update_bits(regmap, 0x4d110, 0x3, 0x3);
+	regmap_update_bits(regmap, 0x71028, 0x3, 0x3);

In v3 this was:

	regmap_update_bits(regmap, GCC_MMSS_MISC, 0x3, 0x3);
	regmap_update_bits(regmap, GCC_NPU_MISC, 0x3, 0x3);
	regmap_update_bits(regmap, GCC_GPU_MISC, 0x3, 0x3);

IMO register names seem preferable, why switch to literal addresses
instead?


:). These cleanups where done based on the comments I had received during SDM845 review. If Stephen is fine moving them to names, I could submit them in the next patch series.

+
+	/*
+	 * Keep the clocks always-ON
+	 * GCC_CPUSS_GNOC_CLK, GCC_VIDEO_AHB_CLK, GCC_DISP_AHB_CLK
+	 * GCC_GPU_CFG_AHB_CLK
+	 */
+	regmap_update_bits(regmap, 0x48004, BIT(0), BIT(0));
+	regmap_update_bits(regmap, 0x0b004, BIT(0), BIT(0));
+	regmap_update_bits(regmap, 0x0b00c, BIT(0), BIT(0));
+	regmap_update_bits(regmap, 0x71004, BIT(0), BIT(0));

ditto, register names seem preferable.


--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation.

--



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux